Preparation of nanosized titania powder via the controlled hydrolysis of titanium alkoxide

By controlling the hydrolysis of titanium butoxide, followed with or without an ethanol washing process, the preparation of nanoscale titania powder was studied in detail. The characteristics of different powders produced by the direct precipitation (without an ethanol wash) and ethanol wash processes were studied by X-ray diffraction, transmission electron microscopy, BET, thermogravimetry and differential thermal analysis techniques. By comparison, it was found that both the direct precipitation and ethanol wash methods can obtain slightly agglomerated nanoscale titania powders of less than 15 nm, but the ethanol wash can further reduce the agglomeration. The particle sizes of titania powders can be modified while still retaining the anatase structure.     

Effect of processing history on the properties of Ag-based tapes

The Bi-system tapes and coils were prepared by the powder-in-tube method. The effect of processing and heat treatment on the properties of the tapes and coils was studied. It is found that the shearing stress produced by the rolling process may destroy the 2223 phase, and the destroyed 2223 phase cannot be recovered by heat treatment, whereas the pressing stress produced by the uniaxial pressing process only makes the 2223 phase grains break, and the broken 2223 phase can be closed by the heat treatment. TheJ _c values of the rolling samples, pressing sample, and the coil with a diameter of 35 mm are over 1.3×10⁴, 2.5×10⁴, and 4×10³ A/cm² (77 K, 0 T), respectively.     

造纸机集散控制系统

本文介绍了造纸机集散控制系统．讨论了其硬件的组成和软件结构．研究了ＤＤＳ过程级控制器的功能及对造纸机各分部速度的优化控制．系统投人运行后，取得较好的经济效益．     

FEATURE SOLID MODELING TOOL SYSTEM:FSMTS

In conformity with the principle of Design for Manufacture,feature-based design strate-(?)es have been developed.As the“feature”is relevant to the“macro process plan”and“macro NCprograms”,obviously,“feature”is beyond the power of conventional solid modellers.Neverthe-less,substantial breakthrough has not been made in the solid modeling field,except“feature at-taching”or“feature recognizing”methods have been taken on.In this paper,the theory,concepts,system architecture,and algorithm principles of solid modeling tool system have beenrepresented.The practice of Feature Solid Modeling Tool System (FSMTS) developed atHuazhong University has proved that the tool may be a new foundation of Feature-Based Design.     

一种制备插层和无定形高岭土的新方法

利用甲醇钠强烈的夺氢作用 ,介绍了一种制备插层和无定形高岭土的方法。利用XRD为主要检测手段研究了甲醇钠的质量分数、反应温度等因素对反应的影响。结果表明 :在反应温度较低、质量分数较低的甲醇钠溶液中 ,高岭土容易被插层而膨胀 ,反之高岭土的层状结构被破坏而无定形化。红外光谱分析进一步证明了插层和无定形高岭土结构的变化     

三相四线统一电能质量调节器的控制策略

针对电网输入电压的不平衡、非正弦及负载的不平衡、非线性特性，提出了一种基于三相静止坐标系下的三相四线统一电能质量调节器（UPQC）的协调控制策略。该策略将UPQC的串联变流器控制为基波正弦电流源，而并联变流器控制为基波正弦电压源，从而实现了三相四线UPQC对电能质量的综合控制能力，既改善了电网侧的电能质量问题，实现了电网输入电流的正弦及单位输入功率因数，也改善了负载侧的电能质量问题，实现了负载电压的平衡、额定及正弦。10 kVA系统实验装置的实验结果表明了该控制策略的有效性。     

丹江口工程大坝加高后的几个水力学问题

依托1∶100水工模型试验成果,重点介绍了丹江口大坝加高后的几个水力学问题如泄流能力、坝面压力特性、河床局部冲刷、下游河道流速流态、泄洪对电厂及航运的影响等.研究显示:大坝加高后泄流能力可满足设计要求,坝下河床冲刷加重,挑距加远,设计洪水22 300 m3/s时坝下冲坑最低点高程为43.0 m,各级泄量冲坑上游坡均缓于临界坡,也略缓于初期工程同级流量冲坑的上游坡;坝下600 m以内为护岸工程重点防护段,岸边流速为5.8～9.8 m/s;泄洪对丹江口电厂影响较小,对自备电站不利影响较为显著;最大通航流量6 200 m3/s时下游引航道口门区流态复杂,水流较混乱.     

冷凝器中弓形折流板结构与两相流诱发的振动

根据两相流体诱发振动的机理与相关公式,对在两相流状态下运行的稀醋酸酐冷凝器进行了振动分析,结果表明,采用双弓形折流板可有效地防止换热器的振动。     

瓦斯燃烧器回流区测试

燃烧器流场内回流区的大小和形状决定了燃烧火焰的稳定性 ,利用APV激光测速系统 ,在燃烧器冷态测试实验装置上对一瓦斯燃烧器冷态模型的流动进行了研究 ,发现了该燃烧器流场内的双回流区结构 ,并得到了中心回流区尺寸与稳焰器结构的关系 ,为该结构类型燃烧器的稳焰设计及稳焰能力的评价提供了实验依据     

双功率谱干涉实现图像识别

提出一种新的图像识别方法 ,直接利用输入图像和参考图像的联合变换相关功率谱进行双功率谱干涉 ,不需要特殊的光学元件 ,也不需要对功率谱进行调制和改造。实验表明 ,相同图像的双功率谱干涉出现明显的条纹 ,而不同图像则几乎不出现干涉条纹。