Be radioactive beam production at CIRCE and its utilization in basic and applied physics

A pure ⁷Be beam with an energy E = 1-8 MeV is available for nuclear and applied physics at the 3 MV Pelletron tandem accelerator CIRCE in Caserta. The beam is produced using an offline technique. Typical analyzed beam intensities are about 2 ppA, using cathodes with an activity of the order of 200 MBq. The ⁷Be implantation has been used for both fundamental nuclear physics and applied physics. In particular, different metals have been implanted with ⁷Be in order to study the influence of the chemical composition and of the number of quasi-free electrons of the host material on the ⁷Be half-life. In the field of applied physics, the ⁷Be implantation turns out to be very interesting for wear measurement. In fact, in this case ⁷Be is used as a depth-sensitive tracer. The continuous detection of the sample activity during the wear allows a high sensitivity measurement of wearing speed. The ⁷Be beam production at CIRCE, the implantation procedure and the results obtained from the ⁷Be half-life measurements and the wear characterization of implanted steel samples are described.     

On measuring nondeterminism in regular languages

It is well known that allowing nondeterminism in a finite automaton can produce in the most extreme case an exponential savings in the number of states required to recognize a regular language. This paper studies situations intermediate between forbidding nondeterminism and allowing it. The amount of nondeterminism used by a finite automaton is quantified, so that the decrease in the size of the state space that occurs as the amount of nondeterminism that is permitted increases in increments can be studied. These intermediate situations are shown always to lie between two extremes:(1) there are no savings as the amount of nondeterminism increases incrementally, so that savings occur only when the amount of nondeterminism becomes unlimited;(2) each increment of nondeterminism results in additional savings, the number s of states decreasing approximately as s^1/i, until exponential savings have been achieved after about i = logs/log log s increments.     

Semiempirical thermodynamic modeling of a direct methanol fuel cell system

In this study, a thermodynamic model of an active direct methanol fuel cell (DMFC) system, which couples in‐house experimental data for the DMFC with the mass and energy balances for the system components (condenser, mixing vessel, blower, and pumps), is formed. The modeling equations are solved using the Engineering Equation Solver (EES) program. This model gives the mass fluxes and thermodynamic properties of fluids for each state, heat and work transfer between the components and their surroundings, and electrical efficiency of the system. The effect of the methanol concentration (between 0.5 and 1.25 M) and air flow rate (between 20 and 30 mL cm^?2 min^?1) on the net power output and electrical efficiency of the system and the condenser outlet temperature is investigated. The results essentially showed that the highest value for the electrical efficiency of the system is 23.6% when the current density, methanol concentration, and air flow rate are taken as 0.2 A cm^?2, 0.75 M, and 20 mL cm^?2 min^?1, respectively. In addition, the air flow rate was found to be the most significant parameter affecting the condenser outlet temperature.     

Network formation by aza‐Michael addition of primary amines to vinyl end groups of enzymatically synthesized poly(glycerol adipate)

A highly efficient approach for the synthesis of polyester‐based networks via aza‐Michael addition of primary amines to α,β‐unsaturated (vinyl) end groups of poly(glycerol adipate) (PGA) was achieved. By acylation of PGA with 6‐(Fmoc‐amino)hexanoic acid side chains via Steglich esterification, protected amine‐functionalized PGA was obtained. This was followed by the removal of fluorenylmethyloxycarbonyl (Fmoc) protecting groups and the synthesis of PGA‐based networks under catalyst‐free conditions. The successful conjugate addition of primary amines to vinyl end groups and network formation were confirmed using ¹³C magic angle spinning NMR and Fourier transform infrared spectroscopy. Network heterogeneity and defects were quantitatively investigated using ¹H double‐quantum NMR spectroscopy. Finally, a hydrogel was prepared with potential biomedical applications.     

Steels for pipes and pipelines

The development of steel grade up to X 80 quality was shown explaining metallurgical mechanisms used for thermomechanically rolled steels with improved toughness behaviour. The influence of the reduction of C-content for these TM-steels on the field welding behaviour was discussed. The development of steels with improved resistance against sour media was presented, showing the influence of purity degree, Mn- and C-content in combination with the steelmaking practice. The influence of residual stress on the SSCC resistance of SAW pipe was pointed out and a heat treatment process was presented reducing the residual stress and resulting in crack free spiral welded pipes under the most severe test condition of NACE-solution with pH-values of 2.7–3.5.     

Homogeneity analysis of square meter-sized electrodes for PEM electrolysis and PEM fuel cells

Electrodes for polymer electrolyte membrane electrolyzers and fuel cells are manufactured by coating a catalyst dispersion, consisting of precious metal, ionomer and solvents, onto a substrate that is subsequently dried. One target of current research is to produce square meter-sized electrodes, but so far the homogeneity that can be achieved in this scaling is unclear. To quantify the achievable homogeneity of an electrode, manufactured by means of slot die coating in a roll-to-roll pilot plant, this study focuses first on the selection of an appropriate substrate by investigating thickness, basis weight and surface free energy distribution at the square meter scale. Afterward, a dispersion is coated on the selected substrate, dried and investigated with respect to thickness and basis weight distribution. Among the investigated substrates, Kapton has the smallest scatter in terms of thickness and basis weight. The subsequent coating results in a precious metal loading of 1.10 mg cm\(^{-2}\), with a scattering of 5.5% that can be further reduced to 4.5% when edge effects can be prevented. These results are now available for further research in which it is necessary to investigate whether or not these fluctuations affect the achievable electrochemical efficiencies of electrodes.