Synthesis of ZSM‐5 Films and Monoliths with Bimodal Micro/Mesoscopic Structures

A route to synthesize ZSM‐5 crystals with a bimodal micro/mesoscopic pore system has been developed in this study; the successful incorporation of the mesopores within the ZSM‐5 structure was performed using tetrapropylammonium hydroxide (TPAOH)‐impregnated mesoporous materials containing carbon nanotubes in the pores, which were encapsulated in the ZSM‐5 crystals during a solid rearrangement process within the framework. Such mesoporous ZSM‐5 zeolites can be readily obtained as powders, thin films, or monoliths.     

High-performance MIM capacitor using ALD high-k HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectrics

For the first time, we successfully fabricated and demonstrated high performance metal-insulator-metal (MIM) capacitors with HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectric using atomic layer deposition (ALD) technique. Our data indicates that the laminate MIM capacitor can provide high capacitance density of 12.8 fF//spl mu/m/sup 2/ from 10 kHz up to 20 GHz, very low leakage current of 3.2 /spl times/ 10/sup -8/ A/cm/sup 2/ at 3.3 V, small linear voltage coefficient of capacitance of 240 ppm/V together with quadratic one of 1830 ppm/V/sup 2/, temperature coefficient of capacitance of 182 ppm//spl deg/C, and high breakdown field of /spl sim/6 MV/cm as well as promising reliability. As a result, the HfO/sub 2/-Al/sub 2/O/sub 3/ laminate is a very promising candidate for next generation MIM capacitor for radio frequency and mixed signal integrated circuit applications.     

Hydrogen annealing effect on DC and low-frequency noise characteristics in CMOS FinFETs

The hydrogen annealing process has been used to improve surface roughness of the Si-fin in CMOS FinFETs for the first time. Hydrogen annealing was performed after Si-fin etch and before gate oxidation. As a result, increased saturation current with a lowered threshold voltage and a decreased low-frequency noise level over the entire range of drain current have been attained. The low-frequency noise characteristics indicate that the oxide trap density is reduced by a factor of 3 due to annealing. These results suggest that hydrogen annealing is very effective for improving device performance and for attaining a high-quality surface of the etched Si-fin.     

Effect of anisotropy of tin on thermomechanical behavior of solder joints

Properties of body centered tetragonal tin are highly anisotropic. As a consequence large stresses can develop at the tin grain boundaries due to coefficient of thermal expansion mismatch during temperature excursions. A modeling approach to evaluate the 3D stress states that develop at grain boundaries during thermomechanical fatigue in tin-based solder is presented. Development of significant amounts of stresses in the plane of the grain boundary can cause grain-boundary sliding and surface-relief effects, while those normal to the grain boundary can cause grain-boundary decohesion and cracking.     

An intelligent web-page classifier with fair feature-subset selection

The explosion of on-line information has given rise to many manually constructed topic hierarchies (such as Yahoo!!). But with the current growth rate in the amount of information, manual classification in topic hierarchies results in an immense information bottleneck. Therefore, developing an automatic classifier is an urgent need. However, classifiers suffer from enormous dimensionality, since the dimensionality is determined by the number of distinct keywords in a document corpus. More seriously, most classifiers are either working slowly or they are constructed subjectively without any learning ability. In this paper, we address these problems with a fair feature-subset selection (FFSS) algorithm and an adaptive fuzzy learning network (AFLN) for classification. The FFSS algorithm is used to reduce the enormous dimensionality. It not only gives fair treatment to each category but also has ability to identify useful features, including both positive and negative features. On the other hand, the AFLN provides extremely fast learning ability to model the uncertain behavior for classification so as to correct the fuzzy matrix automatically. Experimental results show that both FFSS algorithm and the AFLN lead to a significant improvement in document classification, compared to alternative approaches.     

Influence of iron oxide pigments on the properties of concrete interlocking blocks

Concrete interlocking blocks (CIBs) are utilized in a variety of commercial, municipal, and industrial applications. Superior engineering properties, low maintenance, ease of placement and removal, reuse of original blocks, aesthetic appeal, and immediate availability are the primary reasons for choosing concrete block pavement over other paving surfaces. It is a common practice to pigment building materials, such as mortar, concrete pavers, concrete roof tiles, and prefabricated concrete products; CIBs are colored using iron oxide pigments. This article presents experimental results detailing the properties of CIBs dyed with pigments. The results of these experiments are as follows: Because the particles of iron oxide pigments are finer than those of brown iron oxide, interlocking blocks mixed with the former acquired higher color strength than with the latter. Additional analysis determined a definite relationship between the flexural strength and the absorption ratio of pigment-dyed blocks; the correlation coefficient (R²) of interlocking blocks at 91 days was .90. It is suggested that if iron oxide pigments are to be used to color CIBs, the pigment-to-cement ratio should be below 4%.     

Transmission performance of 10-Gb/s 1550-nm transmitters using semiconductor optical amplifiers as booster amplifiers

We have demonstrated the transmission performance of 10-Gb/s transmitters based on LiNbO/sub 3/ modulator using semiconductor optical amplifiers (SOAs) as booster amplifiers. Utilizing the negative chirp converted in SOAs and self-phase modulation induced by high optical power, we can successfully transmit 10-Gb/s optical signals over 80 km through the standard single-mode fiber with the transmitter using SOAs as booster amplifiers. SOAs can be used for booster amplifiers with a careful adjustment of the operating conditions. In order to further understand an SOA's characteristics as a booster amplifier, we model SOAs and other subsystems to verify the experimental results. Based on the good agreement between the experimental and simulation results, we can find the appropriate parameters of input signals for SOAs, such as extinction ratio, rising/falling time, and chirp parameter to maximize output dynamic range and available maximum output power (P/sub o,max/).     

Formation of a geometric pattern with a mobile wireless sensor network

Mobile wireless sensor networks (MWSNs) will enable information systems to gather detailed information about the environment on an unprecedented scale. These self‐organizing, distributed networks of sensors, processors, and actuators that are capable of movement have a broad range of potential applications, including military reconnaissance, surveillance, planetary exploration, and geophysical mapping. In many of the foreseen applications, the MWSN will need to form a geometric pattern without assistance from the user. In military reconnaissance, for example, the nodes will be dropped onto the battlefield from a plane and land at random positions. The nodes will be expected to arrange themselves into a predetermined formation in order to perform a specific task. Thus, we present algorithms for forming a line, circle, and regular polygon from a given set of random positions. The algorithms are distributed and use no communication between the nodes to minimize energy consumption. Unlike past studies of geometric problems where algorithms are either tested in simulations where each node has global knowledge of all the other nodes or implemented on a small number of robots, the robustness of our algorithms has been studied with simulations that model the sensor system in detail. The simulations demonstrate that the algorithms are robust against random errors in the sensors and actuators. © 2004 Wiley Periodicals, Inc.     

Lost retransmission detection for TCP SACK

There have been a lot of works to avoid retransmission timeout (RTO) of transmission control protocol (TCP) that takes place in an unnecessary situation. However, most current TCP implementations, even if selective acknowledgment (SACK) option is used, do not have a mechanism to detect a lost retransmission and avoid subsequent RTO. In this letter, we propose a simple modification that enables a TCP sender using SACK option to detect a lost retransmission, which is called TCP SACK+ in simple. We use a stochastic model to evaluate the performance of TCP SACK+. Numerical results evaluated by simulations show that TCP SACK+ improves the loss recovery of TCP SACK significantly in presence of random losses.     

Simultaneous amplification by Er ions and SRS in an Er-doped germano-silica fiber

A flat signal gain over in the entire C- and L-bands by erbium (Er) ions' radiative transition and stimulated Raman scattering in an Er-doped germano-silica fiber can be obtained if proper values of the concentration of Er and background loss in a fiber core are obtained during the fiber fabrication process. The optimized conditions for the flat C- and L-band gain are analyzed as functions of Er concentrations. Even for a low-gain value provided by a germano-silica core fiber with a low Er concentration and an optimum fiber length, a relatively low pump is required to obtain the flat gain band.