攀钢转炉炼钢用碳化硅提温的试验研究

低品位碳化硅是转炉炼钢的有效提高温剂。工业性试验结果表明，碳化硅加入８．０ｋｇ／ｔ钢水提温４０．３－７０．３℃（平均４８．４℃）；渣中ＴＦｅ降低１．３％；加提温剂有利于转炉内造渣脱硫和碱少炉渣对耐火砖的侵蚀。文中还给出了攀钢转炉半钢冶炼铸用钢不水时加与不加碳化硅的ｔλ，［Ｃ］λ区域。     

关于CEA混凝土膨胀剂的若干技术问题--与游宝坤同志讨论

作者阐述了CEA膨胀剂混凝土的膨胀量较大，干缩小，抗裂性能良好的特性，CEA与粉煤灰掺用提高强度，改善界面过渡层的性质，提高耐久性；CEA混凝土无Ca（OH）2溶出问题。文中列出GBJ119应用技术规范，说明CEA可用于防水工程。     

Fuzzy estimation of feed-cutting force from current measurement-a case study on intelligent tool wear condition monitoring

It is very important to use a reliable and inexpensive sensor to obtain useful information about manufacturing processing, such as cutting force for monitoring automated machining. In this paper, the feed-cutting force is estimated using inexpensive current sensors installed on the ac servomotor of a computerized numerical control (CNC) turning center, with the results applied to the intelligent tool wear monitoring system. The mathematical model is used to disclose the implicit dependency of feed-cutting force on feed-motor current and feed speed. Afterwards, a neuro-fuzzy network is used to identify the cutting force with current measurement only. This hybrid math-fuzzy approach will reduce the modeling uncertainty and measurement cost. Finally, the estimated cutting force is applied in the tool-wear monitoring process. Successful experiments demonstrate robustness and effectiveness of the suggested method in the wide range of tool-wear monitoring applications.     

A polymerizable photoredox initiation system for vinyl photopolymerization

A polymerizable photoredox system consisting of 4-methacryl oxbenzophenone (MABP) and N,N-dimethlaminoethyl methacrylate (DMAEMA) used for the photopolymerization of acrylonitrile (AN) was studied. It was found that the polymerization rate is proportional to the 0.93th power for the AN concentration, the 0.28th power for the MABP concentration, and the 0.25th power for the DMAEMA concentration. The overall activation energy of the polymerization obtained is 30.43 kJ/mol. The recorded ESR spectrum indicates that the excited-state MABP abstraets hydrogen mainly from the methyl group of the dimethylamino moiety. The comparison of the initiation ability of polymeric MABP or polymeric DMAEMA with their monomeric forms has also been done and the results indicate that in good solvents P (MABP) has a much higher initiation ability than that of monomeric MABP, but monomeric DMAEMA and P (DMAEMA) display almost the same initiation ability. In poor solvent, the initiation ability of P (MABP) is not so obviously higher than that in good solvents. The result of UV analysis of P (AN) initiated by the MABP–DMAEMA system indicates that both MABP and DMAEMA not only initiate the photopolymerization of AN, but also enter into P (AN) polymer chains. © 1994 John Wiley & Sons, Inc.     

CAPP系统中工艺卡片生成过程的研究

以AutoCAD2 0 0 0为开发平台、VC + + 6 0为开发环境、ObjectARX2 0 0 0为开发工具、SQLServer为后台数据库 ,通过编写writeText、fillGykztb、fillGykjtb等自定义函数 ,生成工艺卡片 ,并实现工序内容在工艺卡片中的分页显示等功能。     

Monolithic SiGe Up‐/Down‐Conversion Mixers with Active Baluns

The purpose of this paper is to describe the implementation of monolithically matching circuits, interface circuits, and RF core circuits to the same substrate. We designed and fabricated on‐chip 1 to 6 GHz up‐conversion and 1 to 8 GHz down‐conversion mixers using a 0.8 µm SiGe hetero‐junction bipolar transistor (HBT) process technology. To fabricate a SiGe HBT, we used a reduced pressure chemical vapor deposition (RPCVD) system to grow a base epitaxial layer, and we adopted local oxidation of silicon (LOCOS) isolation to separate the device terminals. An up‐conversion mixer was implemented on‐chip using an intermediate frequency (IF) matching circuit, local oscillator (LO)/radio frequency (RF) wideband matching circuits, LO/IF input balun circuits, and an RF output balun circuit. The measured results of the fabricated up‐conversion mixer show a positive power conversion gain from 1 to 6 GHz and a bandwidth of about 4.5 GHz. Also, the down‐conversion mixer was implemented on‐chip using LO/RF wideband matching circuits, LO/RF input balun circuits, and an IF output balun circuit. The measured results of the fabricated down‐conversion mixer show a positive power conversion gain from 1 to 8 GHz and a bandwidth of about 4.5 GHz.     

Dynamic Survivability in WDM Mesh Networks Under Dynamic Traffic

Network survivability is a crucial requirement in WDM mesh networks. In this paper, we systematically consider the problem of dynamic survivability with dynamic single link failure in WDM networks under dynamic traffic demands. Specifically, we investigate various protection schemes, such as dedicated path protection (DPP), shared path protection (SPP), dedicated link protection (DLP), shared link protection (SLP), and two restoration schemes, path restoration (PR) and link restoration (LR). Moreover, two new shared protection methods are proposed, i.e., SRLG-based shared link protection (SRLG-SLP) and SRLG-based shared path protection (SRLG-SPP). The SRLG (shared risk link group) constraint defines the availability of protection resources to a working path, which requires that any two working paths sharing the same risk of failure (or in the same SRLG) cannot share the same protection resources. Furthermore, in our study, we consider a more practical dynamic single-link failure model, in which the link-failure-interarrival time and link-failure-holding time are considered as two independent parameters. Based on this link-failure model, extensive simulations are done to analyze and compare the dynamic survivable performance of various protection and restoration schemes. Resource utilization, protection efficiency, restoration efficiency, and service disruption ratio are employed as survivable performance metrics versus traffic load, link-failure frequency, and link-failure reparation time to evaluate the survivable performance. Many meaningful results are given. In addition, we show that the developed SRLG-SLP and SRLG-SPP protection schemes perform very well in terms of protection efficiency and service disruption ratio, while sacrificing some performance in terms of resource utilization.