Application of differential quadrature to static analysis of structural components

The numerical technique of differential quadrature for the solution of linear and non-linear partial differential equations, first introduced by Bellman and his associates, is applied to the equations governing the deflection and buckling behaviour of one- and two-dimensional structural components. Separate transformations are used for higher-order derivatives, as suggested by Mingle, thus extending the method to treat fourth-order equations and to include multiple, boundary conditions in the respective co-ordinate directions. Results are obtained for various boundary and loading conditions and are compared with existing exact and numerical solutions by other methods. The application of differential quadrature to this class of problems is seen to lead to accurate results with relatively small computational effort.     

A Web‐based and Group Learning Environment for Introductory Environmental Engineering

The use of computer‐based technology is becoming more prevalent in the classroom. As a part of an educational research project sponsored by the GE Foundation, strategies for augmenting a course, Introduction to Environmental Engineering (CE 280), were investigated including cross‐disciplinary experiences in teamwork, design, and the use of advanced teaching technologies such as the web. Interactive tools to assist student learning were developed and refined. Efforts have focused on developing an extensive website, web‐based quizzes and homework assignments, and tutorials. Base groups were used to provide both intellectual and emotional support to students. This paper summarizes the development of this course and the impact of rapid feedback on the progression of student understanding.     

On the influence of N on residual microstrain in cryomilled Ni

The factors that influence the development of residual microstrain during milling in a liquid nitrogen atmosphere, defined hereafter as cryomilling, are investigated. The residual microstrains in cryomilled Ni, processed under various cryomilling conditions, were examined by X-ray diffraction (XRD) and analyzed through the single line approximation (SLA) method. The average residual microstrains are determined to be in the range of 2×10⁻³ to 6×10⁻³. The residual microstrain on the (200) plane is higher than those on the other planes by 33 pct. The residual microstrain and its anisotropy in Ni are reduced after heat treatment at 800 °C for 1 hour. The measured microstrain is proposed to evolve from the presence of N and O as impurity atoms in the Ni lattice. Both N and O are introduced from the environment and then their solubility in Ni is enriched via the generation of defects that occurs during cryomilling. The stable site for N and O atoms in Ni is the octahedral site, and the sizes of N and O atoms exceed those of the octahedral site of Ni by 48 and 16 pct respectively. Accordingly, a lattice strain field is expected around interstitial N atoms that are located at octahedral sites. By comparing the crystal structure around the octahedral site, the stable site for impurity N atoms, in the Ni lattice with that of Ni₃N structure, the lattice strains are estimated to be in the range of 5 to 15 pct. The result shows that the (200) plane has strains that are 2 times higher than those in other planes, and this is argued to be the reason for the measured anisotropy of residual strain in Ni after cryomilling.     

Glass fiber-filled thermoplastics. I. Wall and processing effects on rheological properties

A systematic study of wall effects on the shear viscosity of short glass fiber-filled polypropylene and polystyrene is presented. The dependence of these effects on capillary radius, shear rate, temperature, and polymer matrix is examined. The “true” viscosity curves of these materials (free from wall effects) can be obtained by an extrapolation procedure. Breakage of glass fibers in the high shear-rate processes of extrusion and injection molding lead to an appreciable reduction of the viscosity of these materials and is probably the more important effect to take into account in these processes.     

Proton-exchange optical waveguides in Z-cut LiNbO/sub 3/ using toluic acid

Proton-exchanged planar waveguides were demonstrated in Z-cut LiNBO/sub 3/ using toluic acid as a new organic proton source. These waveguides exhibit a propagation loss of around 1 dB/cm, and a step refractive index profile with an index increase of 0.124 measured at 0.663 mu m. The diffusion rate was found to be lower than those obtained using the popular benzoic and phosphoric acids.<>     

Effect of bulk flow pulsations on film cooling with compound angle holes

Experiments are conducted to investigate the effects of bulk flow pulsations on film cooling with compound angle holes. A row of five film cooling holes is considered with orientation angles of 0°, 30°, 60°, and 90° at a fixed inclination angle of 35°. Static pressure pulsations are produced by an array of six rotating shutter blades, which extend across the span of the exit of the wind tunnel test section. The pulsation frequency is fixed at 36 Hz, but changes in the time-averaged blowing ratios of 0.5, 1.0 and 2.0 produce three different coolant Strouhal numbers, 3.6, 1.8 and 0.9, respectively. Detailed film cooled boundary layer temperature distributions are measured by a cold wire and the adiabatic film cooling effectiveness by thermochromic liquid crystal (TLC). The boundary layer temperature surveys show that pulsations induce large disruptions to the boundary layer temperature distribution and the film coverage. As the orientation angle increases, the injectant concentration spreads further into the spanwise direction because of pulsations than the steady case. With pulsations the adiabatic film cooling effectiveness value decreases regardless of the orientation angle. The amount of reduction, however, depends on the orientation angle in such a way that the larger the orientation angle is, the smaller the reduction is.     

Enhancement of oxide break-up by implantation of fluorine inpoly-Si emitter contacted p+-n shallow junctionformation

In this study, it is demonstrated that the incorporation of fluorine can enhance poly-Si/Si interfacial oxide break-up in the poly-Si emitter contacted p⁺-n shallow junction formation. The annealing temperature for breaking up the poly-Si/Si interfacial oxide has been found to be as low as 900°C. As a result, the junction depth of the BF₂-implanted device is much larger than that of the boron-implanted device     

Effects of hot carrier induced interface state generation insubmicron LDD MOSFET's

A two-dimensional numerical simulation including a new interface state generation model has been developed to study the performance variation of a LDD MOSFET after a dc voltage stress. The spatial distribution of hot carrier induced interface states is calculated with a breaking silicon-hydrogen bond model. Mobility degradation and reduction of conduction charge due to interface traps are considered. A 0.6 μm LDD MOSFET was fabricated. The drain current degradation and the substrate current variation after a stress were characterized to compare the simulation. A reduction of the substrate current at V_g ≃0.5 V_d in a stressed device was observed from both the measurement and the simulation. Our study reveals that the reduction is attributed to a distance between a maximum channel electric field and generated interface states     

A circular crossed-field amplifier for in situ measurements, studyof reentrant beam effects, and comparison with numerical simulation

A low frequency, injected beam, circular format crossed-field amplifier has been designed and constructed for the purpose of studying electron-radio frequency wave interaction in reentrant devices. The device has been designed to allow in situ diagnostic probe measurements in the space between the anode and sole. The device has been operated in nonreentrant, fully reentrant, and reentrancy controlled configurations. Details of the design and operating parameters are described. Device characteristics are examined with respect to the amount of circulating charge or degree of reentrancy. A large increase in gain has been achieved from nonreentrant to the fully reentrant format. A gain of 7.2 dB has been obtained for the latter whereas only 3.8 dB has been obtained for the former with 30 mA of injected beam current. A maximum gain of 14.4 dB has been achieved for the fully reentrant configuration. Electron beam and noise measurements versus the degree of reentrancy have also been examined. Results from the nonreentrant amplifier performance have been directly compared with the MASK simulation code and good agreement has been obtained. These experiments will provide the basis for more detailed investigations on the effect of reentrancy on CFA operation and will also allow for the development of more accurate computer models of the reentrant system for numerical simulation of CFA operation