Ultra-strong, well-apodised Bragg gratings in chalcogenide rib waveguides

The first ultra-strong, near-perfect, raised-apodised Bragg gratings in As/sub 2/S/sub 3/ chalcogenide rib waveguides using /spl lambda/=532 nm light and a modified Sagnac holographic writing setup are demonstrated. Good agreement is achieved between the experimental results and the numerical modelling of the gratings using the transfer matrix analysis for thin film structures.     

Long-term working memory in the rat: Effects of hippocampally applied anisomycin.

The extent to which protein synthesis is involved in working memory was investigated with the protein synthesis inhibitor anisomycin (ANI). Male albino and Long-Evans rats were trained to perform accurately on a 12-arm radial maze when delays of 240 min were interposed between Choice 6 and Choice 7. Bilateral hippocampal cannulas were then implanted. Accuracy on Choices 7–22 was studied when ANI (80 μg/μl) or saline was injected either 30 min before Choice 1 or 5–20 min after Choice 6 in Exp I. Pretrial injection of ANI significantly impaired performance following the 240-min delay, whereas ANI injected during the delay had no such effect. In Exps II and III, the ANI-induced amnesia was replicated, and the temporal course of development of the amnesia was determined. Pretrial administration of ANI did not significantly affect retention after a 2-min delay but produced amnesia after delays of 15 min or longer. Data suggest that protein synthesis is important for the formation of temporary memories, provided the retention interval is long enough. It is suggested that working memory includes both short- and long-term components. Protein synthesis appears to be important for formation of the long-term component, but not the short-term component, of working memory. (31 ref) (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Dynamic viscosities of mixtures of n-butyraldehyde and isobutyraldehyde over wide ranges in the state parameters

Dynamic-viscosity measurements are reported for liquid mixtures in the system formed by n-butyraldehyde and isobutyraldehyde.Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 48, No. 2, pp. 321–322, February, 1985.     

Calculation of approximate weight functions in fracture mechanics by FEM

A method is presented for the calculation of weight functions used in fracture mechanics to determine stress intensity factors of cracks loaded by stress gradients. The reference solution for the stress intensity factor and for the reference crack opening displacement field is computed numerically by use of finite elements. The accuracy of the method is checked by comparison with well-known solutions from the literature.     

Calculation of stress concentration in the manipulator element using a combined finite and boundary element method

Elastic stress concentration in a manipulator element is calculated within the framework of the two-dimensional stressed state model. The purpose here is to make recommendations for selecting the radius of joining of the beam parts of the element based on analysis of maximum stresses in the stress concentration zone. Combination of the finite element and boundary element methods is proposed for solving the problem. A coarse finite element subdivision is used for the initial calculation for the entire element. Then, the solution is refined by using boundary elements in the identified zone. Comparison of calculation results with solutions obtained by the finite element and boundary element methods points to the effectiveness of the proposed algorithm for stress concentration calculations.Translated from Problemy Prochnosti, No. 6, pp. 72–74, June, 1991.     

ESD–RF co-design methodology for the state of the art RF-CMOS blocks

This paper describes an approach to design ESD protection for integrated low noise amplifier (LNA) circuits used in narrowband transceiver front-ends. The RF constraints on the implementation of ESD protection devices are relaxed by co-designing the RF and the ESD blocks, considering them as one single circuit to optimise. The method is applied for the design of 0.25 μm CMOS LNA. Circuit protection levels higher than 3 kV HBM stress are achieved using conventional highly capacitive ggNMOS snapback devices. The methodology can be extended to other RF-CMOS circuits requiring ESD protection by merging the ESD devices in the functionality of the corresponding matching blocks.     

Enabling simulation interoperability

Over the past years a series of architectures have addressed the need to link multiple simulations. These efforts have been driven primarily by the desire to reuse existing "best of breed" simulations in new combinations to avoid developing any single, monolithic architecture with the impossible goal of meeting all simulation needs. The US Department of Defense began developing the high level architecture (HLA) for distributed computer simulation systems. The high level architecture addresses the need to link multiple computer simulation systems. HLA separates the data model from the architecture's functions for exchanging information.     

Fluidized bed heat treatment of cast Al-Si-Cu-Mg alloys

The effects of fluidized bed heat treatment on the microstructural and mechanical properties of Al-Si-Cu-Mg cast alloys, namely, 354 and 319, were studied. The heating rate in fluidized beds (FBs) is greatervis-à-vis conventional electrical resistance furnaces (CFs). The high heating rate in FBs increases the kinetics of metallurgical phenomena such as Si fragmentation and spherodization during solution heat treatment, as well as the precipitation rate of phases such as Al₅Cu₂Mg₈Si₆ and Al₂Cu during aging. It is observed that the dissolution rate of phases such as Mg₂Si and Al₅Cu₂Mg₈Si₆ takes place very rapidly. The solution heat treatment of 319 alloy using FB results in complete dissolution of Mg₂Si and Al₅Cu₂Mg₈Si₆ particles within 45 minutes. However, for phases such as Al₂Cu and Ferich intermetallics, the dissolution rate is relatively slow. Even on prolonged solution heat treatment for 6 hours, these phases do not dissolve completely. It is observed that incomplete dissolution of the Al₂Cu phase does not significantly affect tensile properties of T4-treated alloys. The optimum solution heat-treatment time in FB for both 354 and 319 alloys is 45 minutes at 527 °C and 493 °C, respectively. Thermal analysis shows an exothermic peak owing to recrystallization and coarsening of eutectic grains during solution heat treatment. The high heating rate in FB causes this transformation to take place at a lower temperature than in CF. It is observed that the nucleation rate of Al₅Cu₂Mg₈Si₆ during aging in FB is greater than using CF. Thermal analysis of samples during the ramp-up stage while aging using FB did not show any phase transformation, while those using CF show two endothermic transformations, which are most likely due to the dissolution of GP zones or the co-cluster of solutes. Aging at 200 °C results in a greater number density of precipitates than those at 240 °C. The tensile strength of samples aged at 200 °C is greater than those aged at 240 °C, because the amount of precipitates formed at 200 °C is greater than that at 240 °C. The total heat-treatment time for T6 temper is less than 2 hours in FBs, which is a significant reduction in heat-treatment time, as well as energy consumption.     

Indoor body-area channel model for narrowband communications

Using wireless sensors placed on a person to continuously monitor health information is a promising new application. At the same time, new low-power wireless standards such as Bluetooth and Zigbee have been proposed for short range, low data-rate communication matching the requirements of these bio-medical applications. However, there are currently few measurements or models describing propagation around the body. To address this problem, electromagnetic waves near the torso are measured and a statistical model is derived for communication in the 915 MHz and 2.45 GHz industrial, scientific and medical bands associated with Zigbee and Bluetooth. Measurement setup and statistical analysis are described.