Tocopherol contents of some Turkish wine by-products

The aim of this study was to determine the tocopherol contents of wine by-products including grape seed, pomace (seed, skin and stem) and bagasse (skin and stem) by using two different extraction methods in order to evaluate the possibilities of them as natural non-polar antioxidants. Cold extraction appeared to give more tocopherol contents in seeds than hot extraction. But hot extraction was found more suitable for pomace and bagasse. α-Tocopherol was the most abundant tocopherol in the grape seed, pomace and bagasse. Although γ- and δ-tocopherols were found in the samples with low concentrations, β-tocopherol was not detected in the samples. Kalecik karası had the highest α and total tocopherol compared to the other cultivars. On the other hand, hot extracted bagasse in all cultivars gave the highest tocopherol contents. As a conclusion, wine by-products, a large scale wastes, can be evaluated both to get natural tocopherol source and to obtain economical gain.     

Tensile,creep, and low-cycle fatigue behavior of a cast γ-TiAl-based alloy for gas turbine applications

The influence of chemical composition on the microstructure of the γ-titanium aluminide alloy Ti-48Al-2W-0.5Si (at. pct) and the accompanying tensile, low-cycle fatigue, and creep properties has been evaluated. The study showed that small variations in chemical composition and casting procedures resulted in considerable variations in the microstructure, yielding vastly different mechanical properties. Low contents of aluminum and tungsten led to a coarse-grained lamellar (γ/α ₂) microstructure with high creep resistance. A composition close to the nominal one produced a duplex (γ+γ/α ₂) structure with favorable strength, ductility, and low-cycle fatigue properties. By controlling the solidification and cooling rates at casting, a pseudoduplex (PS-DP) microstructure with a unique combination of high strength and high fatigue and creep resistance can be obtained. These unique properties can be explained by the diffuse boundaries between the relatively small γ grains and the neighboring lamellar colonies, combined with semicoherent interfaces between the γ and α ₂ phases. At tensile and low-cycle fatigue loading, these boundaries act like high-angle boundaries, producing a virtually fine-grained material promoting strength, whereas at creep loading, grain-boundary sliding is hindered in the semicoherent interfaces leading to high creep resistance.     

Crystallographic electron microscopy

We present a family of techniques for the transmission electron microscope that generate surface zone-axis patterns. These patterns display the variation of the diffracted-beam intensity as a function of the angle of the incident electrons. The conditions of the experiments are those of reflection high-energy electron diffraction at near grazing incidence. The techniques are: surface convergent-beam diffraction, a surface analogue of the Tanaka method and a modified double-rocking scheme. Experimental results are presented for diffraction from surfaces of MgO and MoS₂. We anticipate that surface zone-axis patterns (surface ZAPs) will become established as an important tool for surface characterization, especially when used in conjunction with high-resolution surface imaging and surface energy loss spectroscopy; surface ZAPs may be expected to play, in surface analysis, a role analogous to that played by convergent-beam diffraction in normal transmission electron microscopy.     

Putting it all together – Formal verification of the VAMP

In the verified architecture microprocessor (VAMP) project we have designed, functionally verified, and synthesized a processor with full DLX instruction set, delayed branch, Tomasulo scheduler, maskable nested precise interrupts, pipelined fully IEEE compatible dual precision floating point unit with variable latency, and separate instruction and data caches. The verification has been carried out in the theorem proving system PVS. The processor has been implemented on a Xilinx FPGA. A shorter version of this article with the title “Instantiating uninterpreted functional units and memory system: functional verification of the VAMP” appeared in [8]. The work reported here was done while all the authors were with Saarland University.     

Hydrogenation of canola oil in the presence of nickel and the methyl benzoate-chrome carbonyl complex

Canola oil was hydrogenated using a mixture of homogeneous methyl benzoate-Cr(CO)₃ and heterogeneous nickel catalysts. The effect of the methyl benzoate-Cr(CO)₃_to-nickel ratio on the activity, specific isomerization index, linoleate and linolenate selectivities, and fatty acid composition was evaluated, and the results compared with those obtained with commercial nickel catalyst and methyl benzoate-Cr(CO)₃ used individually. At higher chromium-to-nickel ratios the activity of nickel was inhibited and the system behaved essentially like the pure chrome complex, while at low chromium-to-nickel ratios the characteristics of the nickel predominated. In a short transition zone relatively high reaction rates were obtained with significantly reducedtrans-isomer levels in the product. In a broader sense, it may be possible to combine a homogeneous and heterogeneous catalyst while retaining the advantages of both. We may thus be able to design catalyst systems for specific applications.     

Effect of specimen size and loading conditions on spalling of concrete

Different qualities of concrete have been fire tested using different geometries of the specimens as well as different load levels and load configurations. The main objective with the study was to examine a test methodology consisting of a full‐scale test and different small scale‐tests for determining the probability of spalling and the amount of spalling of fire exposed concrete structures. A reference specimen was defined as a one‐sided fire exposed slab with the dimensions 1800 × 1200 mm² giving an exposed area of 1500 × 1200 mm². A number of concrete qualities with different probabilities for spalling, were tested using the reference specimen. These tests showed that the reference specimens worked well giving the expected test results. Small specimens were manufactured in different shapes with the same concrete as the one used in the reference tests. These small specimens were tested either at the same time as the reference specimens in the large furnace or afterwards on a small‐scale furnace where the fire exposed surface was 450 × 360 mm². The test results clearly show the increased probability and the increased amount of spalling by using external compressive loading. The results also show that by using pre‐stress through bars or wires the load can be lost due to heating of the bars/wires which results in a decreased amount of spalling. The boundary of the specimen also affects the amount of spalling. The spalling around the edges was in all tests less than the spalling on the central parts of the exposed area. It could also be noted that the spalling did not pass completely through any of the specimens. The reason for this is probably that the water/vapour could migrate out from the unexposed surface of the specimen. Copyright © 2006 John Wiley & Sons, Ltd.