Inhibition effect of carbon dioxide on the oxidation of hydrogen over a platinum foil catalyst

This paper investigates the catalytic ignition of the H₂/O₂/CO₂ mixture on platinum in a stagnation flow at atmospheric pressure experimentally and numerically. We measure the ignition temperatures of the gas mixtures flowing towards resistively heated platinum with various composition ratios and various diluent gases of N₂, Ar and CO₂. Compared with N₂ or Ar, the CO₂ dilution shows higher ignition temperature by about 50 K, even at the same composition ratio. The ignition temperature increase is proportional to the dilution ratio. Through the numerical simulation, it is illustrated that higher ignition temperature is caused by the adsorption of CO₂ and following dissociation on platinum surface, which was to date considered negligible in catalytic combustion.     

An adaptive p-persistent MAC scheme for multimedia WLAN

The letter proposes an adaptive p-persistent-based (APP) medium access control (MAC) scheme for the IEEE 802.11e distributed WLAN supporting multimedia services. The APP MAC scheme adaptively gives differentiated permission probabilities to transmission stations which are in different access category and with various waiting delay. Simulation results show that the APP MAC scheme can improve the performance of multimedia WLAN, such as small voice packet dropping probability, low delay variation, and high system throughput, compared to conventional MAC algorithms     

Measurement and numerical simulation of three‐dimensional fiber orientation states in injection‐molded short‐fiber‐reinforced plastics

To determine three‐dimensional fiber orientation states in injection‐molded short‐fiber composites, a confocal laser scanning microscope (CLSM) is used. Since the CLSM optically sections the specimen, more than two images of the cross sections on and below the surface of the composite can be obtained. Three‐dimensional fiber orientation states can be determined by using geometric parameters of fiber images obtained from two parallel cross sections. For experiments, carbon‐fiber‐reinforced polystyrene is examined by the CLSM and geometric parameters of fibers on each cross‐sectional plane are measured by an image analysis. In order to describe fiber orientation states compactly, orientation tensors are determined at different positions of the prepared specimen. Three‐dimensional orientation states are obtained without any difficulty by determining the out‐of‐plane angles utilizing fiber images on two parallel planes acquired by the CLSM. Orientation states are different at different positions and show the shell–core structure along the thickness of the specimen. Fiber orientation tensors are predicted by a numerical analysis and the numerically predicted orientation states show good agreement with measured ones. However, some differences are found at the end of cavity. They may result from the fountain flow effects, which are not considered in the numerical analysis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 500–509, 2003     

Advanced disturbance observer design for mechanical positioning systems

Disturbance-observer (DOB)-based controller design is one of the most popular methods in the field of motion control. In this paper, the generalized disturbance compensation framework, named the robust internal-loop compensator (RIC) is introduced and an advanced design method of a DOB is proposed based on the RIC. The mixed sensitivity optimization problem, which is the main issue of DOB design, is also solved through the parametrization of the DOB in the RIC framework. Differently from conventional methods, the Q-filter is separated from the mixed sensitivity optimization problem and a systematic design law for the DOB is proposed. This guarantees the robustness and optimality of the DOB and enables the design for unstable plants.     

ESD protection design to overcome internal damage on interface circuits of a CMOS IC with multiple separated power pins

This paper reports a real case of electrostatic discharge (ESD) improvement on a complementary metal oxide semiconductor integrated circuit (IC) product with multiple separated power pins. After ESD stresses, the internal damage have been found to locate at the interface circuit connecting between different circuit blocks with different power supplies. Some ESD designs have been implemented to rescue this IC product to meet the required ESD specification. By adding only an extra ESD clamp N-channel metal oxide semiconductor with a channel width of 10 /spl mu/m between the interface node and the ground line, the human-body-model (HBM) ESD level of this IC product can be improved from the original 0.5 to 3 kV. By connecting the separated vertical sync signal (VSS) power lines through the ESD conduction circuit to a common VSS ESD bus realized by the seal ring, the HBM ESD level of the enhanced version IC product with 12 separated power supplies pairs can be significantly improved from original 1 kV up to > 5 kV, without the noise coupling issue.     

600 A IGBT开关电路及其散热系统设计

采用IGBT开关电路，对大功率电阻带进行直流脉宽调制控制，实现了内燃机车大功率直流发电机负载实验中的负载大小的连续调节。为了避免在实验过程中IGBT器件的温度过高，采用独特的双管IGBT结构和双向强迫风冷的散热系统。实验表明该电路运行稳定、可靠。     

Using buried capacitor in LTCC-MLC balun

A novel chip-type ceramic balun designed in the 2.4 GHz ISM band frequency is presented. A buried capacitor is included in the balun, so that the length of the coupled transmission lines can be reduced and can be designed very easily. A meander or spiral broadside coupled-line is adopted to realise the proposed LTCC multi-layer balun. The measured performances of phase and amplitude balance for this LTCC-MLC balun show a good match with computer simulation     

利用黄河泥沙加固下游大堤

黄河是一条举世闻名的多泥沙河流，善淤、善决、善徒给沿河人民带来对过深重灾难，防洪问题一直是国家的心腹之患。泥沙问题是黄河防洪问题的症结所在。在总结固大堤经验的基础，进行挖河疏浚，淤筑“相对地下河”，已作为黄河治理的一项重大决策付诸实施。     

Wideband microstrip array antenna with sidelobe cancellationchannels

An antenna array for wideband operation (up to 70%) is presented. The structure has low windloading area and consists of parallel printed circuit boards (PCB) with microstrip dipoles, feed network and metal fences placed between the PCBs. The low profile, low weight antenna array forms the main beam and three difference patterns for sidelobe cancellation. Experimental results are compared with calculations for both microstrip dipole and array     

High-performance automatic target recognition through data-specificVLSI

Under the Mojave configurable computing project, we have developed a system for achieving high performance on an automatic target recognition (ATR) application through the use of configurable computing technology. The ATR system studied here involves real-time image acquisition from a synthetic aperture radar (SAR). SAR images exhibit statistical properties which can be used to improve system performance. In this paper, the Mojave configurable computing system uses field programmable gate arrays (FPGA's) to implement highly specialized circuits while retaining the flexibility of programmable components. A controller sequences through a set of specialized circuits in response to real-time events. Computer-aided design (CAD) tools have been developed to support the automatic generation of these specialized circuits. The resulting configurable computing system achieves a significant performance advantage over the existing solution, which is based on application specific integrated circuit (ASIC) technology