Numerical Simulation of Deforming Manufacture Process for Automobile Bevel Gear Blank

1 Introduction Rear axle bevel gearis a vital kind of annular accessory with high precision and hugeload availablefeatures ,andit is widely used as the differential drive in automobiles and tractor .In China ,the traditional manufactureapproach of producing the rear axle bevel gear blankis die forging,which not only requires a highinvestment ofproduct equipments , but also involves a low material utilization and great noise .In order to overcome thesedrawbacks , manyresearchers have done a gre…     

西门子S7-200可编程控制器在气化油点火技术中的应用

以西门子S7—200PLC为核心。利用火检探头。温度、压力等传感器，结合STEP 7 MicmwIN V3．1以及ProTool Pro CS工业组态软件完成了对点火过程的自动控制。实现了西门子S7—200PLC在大型发电厂410吨级蒸汽锅炉“气化油直接点燃煤粉技术”中的应用。提高了锅炉点火系统运行的自动化水平。     

Neural-fuzzy classification for segmentation of remotely sensedimages

An unsupervised classification technique conceptualized in terms of neural and fuzzy disciplines for the segmentation of remotely sensed images is presented. The process consists of three major steps: 1) pattern transformation; 2) neural classification; 3) fuzzy grouping. In the first step, the multispectral patterns of image pixels are transformed into what we call coarse patterns. In the second step, a delicate classification of pixels is attained by applying an ART neural classifier to the transformed pixel patterns. Since the resultant clusters of pixels are usually too keen to be of practical significance, in the third step, a fuzzy clustering algorithm is invoked to integrate pixel clusters. A function for measuring clustering validity is defined with which the optimal number of classes can be automatically determined by the clustering algorithm. The proposed technique is applied to both synthetic and real images. High classification rates have been achieved for synthetic images. We also feel comfortable with the results of the real images because their spectral variances are even smaller than the spectral variances of the synthetic images examined     

Effects of NH3 plasma passivation on N-channelpolycrystalline silicon thin-film transistors

The NH₃-plasma passivation has been performed on polycrystalline silicon (poly-Si) thin-film transistors (TFT's), It is found that the TFT's after the NH₃-plasma passivation achieve better device performance, including the off-current below 0.1 pA/μm and the on/off current ratio higher than 10⁸, and also better hot-carrier reliability than the H₂-plasma devices. Based on optical emission spectroscopy (OES) and secondary ion mass spectroscopy (SIMS) analysis, these improvements were attributed to not only the hydrogen passivation of the defect states, but also the nitrogen pile-up at SiO₂/poly-Si interface and the strong Si-N bond formation to terminate the dangling bonds at the grain boundaries of the polysilicon films. Furthermore, the gate-oxide leakage current significantly decreases and the oxide breakdown voltage slightly increases after applying NH₃-plasma treatment. This novel process is of potential use for the fabrication of TFT/LCD's and TFT/SRAM's     

双能X射线骨密度仪测定技术研究

以Ｌｕｎａｒ公司ＤＰＸ－Ｌ型双能Ｘ射线骨密度仪为例，研究引起测量误差的主要因素并提出质控措施。用自检模块、腰椎体膜评定仪器的体外测量精度好于１％。对１０位志愿者重复２次测量，体内精度对腰椎，ＭＰＤ（平均百分差）为０．４６，ＣＶ（变异系数）为０．７５；对股骨颈，ＭＰＤ为１．２６、ＣＶ为０．４７；Ｗａｒｄ’ｓ三角区ＭＰＤ为２．０１、ＣＶ为１．１４；大转子ＭＰＤ为１．６６、ＣＶ为０．７２。扫描图像由２位     

中央空调低温送风的系统设计方法

本文对中央空调低温送风系统的设计方法与常规空调进行比较，分析了低温送风系统设计中应该注意的问题，以使系统更节能、高效、合理。     

CARR水平孔道的设计特点

介绍了中国先进研究堆(CARR)水平孔道的用途、在堆本体的布置、水平孔道结构设计及设计方面的特点。     

乌江流域大型复杂水电站群联合优化调控关键技术及其应用研究

根据乌江流域总体规划、长江三峡以上防洪要求、南方电网运行特点、乌江流域水文特性等,贵州乌江水电开发有限责任公司组织开展了乌江梯级水库优化调度和发电优化控制的基本理论研究,并根据该研究建立了乌江流域水电站群联合优化调控系统,经过一系列优化调度规则、方法、措施在系统中的应用,实现了节水增发电的目的,取得了良好的社会经济效益。     

Enhanced Oil Recovery: The Synthesis of Anthraquinone [1, 2-C] Alkylisoxazole

Anthraquinone [1, 2-C] methylisoxazole is synthesized from 2-ethylanthraquinone through nitration and treating with oleum. The different methods of 2-ethylanthraquinone nitrated were discussed. The optimum conditions were determined. The structure of the product was confirmed by MS and ¹H NMR.