镍层耐硝酸腐蚀性测试——一种简单的预先探测ENIG镍层“黑盘”现象的测试方法

随着更加精细的SMT、BGA等表面贴装技术的运用,化学沉镍金(ENIG)作为线路板最终表面处理得到了越来越广泛的应用,同时可怕的“黑盘”现象也随之更广泛地“流行”起来,直接导致贴装后元器件焊接点不规则接触不良。为了贯彻执行最好的流程控制和采取有效的预防措施,了解这种焊接失败的产生机理是非常重要的,及早的观测到可能发生“黑盘”现象的迹象变得同样关键。本文介绍了一种简单的预先探测ENIG镍层“黑盘”现象的测试方法-镍层耐硝酸腐蚀性测试,这种测试可以用于作为一种常规的测试方法监测一般化学沉镍溶液在有效使用寿命范围内新鲜沉积的镍层的质量。利用Weibull概率统计分析在不同的金属置换周期(MTO)下镍层的可靠性能表现。结合试验结果得出了一个镍层耐硝酸腐蚀性的判定标准。     

A three-dimensional FE analysis of large deformations for impact loadings using tetrahedral elements

 A three-dimensional dynamic program for the anaysis of large deformations in contact-penetration problems is developed using the finite element Lagrangian method with explicit time integration. By incorporating a tetrahedral element, which allows a single-point integration without a special hourglass control scheme, this program can be more effective to the present problem. The position code algorithm is used to search contact surface. Eroding surfaces are also considered. The defense node algorithm was slightly modified for the calculation of contact forces. A study of obliquity effects on metallic plate perforation and ricochet processes in thin plates impacted by a sphere was conducted. It is well simulated that on separation of two parts of the sphere, the portion still within the crater tends to perforate, while the portion in contact with the plate surface ricochets. This deformation pattern is observed in experiments, especially at high obliquities. A long rod that impacts an oblique steel plate at high impact velocity was also simulated in order to study the dynamics of the rod caused by the three dimensional asymmetric contact. The agreement between simulated and experimental results is quite good. Fracture phenomena occuring at high obliquity deserves further investigations. Received: 20 February 2002 / Accepted: 20 September 2002     

Measurement and numerical simulation of three‐dimensional fiber orientation states in injection‐molded short‐fiber‐reinforced plastics

To determine three‐dimensional fiber orientation states in injection‐molded short‐fiber composites, a confocal laser scanning microscope (CLSM) is used. Since the CLSM optically sections the specimen, more than two images of the cross sections on and below the surface of the composite can be obtained. Three‐dimensional fiber orientation states can be determined by using geometric parameters of fiber images obtained from two parallel cross sections. For experiments, carbon‐fiber‐reinforced polystyrene is examined by the CLSM and geometric parameters of fibers on each cross‐sectional plane are measured by an image analysis. In order to describe fiber orientation states compactly, orientation tensors are determined at different positions of the prepared specimen. Three‐dimensional orientation states are obtained without any difficulty by determining the out‐of‐plane angles utilizing fiber images on two parallel planes acquired by the CLSM. Orientation states are different at different positions and show the shell–core structure along the thickness of the specimen. Fiber orientation tensors are predicted by a numerical analysis and the numerically predicted orientation states show good agreement with measured ones. However, some differences are found at the end of cavity. They may result from the fountain flow effects, which are not considered in the numerical analysis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 500–509, 2003     

Development of geometrically exact new shell elements based on general curvilinear co‐ordinates

In the present study first‐order shear deformable shell finite elements based on general curvilinear co‐ordinates are proposed. For the development of the present shell elements, a partial mixed variational functional with independently assumed strains is provided in order to avoid the severe locking troubles known as transverse shear and membrane lockings. Bubble functions are included in the shape function of displacement to improve the performance of the developed element. The proposed assumed strain four‐ and nine‐node elements based on the general tensor shell theory provide an efficient linkage framework for shell surface modelling and finite element analysis. In the several benchmark problems, the present shell elements with exact geometric representations demonstrate their performance compared to previously reported results. Copyright © 2002 John Wiley & Sons, Ltd.     

Enhanced thermal stability of a sputtered titanium-nitride film as a diffusion barrier for capacitor-bottom electrodes

The effect of a thin RuO_x layer formed on the Ru/TiN/doped poly-Si/Si stack structure was compared with that on the RuO_x/TiN/doped poly-Si/Si stack structure over the post-deposition annealing temperature ranges of 450–600°C. The Ru/TiN/poly-Si/Si contact system exhibited linear behavior at forward bias with a small increase in the total resistance up to 600°C. The RuO_x/TiN/poly-Si/Si contact system exhibited nonlinear characteristics under forward bias at 450°C, which is attributed to no formation of a thin RuO_x layer at the RuO_x surface and porous-amorphous microstructure. In the former case, the addition of oxygen at the surface layer of the Ru film by pre-annealing leads to the formation of a thin RuO_x layer and chemically strong Ru-O bonds. This results from the retardation of oxygen diffusion caused by the discontinuity of diffusion paths. In particular, the RuO_x layer in a nonstoichiometric state is changed to the RuO₂-crystalline phase in a stoichiometric state after post-deposition annealing; this phase can act as an oxygen-capture layer. Therefore, it appears that the electrical properties of the Ru/TiN/poly-Si/Si contact system are better than those of the RuO_x/TiN/poly-Si/Si contact system.     

Wireless-adaptive fair scheduling for multimedia stream

As packet cellular networks are expected to support multimedia services, the authors incorporate the multimedia QoS requirements into the design of a new scheduling algorithm. The proposed wireless-adaptive fair scheduling tries to allocate time slots for each user with fair share by considering the varying channel condition while reflecting the stream requirements and achieving high throughput.     

InP D-HBT ICs for 40-Gb/s and higher bitrate lightwave transceivers

The combination of device speed (f/sub T/, f/sub max/ > 150 GHz) and breakdown voltage (V/sub bceo/ > 8 V) makes the double heterojunction bipolar InP-based transistor (D-HBT) an attractive technology to implement the most demanding analog functions of 40-Gb/s transceivers. This is illustrated by the performance of a number of analog circuits realized in an InP D-HBT technology with an 1.2- or 1.6-/spl mu/m-wide emitter finger: a low phase noise push-push voltage-controlled oscillator with -7-dBm output power at 146 GHz, a 40-GHz bandwidth and low-jitter 40-Gb/s limiting amplifier, a lumped 40-Gb/s limiting driver amplifier with 4.5-V/sub pp/ differential output swing, a distributed 40-Gb/s driver amplifier with 6-V/sub pp/ differential output swing, and a number of distributed preamplifiers with up to 1.3-THz gain-bandwidth product.     

Magnetic effects of direct ion implantation of Mn and Fe into p-GaN

In p-GaN implanted with Mn (3×10¹⁶ cm⁻² at 250 keV), the material after annealing shows ferromagnetic properties below 250 K. Cross-sectional transmission electron microscopy (TEM) revealed the presence of platelet structures with hexagonal symmetry. These regions are most likely Ga_xMn_1−xN, which produce the ferromagnetic contribution to the magnetization. In p-GaN implanted with Fe, the material after annealing showed ferromagnetic properties at temperatures that were dependent on the Fe dose, but were below 200 K in all cases. In these samples, TEM and diffraction analysis did not reveal any secondary phase formation. The results for the Fe implantation are similar to those reported for Fe doping during epitaxial growth of GaN.     

Abnormal junction profile of silicided p+/n shallowjunctions: a leakage mechanism

The leakage mechanism in p⁺/n shallow junctions fabricated using Co silicidation and shallow trench isolation processes has been investigated using transmission electron microscopy (TEM) combined with selective chemical etching. TEM and TSUPREM-4 simulation results show that dopant profiles bend upward near the edge of the active region. The formation of the abnormal profile is attributed to transient enhanced diffusion induced by source/drain implantation. Based on the TEM and simulation results, it is suggested that the shallower junctions formed near the active edge can serve as a source for leakage current in the silicided p+ /n shallow junctions