Flexural behaviour and strength of cold-formed steel L-headers

Cold-formed steel headers are structural components used over wall openings in cold-formed steel residential and light commercial construction. Recently, there has been an increased interest in cold-formed L-headers among homebuilders primarily due to their ease of installation and low material cost. The findings from an extensive laboratory testing program, of full-scale single and double cold-formed steel L-headers are presented in this paper. The objective of the research was to investigate the flexural behaviour and strength of L-headers under both gravity and uplift loads. Based on the results improved ultimate strength design expressions and new deflection expressions for a wide range of L-header assemblies have been proposed.     

Extracting local mechanical properties of steel bars by means of instrumented flat indentation

The evaluation of local mechanical properties of metal parts can be used for the prediction of forming and cutting forces during the following working stages. In order to show the feasibility of using indentation tests for work-piece characterization, C40 steel disks were cut from an extruded bar and machined by facing operation under different conditions. Indentation tests were carried out with 1 mm and 2 mm diameter indenters made of tungsten carbide; yield strength and indentation pressure values were extracted along the diameter of each disk. For the first time, indentation results were used to extract local mechanical properties of steel bars as a function of their process conditions: it was observed that small pins gave information on the effect of the machining process whereas large pins were more suitable to evaluate work-piece bulk properties.     

A tall tower study of Missouri winds

This paper summarizes the results of a study of wind speeds observed at heights up to 150 m above ground level around Missouri. This is an amalgamation of four projects that allowed a total of eleven tall communication towers to be instrumented with wind observation equipment across the State of Missouri. This provided an assessment of the wind resource and the characteristics of the seasonal and diurnal cycles of wind in different areas of Missouri at the heights of utility scale wind turbines. Comparisons were also made to wind speeds predicted at these levels from a previously published wind map.The main finding was that the observed winds at each tower were smaller than those presented in the wind map. The discrepancy is most likely to be due to underestimation of the surface roughness and turbulence leading to an overestimation of near-surface wind shear. However, the wind shear, as expressed by the shear parameter was consistently greater than the ‘standard’ value of 1.4. The reconciliation of these two apparently contradictory findings is that the shear varies with the height at which it is measured. In wind resource assessment, wind shear is usually observed below 50 m and is tacitly assumed to be constant with height when used to extrapolate winds to higher levels. The author advocates the use of the friction velocity as a measure of shear in wind power applications in preference to the shear parameter that is usually used. This is because the shear parameter has a velocity bias that can also manifest as a bias with height or season. As wind power resource assessment is starting to use taller towers than the standard 50 m, intercomparison of site resources and extrapolation to turbine heights can be compromised if the shear parameter is used.     

Reducing greenhouse gas emissions through operations and supply chain management

The experiences of the largest corporation in the world and those of a start-up company show how companies can profitably reduce greenhouse gas emissions in their supply chains. The operations management literature suggests additional opportunities to profitably reduce emissions in existing supply chains, and provides guidance for expanding the capacity of new “zero emission” supply chains. The potential for companies to profitably reduce emissions is substantial but (without effective climate policy) likely insufficient to avert dangerous climate change.     

伦敦帕丁顿中心Two Kingdom Street项目

<正>KPF设计师事务所已完成了Two Kingdom Street项目设计。该项目投资8800万英镑,由Development Securities公司开发,为Aviva Investors公司和Quinlan Private公司所有。该项目提供了2.2万m2的最佳办公空间,是帕丁顿中心项目第二阶段的最新增加项目,位于帕丁顿火车站附近的大型综合开发区内。     

Effect of transglutaminase on the heat stability of milk: a possible mechanism

Treatment of milk with transglutaminase (TGase) affects its heat stability, but the manner in which it does so depends on whether or not the milk had been preheated before incubation and on the temperature of preheating. In raw milk, it appears that cross-link formation between the individual caseins is responsible for preventing the dissociation of kappa-casein from the micelles at pH values in the region of minimum stability. In milks preheated before incubation with TGase, denaturation of whey protein may have allowed the formation of cross-links by TGase between denatured whey proteins and the individual caseins which, in combination with cross-linking of the caseins, contributed to greatly improved heat stability at pH > 6.5. It appears from the results of this study that TGase has potential commercial applications as a food-grade additive capable of improving the heat stability of milk.     

Fourier-Bessel field calculation and tuning of a CW annular array

A 1-D Fourier-Bessel series method for computing and tuning the linear lossless field of flat continuous wave (CW) annular arrays is given and discussed with both numerical simulation and experimental verification. The technique provides a new method for modelling and manipulating the propagated field by linking the quantized surface pressure profile to a set of limited diffraction Bessel beams propagating into the medium. In the limit, these become a known set of nondiffracting Bessel beams satisfying the lossless linear wave equation, which allow us to derive a linear matrix formulation for the field in terms of the ring pressures on the transducer surface. Tuning (beamforming) of the field then follows by formulating a least squares design with respect to the transducer ring pressures. Results are presented in the context of a 10-ring annular array operating at 2.5 MHz in water.     

High density net shape components by direct laser re-melting of single-phase powders

Direct Metal Laser Re-Melting is a variant of the Selective Laser Sintering process, a Rapid Prototyping (RP) technology. This tool-less manufacturing technology has the potential of producing complex, high quality components from single-phase metal powders in short time scales. This is made possible by the production of consecutive two-dimensional layers. Unfortunately, finished components manufactured by this technique have their integrity and material properties dictated by the porosity within the laser re-melted structure. In order to maintain structural integrity comparable to conventionally produced components, metal components produced by the rapid prototyping method should exhibit a porosity of the order of maximum of 2% with corresponding bulk material properties. To achieve these objectives, process and laser parameters require optimisation for maximum densities to be attained. This paper reports on the development of a scanning strategy that produces stainless steel (316L) laser re-melted components which exhibit porosities of <1%, while maintaining the concept of rapid prototyping.