Design of optimum signals for the simultaneous estimation of timedelay and Doppler shift

The problem of joint estimation of time delay and Doppler shift is considered from the point of view of the Wigner distribution of the signal. A very efficient method of obtaining the optimum signal with minimum estimation error based on the convexity of the design region is developed. Practical applications, however, require the signal to satisfy other constraints which present complications in acquiring the optimum signal. A design approach based on the method of simulated annealing is suggested to solve for the optimum signal under constraints. The performance of the signals so obtained is evaluated and compared with that of signals obtained by synthesis     

深斜井永久式封隔器两种套铣方式风险分析与优化措施

在深斜井大修作业中,为了适应海上修井机作业能力的需要,需要处理井下永久式封隔器。采用磨铣方式处理难度大、周期长、费用高,因此通常采取套铣方式,仅将可钻式永久性封隔器卡瓦及密封套铣掉,再打捞回收或下推至人工井底,直至不妨碍下一步作业。从作业井实际情况出发,针对深斜井永久式封隔器,采用了两种不同动力驱动方式进行套铣处理:一种是地面转盘驱动,井下全部钻具都处于旋转状态,全程摩阻及扭矩大,可以施加较大钻压;另一种为井下马达驱动,即只有马达以下钻具旋转,而马达以上钻具不转,从而降低摩阻,但施加钻压较小,否则容易引起马达失速,所以对马达性能要求较高。通过套铣风险对比分析,分别对两种套铣钻具与参数进行了优化,提出了套铣成功与否的判断依据,为现场应用提供了借鉴。     

奥钢联板坯连铸计算机系统升级研究

某钢厂板坯连铸过程控制系统采用的奥钢联(VAI)技术,运行数年来,由于模型不透明,维护和调整困难,迫切需要升级改造。改造后的计算机系统充分考虑现有资源和需求,能够达到升级改造的目的。     

橡胶装置膨胀干燥机液力耦合器故障诊断及处理办法

橡胶装置后处理关键机组膨胀干燥机的液力耦合器振动异常，严重影响机组的安全运行，一旦机组振动引起跳车，后处理整条线将停产，于是对该机组进行密切监测，并及时进行振动分析及故障诊断，提出了处理办法。     

Effects of various post-treatments on carbon nanotube films for reliable field emission

In this report, the FE characteristics of carbon nanotubes (CNTs) treated using both thermal annealing and mechanical coatings on the as-grown CNTs systematically studied. It was found that in the high temperature annealed samples, CNTs were attacked at its root during annealing due to a small amount of oxygen, and were pulled out of the substrate in places after FE measurements because of the contact resistance. However, for the mechanically coated samples both with spin on glass (SOG) and polymethyl methacrylate (PMMA), CNTs were found to be nearly intact after FE measurements and showed reliable FE characteristics over repeatable voltage scan. The reliability of CNTs during FE could be owing to the strong adhesion of CNTs to the substrate both by SOG and PMMA coatings.     

China＇s Electric Power Reform：Different Economics and Challenges

China＇s electric power reform has followed the western reform format, however, it doest not seem to have endorsed the liberalization ideology underlying the reform model. This raises the concern of whether and how a competitive power market may be established and reform objectives reached. The new market competition model is easy to build in theory. The experience of many countries suggests that the market reform is extremely difficult because of the interruptions by different interest groups. To transform a centrally planned power sector into a competitive power market is a daunting task. Policy makers need to take into consideration the transitional nature of the economy and power industry as they implement the competitive power market model.     

高频超声波在氧化皮中传播性能标定

对高频超声小在12Cr2MoWVTiB(G102钢）和12Cr1MoV钢钢管运行所产生氧化皮中的传播速度进行了定量标定，并对标定误差进行了统计计算，结果表明，12Cr1MoV钢氧化皮测厚标定点最大偶然误差值为0．050mm,G102钢为0．030mm，并指明了误差来源。     

GCr15轴承钢的热变形模拟试验研究

利用先进的Gleeble-2000热模拟试验机，对GCr15轴承钢某一轧制过程进行模拟试验，测定出GCr15轴承钢动态CCT曲线，并结合微观组织分析，制定合理的GCr15轴承钢轧后控制冷却工艺，以期达到提高GCr15轴承钢质量的最终目的。     

通用雷达故障诊断专家系统的设计

目的：为了提高雷达装备故障诊断的效率和可靠性。方法：通过对雷达装备综合测试和故障诊断要求和方法的分析。介绍一种适用于雷达装备的故障智能诊断专家模型，探讨了该模型的基本结构和相应的推理机制及故障诊断策略。结果：结论雷达故障诊断的特点，研究了该模型及诊断方法在雷达装备中的具体应用，证实了该方法是有效的。结论：将自动测试技术和专家系统相结合，可以提高故障诊断的效率和可靠性。     

配网侧接入电源对负荷建模的影响

研究了配网侧接入电源对负荷建模的影响。发现当配网侧电源的发电容量逐渐增大时，原有的感应电动机并联恒阻抗、恒电流、恒功率（ZIP）模型的负荷模型将不再能很好地反映该区域的负荷特性，进而提出了一种新的负荷模型结构———异步发电机并联ZIP模型。通过仿真计算，验证了该新负荷模型的有效性，并进一步统一了上述2种负荷模型，称为异步机并联ZIP负荷模型。