A Ultra-Wideband Amplitude Modulation (AM) Detector Using Schottky Barrier Diodes Fabricated in Foundry CMOS Technology

Utility of Schottky diodes fabricated in foundry digital 130-nm CMOS technology is demonstrated by implementing an ultra-wideband (UWB) amplitude modulation detector consisting of a low-noise amplifier (LNA), a Schottky diode rectifier, and a low-pass filter. The input and output matching of the detector is better than -10 dB from 0-10.3 GHz and 0-1.7 GHz, respectively, and almost covers the entire UWB frequency band (3.1-10.6 GHz). The measured peak conversion gain is -2.2dB. The sensitivity over the band for amplitude modulation with the minimum E _b/N_o of 6 dB is between -53 and -56 dBm. The power consumption is only 8.5 mW     

Epitaxial nucleation model for chiral-selective growth of single-walled carbon nanotubes on bimetallic catalyst surfaces

An epitaxial nucleation model for single-walled carbon nanotube (SWCNT) growth on bimetallic catalysts surfaces is reported in support of experimental observations of chiral enrichment. We model the bimetallic catalyst surfaces as a 2D (1 1 1) surface consisting of Ni or a combination of Ni and Fe atoms, with varying average bond length between nearest neighbor atoms which corresponds to the crystal structure of the alloys. The energies associated with nanotube cap formation on these various surfaces are calculated using density functional theory (DFT). We find that certain cap chiralities, such as (8, 4), are more stably bound to a surface that resembles a Ni_0.27Fe_0.73 bimetallic catalyst, whereas other chiralities, such as (9, 4), are more stable on a pure Ni surface. These results help explain the predominance of certain chiralities on specific bimetallic catalysts and provide a potential route to controlling the chirality of as-grown SWCNTs.     

Applicability of time-of-flight-based ground and multispectral aerial imaging for grapevine canopy vigour monitoring under direct root-zone deficit irrigation

ABSTRACT

This study investigates the applicability of ground-based 3D time-of-flight (ToF) imaging and small unmanned aerial system (UAS) integrated multispectral imaging as a rapid grapevine canopy vigour mapping tool for decision support during crop production management. Direct root-zone deficit irrigation was applied to grapevines with continuous and pulse irrigation techniques at 15%, 30%, and 60% rates as that of standard irrigation rate (100%) established by the grower in a commercial production. The control block was irrigated continuously at 100% standard irrigation rate. Field plots were imaged using ground platform integrated with 3D ToF imaging sensor and small UAS-integrated multispectral camera at 128 and 65 days before the harvest to estimate the canopy vigour variability associated with irrigation treatments. Customized as well as standard methods (convex hull and voxel grid) were utilized to extract canopy attributes (e.g. volume) from the 3D ToF imaging sensor data. The multispectral images were processed to extract normalized and green normalized difference vegetation index images. Resulting data were used to estimate canopy area ratio i.e. the ratio between the grapevine canopy area with respect to the total area in selected region of interest. A significant correlation (r = 0.34) between canopy volume estimated by customized algorithm and aerial canopy area ratio was observed. Custom canopy volume estimates were also highly correlated (r = 0.79) with voxel grid derived canopy volume data. Overall, 60% continuous direct root zone deficit irrigation appeared to produce canopy volume/vigour comparable with those under control treatment. Results also suggest that grower can utilize either or both (ground and aerial) grapevine canopy mapping techniques for effective management.     

Practices,projects and portfolios: Current research trends and new directions

Project portfolio management (PPM) bridges strategy and project management. Traditional research in PPM has primarily investigated the rational, top-down and structural aspects of strategizing. By doing so, it has failed to focus on the underlying practices that are triggered by the strategy and how these practices frame strategy implementation. Practice-based research provides a methodological lens to explore the reality of strategic enactment through the project portfolio. Practice-based perspectives are under-represented in PPM research; therefore the aim of this paper is to provide an agenda for further practice-based research in PPM. Central to this agenda is a concern with various aspects of practice, including its discursivity, representation, dynamic capabilities, leadership and materiality.     

Transmission electron microscopy studies of thermomechanically control processed multiphase medium-carbon microalloyed steel: Forged, rolled, and low-cycle fatigued microstructures

A ferrite-bainite-martensite (F-B-M) microstructure was produced in a medium-carbon microalloyed (MA) steel through two routes, namely, low-temperature finish forging and rolling, followed by a two-step cooling (TSC) and annealing. Transmission electron microscopy (TEM) was employed to study the microstructural evolution in control forged and rolled material after TSC followed by annealing (TSCA). A TEM investigation was also carried out on samples low-cycle fatigue (LCF) tested at low and high total strain amplitudes of 0.4 and 0.7 pct in case of the forged steel (F-B-M(F)TSCA) and 0.55 and 0.8 pct for the rolled steel (F-B-M(R)TSCA), respectively. Microstructural changes accompanying the LCF testing were identified. The two-step cooled microstructure processed through forging (F-B-M(F)TSC) as well as rolling (F-B-M(R)TSC) revealed a complex multiphase microstructure, along with films and blocks of retained austenite. In both microstructural conditions, vanadium carbide precipitates were too fine to be identified after the TSC treatment. Annealing after TSC produced a stress-free microstructure. The F-B-M(F)TSCA microstructure predominantly consisted of granular/lower bainite, lath martensite, and polygonal ferrite with interlath films as well as blocks of retained austenite, while the F-B-M(R)TSCA microstructure predominantly consisted of lath martensite, granular/lower bainite, and polygonal ferrite with interlath strips/films of retained austenite. Lath martensite content was higher in the F-B-M(R)TSCA condition than in the F-B-M(R)TSCA condition. In both conditions, vanadium carbide precipitates could be seen after annealing. Fatigue-tested F-B-M(F)TSCA microstructure up to a total strain amplitude of 0.4 pct and F-B-M(F)TSCA microstructure up to a total strain amplitude of 0.55 pct were stable. Lath martensite did not undergo deformation and in both microstructural conditions dislocation cell structures were not observed in the ferrite or bainite regions. The interlath retained austenite strips/films played a significant role in preventing the softening during fatigue loading. First, it was stable up to a total strain amplitude of 0.4 and 0.55 pct in the respective microstructures. Second, it underwent heavy deformation during fatigue loading at high total strain amplitudes, thereby accommodating the strain. Fatigue-tested F-B-M(F)TSCA microstructure at a total strain amplitude of 0.7 pct and F-B-M(R)TSCA microstructure at a total strain amplitude of 0.8 pct revealed deformed bainite/martensite laths, dislocation cells, and slip bands in the ferrite regions, which are characteristic features of cyclic softening. The retained austenite transformed to martensite through a strain-induced transformation mechanism and, at that stage, the microstructure contained in addition dislocation-rich bainite and ferrite.     

Polarization discrimination of coherently propagating light in turbid media

We describe the use of degree of polarization to discriminate unscattered and weakly scattered light from multiply scattered light in an optically turbid material. We use spatially resolved measurements of the degree of polarization to compare how well linearly and circularly polarized light survives in a sample. Experiments were performed on common tissue phantoms consisting of polystyrene and Intralipid microsphere suspensions and on adipose and arterial tissue. The results indicate that polarization is maintained even after unpolarized irradiance through each sample has been extinguished by several orders of magnitude. The results also show that polarized light propagation in common tissue phantoms is distinctly different from polarized light propagation in the two tissues investigated. Further, these experiments illustrate when polarization is an effective discrimination criterion and when it is not. The potential of a polarization-based discrimination scheme to image through the biological and nonbiological samples investigated here is also discussed.     

Native and oxidized low density lipoproteins modulate mesangial cell apoptosis

Hyperlipidemia has been demonstrated to contribute to hypercellularity of the mesangium in experimental animal models of glomerulosclerosis. We studied whether it also has the potential to convert a hypercellular mesangium into a hypocellular one by inducing mesangial cell (MC) apoptosis. Low density lipoprotein (LDL) enhanced (P < 0.001) mouse mesangial cell (MMC) proliferation at lower concentrations (control, 10.3 +/- 0.3 vs. LDL 100 micrograms/ml, 24.2 +/- 0.3 x 10(4) cells/ml) but augmented (P < 0.001) apoptosis at higher concentrations (control, 5.6 +/- 0.5% vs. LDL, 500 micrograms/ml 26.2 +/- 3.4% apoptotic cells/field). Oxidized (OX) LDL enhanced MMC apoptosis in concentrations of 50 to 200 micrograms/dl. There was a direct relationship between MMC apoptosis and oxidation of LDL as judged by measuring thiobarbituric acid reactive species (TBARS). Since superoxide dismutase (SOD) attenuated (P < 0.001) LDL-induced MMC apoptosis, it seems to be mediated through the generation of free radicals by mesangial cells (control, 4.3 +/- 1.5%; LDL, 200 micrograms/ml, 19.4 +/- 0.5%; LDL + SOD, 8.1 +/- 1.3% apoptotic cells/field). LDL also induced a similar effect on human mesangial cells. These studies were further confirmed by DNA fragment assays and ELISA for programmed cell death. LDL treated cells also showed enhanced mRNA expression for RSG-2, a marker for active cell death. These in vitro results provide a basis for the speculation that LDL has the potential to cause an initial hypercellular and subsequent hypocellular mesangium in the course of the development of glomerulosclerosis.     

Electronic error compensation of a current transformer

A scheme is presented employing two precision resistors and an electronic amplifier for reducing the ratio and phase-angle errors in a current transformer. The amplifier supplies only the error current. The proposed arrangement facilitates the adaptability of inexpensive low ampere-turn c.t.s for calibration work in the laboratory.     

Collocation-based stochastic finite element analysis for random field problems

A stochastic response surface method (SRSM) which has been previously proposed for problems dealing only with random variables is extended in this paper for problems in which physical properties exhibit spatial random variation and may be modeled as random fields. The formalism of the extended SRSM is similar to the spectral stochastic finite element method (SSFEM) in the sense that both of them utilize Karhunen–Loeve (K–L) expansion to represent the input, and polynomial chaos expansion to represent the output. However, the coefficients in the polynomial chaos expansion are calculated using a probabilistic collocation approach in SRSM. This strategy helps us to decouple the finite element and stochastic computations, and the finite element code can be treated as a black box, as in the case of a commercial code. The collocation-based SRSM approach is compared in this paper with an existing analytical SSFEM approach, which uses a Galerkin-based weighted residual formulation, and with a black-box SSFEM approach, which uses Latin Hypercube sampling for the design of experiments. Numerical examples are used to illustrate the features of the extended SRSM and to compare its efficiency and accuracy with the existing analytical and black-box versions of SSFEM.