科技期刊编辑专业化和学者化是保证期刊学术质量的关键

一般科技期刊刊载的论文内容都具有很强的专业性,这就要求科技期刊编辑必须具有丰富的专业知识和较高的学术水平才能胜任编辑工作.从编辑过程的选题组稿、论文初审、选择审稿专家和编辑加工四个方面对此进行了阐述,指出了提高科技期刊编辑的相关专业知识和学术水平的措施.     

川中丘陵区一种新型小流域径流输沙模型的建立与应用

径流输沙模型对定量评价水沙的输出响应具有重要的意义。本研究在已有研究成果的基础上，通过对四川盐亭县林山西沟小流域的径流、泥沙进行现场观测与分析，提出含沙量单位线的定义及其确定方法，建立了适应该小流域的径流输沙模型。并应用实测资料进行比较，表明模型的模拟结果可靠，模拟过程确定性系数达0．8以上，为川中丘陵区小流域径流输沙过程的预测预报提供了一个新方法。     

乙炔在磁稳定床中的选择性加氢研究

 制备了一种磁性Pd/Al₂O₃催化剂，采用磁稳定床考察了活性组分负载量、反应条件及CO浓度对乙炔加氢反应性能的影响。结果表明，当反应温度80℃、反应压力1.5MPa、空速9000h－1、磁场强度（H）25kA/m时，乙炔转化率为100％，乙烯选择性可达81％，具有优良的乙炔加氢活性和乙烯选择性，优于相同反应条件下的进口催化剂；250h稳定性实验结果表明，磁性Pd/Al2O3催化剂具有良好的初活性和乙烯选择性，催化剂性能稳定。     

川东石炭系气藏排水采气工艺技术及其应用

四川盆地东部石炭系气藏是中国石油西南油气田公司的主力气藏之一，经过20多年的开发，出水气井增多、开发难度加大，必须进行排水采气才能维持正常生产。由于石炭系气藏大部分生产井存在井深、地层压力系数低、温度高、静液面深、复产后井口套压高的特点，常规排水采气工艺不能满足气藏的要求。针对这些难点，研究出深井高压气举、低压深井的优选管柱、深井高温泡排三项适合石炭系气藏的排水采气工艺，并在现场十多口井上进行了试验，增产效果显著。     

On the behavior of microstructures with multiple length scales

The current study aims to provide fundamental insight into the behavior of microstructures containing grain sizes that span multiple length scales. A commercial 5083 Al alloy was selected as the material of interest to facilitate comparison with recently published data. The materials studied here were prepared via the thermal consolidation of powders that were cryomilled for different times (i.e., 0, 2, 4, and 8 hours). Following consolidation, the resultant microstructure was characterized by an equiaxed grain morphology with a size distribution centered around 200∼300 nm. Dispersed among the 200- to 300-nm grains were coarse-grained regions or ligaments with a grain size ranging from 600 nm to 2 μm. The occurrence of coarse-grained regions is rationalized on the basis of recrystallization or subgrain coarsening, whereas the occurrence of equiaxed fine regions is proposed to be a result of continuous grain growth. Two types of microstructures were selected for study, containing coarse-grained volumes of approximately 28 pct and 43 pct that corresponded to an ultimate tensile strength (UTS) of 566 MPa and 535 MPa, and a fracture strain of 3.2 pct and 3.5 pct, respectively. The observed ductility and the relevant toughening mechanisms were discussed in light of the presence of multiple length scales.     

碘量法测铜中物质性质和分析操作

本文讨论了碘量法测定铜量中一些有关物质的特性,以及这些性质对分析条件和操作的要求。     

Ta-2．5W焊接工艺试验研究

通过对Ta-2.5W难熔重金属换热管的一系列焊接工艺试验研究,掌握了钽材的特殊焊接技术工艺和要求,满足了今后制造和修复苯胺装置中硫酸蒸发器管束的需要。     

Mechanical properties of iron processed by severe plastic deformation

In the present study, the mechanical properties of Fe processed via severe plastic deformation (equal-channel angular pressing (ECAP)) at room temperature were investigated for the first time. The grain size of annealed Fe, with an initial grain size of about 200 μm, was reduced drastically during ECAP. After eight passes, the grain size reaches 200 to 400 nm, as documented by means of transmission electron microscopy (TEM). The value of microhardness during pressing increases 3 times over that of the starting material after the first pass and increases slightly during subsequent pressing for higher-purity Fe. Examination of the value of microhardness after eight passes as a function of post-ECAP annealing temperature shows a transition from recovery to recrystallization, an observation that resembles the behavior reported for heavily deformed metals and alloys. The tensile and compression behaviors were examined. In tension, a drop in the engineering stress-engineering strain curve beyond maximum load was observed both in the annealed Fe and the ECAP Fe. This drop is related to the neck deformation. The fracture surface, examined by scanning electron microscopy (SEM), shows vein patterns, which is different from the dimples found on the fracture surface of annealed Fe. In compression, an initial strain-hardening region followed by a no-strain-hardening region was observed in the ECAP Fe. The yield strength in tension of the ECAP Fe was observed to be higher than that in compression. The strengthening mechanisms and softening behavior are discussed.     

钢样成分化验分析结果网络传输系统的开发与应用

钢样成分化验分析结果网络传输系统将碳硫分析仪、光谱分析仪和相应的计算机控制系统按以太网络结构组联,形成"炉前分析网络",采用分析网主服务器系统软件和网络分析系统软件实现网络传输。该系统可将炉前钢样化验分析结果实时传输到炉前大屏,具有传输速度快、准确率高的特点,提高了工作效率和产品合格率,降低了生产成本。     

长庆油田苏平1井固井技术研究与应用

苏平l井完井方式运用了技术套管一次上返、悬挂尾管和筛管技术。该井技术套管段井眼大、裸眼段长，加上大斜度、小间隙的尾管段．对水泥浆体系的性能要求较高。总结分析了长庆天然气水平井苏平l井的固井技术问题，介绍了苏平l井的井身结构与地层性质。通过研究．确定采用低失水GSJ水泥浆体系。该体系成功地应用在三次工程建井过程中，解决了长裸眼、大灰量、大斜度、尾管小间隙等固井技术问题。固井质量达到工程要求。