Quantitative analysis of ephedrines in urine by HPLC

Simultaneous determination of six ephedrines in urine sample has been achieved by high performance liquid chromatography on a Lichrospher RP-18 column, using methylamphetamine as internal standard. The 6 ephedrines are well separated in 25 minutes with resolution better than 1.8. This method has high recovery, selectivity and reproducibility, and the linearity is satisfactory from 1.5 micrograms/ml to 25 micrograms/ml with correlation coefficients better than 0.999.     

Cd-ZSM-5沸石催化剂的制备、表征和芳构化催化性能

采用离子交换、浸渍和混合三种方法制备镉改性ZSM-5沸石催化剂,考察了改性方法和镉含量对催化剂的表面酸性和Cd状态以及芳构化性能的影响。结果表明,加入镉降低了B酸性,Cd~(2+)与沸石结合形成了L_(1612)酸中心,其生成量取决于改性方法和Cd含量,并与芳构化活性提高有直接关系。     

Clinical study in epidural injection with lappaconitine compound for post-operative analgesia

In this study, the effect and side-effect of epidural injection with lappaconitine compound for post-operative analgesia was observed. One hundred and twenty patients were randomly divided into 4 groups. Lappaconitine compound (LB) consisted of 12 mg of lappaconitine and 22.5 mg of bupivacaine, was given to group A (the group of observation), and lappaconitine 12 mg, bupivacaine 22.5 mg and morphine 2 mg to group B, C and D respectively for control. All were given by epidural injection with single blind method during post-operative pain of incision operation. Result showed that the initiating of analgesia was quicker in group A and C than that in group B and D, and the efficacy was group D > A > C > B. There was significant difference between group A and B in the above two parameters, P < 0.01 and P < 0.05. The analgisia maintenence time of single injection was D > A > B > C, that of group D was significantly longer than that of group A (P < 0.01). It indicated that the epidural injection with LB was more rapid and potent than that with lappaconitine alone in post-operative analgesia, and the former had no side-effect, it was safer than morphine.     

具有阻力特性材料的σ_f－σ关系及一种新的阻力曲线测定方法

通过对相变增韧陶瓷及一种可切削玻璃－陶瓷动态疲劳（恒应力速率）试验中高应力速率区断裂应力下降现象的理论分析，发现这种现象与材料的阻力特性（Ｒ－ｃｕｒｖｅ）密切相关。确立的σ_ｆ－σ理论关系能够很好地描述整个应力速率区间内的动态疲劳试验结果。高应力速率区σ_ｆ－σ在双对数坐标下为负斜率直线，直线斜率为（ｍ为阻力曲线ＫＲ＝ｋ（△ａ）~ｍ的指数），断裂主要由材料阻力行为控制；低应力速率区，σ_ｆ－σ在双对数坐标下为正斜率直线，直线斜率为　（ｎ为应力腐蚀指数），断裂主要由材料应力腐蚀行为控制。建立了测定材料阻力特性的一种新方法，分别用这种方法及压痕／弯曲方法对一种可切削玻璃－陶瓷的阻力特性进行了实验测定，两种方法所得结果有很好的一致性。     

Mullite Formation by Endothermic Reaction of α-Alumina/Silica Microcomposite Particles

The formation of mullite was investigated using microcomposite powders which consist of α-alumina cores and amorphous silica coatings. Differential thermal analysis and X-ray diffraction showed that the mullitization reaction was endothermic. In contrast, mullite forms exothermically in samples prepared by sol-gel processing. The results are shown to be consistent with available thermodynamic data for mullite formation from different alumina and silica phases.     

Fabrication of 1.55 μm VCSELs on Si using metallic bonding

Using AuGeNiCr multilayered metals as the wafer bonding medium, long-wavelength GaInAsP/InP vertical cavity surface emitting lasers employing Al-oxide/Si as the upper and lower distributed Bragg reflectors were fabricated on Si substrate with the bonding interface formed outside the vertical cavity surface emitting laser cavity. Laser emission at 1.545 μm was measured under pulsed operations near room temperature. The low-temperature metallic bonding process demonstrates a great potential in device fabrication     

Retrievals of column water vapor using millimeter-wave radiometric measurements

The airborne Millimeter-wave Imaging Radiometer (MIR) measurements conducted over the Midwest region of the continental United States during January/February 1997 and over the Alaska-Arctic region during May 1998 are used to estimate column water vapor W<0.8 g/cm/sup 2/ under a clear sky. On board the same aircraft are two other instruments, the Cloud Lidar System (CLS) and MODerate-resolution Imaging Spectrometer (MODIS) Airborne Simulator (MAS), which provide cloud cover information and independent measurements of W, respectively. The MIR-estimated W values are compared and found to be in very good agreement with those measured by rawinsondes at near concurrence. A close correlation is found between the MIR-estimated W and that estimated from the MAS near-IR reflectance ratios. Water surface emissivities at several MIR frequencies are obtained in the process of the W retrieval from several flights over the Midwest lakes. These estimated emissivities compared favorably with values calculated for a calm water surface, which are based on a di-electric permittivity model and MAS-measured surface temperatures. The results from all comparisons strongly demonstrate the soundness of the technique for estimating W.     

菱镁矿固硫特性的理论分析

对菱镁矿在固体燃料燃烧过程中的固硫特性进行了理论研究，所得结论对进一步将菱镁矿作为固体燃料燃烧过程中的固硫剂具有非常重要的意义。     

On the corrosion fatigue crack initiation model and expression of metallic notched elements

In the present study, attempts are made to extend the application of the mechanical model for the fatigue crack initiation (FCI) and the FCI life formula of metallic notched elements in laboratory air to those in the corrosive environment. The test results and analysis of the corrosion FCI (CFCI) life of aluminum alloys and Ti---6A1---4V show that the expression of the CFCI life obtained by modifying the FCI life formula in laboratory air can give a good fit to the test results of the CFCI life. The salt water (3.5% NaCl) environment has no effects on the CFCI resistant coefficient compared with the FCI resistant coefficient in laboratory air. However, 3.5% NaCl environment greatly decreases the CFCI threshold of aluminum alloy, but has little effect on the CFCI threshold of Ti---6A1---4V. The loading frequency ranging from 1 Hz to 10 Hz has no appreciable effect on the CFCI life, and thus, the CFCI threshold of aluminum alloys investigated. Hence, the expression for the CFCI life of metallic notched elements proposed in this study is a better one, which reveals a correlation between the CFCI life and the governing parameters, such as, the geometry of the notched elements, the nominal stress range, the stress ratio, the tensile properties and the CFCI threshold. However, this new expression of the CFCI life needs to be verified by more test results.