Mean residence time of gas in mechanically agitated gas–liquid contactors

In the present study of gas–liquid contactors, mean residence/contact time was calculated from knowledge of superficial velocity and the gas phase hold-up, for various gas rates and impeller geometry and speeds, and compared with values obtained from RTD measurements. A new correlation, involving Flow Number, Froude Number, system geometry and the physical properties, is proposed. This uses the authors data and those available in literature.     

Experimental estimate of self-irradiation of building bricks due to incorporated radionuclides

A method is described for experimentally determining the dose rate created in building bricks by incorporated natural radionuclides. It was established using the thermoluminescence dosimetry method that the measured dose rate depends on the detector thickness, the mass of the ceramic product investigated, and the irradiation geometry. The contributions to the measured dose of weakly penetrating α and β radiation and hard ψ radiation are separated, the ratio between them depending on the experimental conditions. Translated from Izmeritel'naya Tekhnika, No. 7, pp. 62–66, July, 1996.     

The morphological stability of lateral growth in solid-solid phase transformation during thin-film interdiffusion in Al/Cu bimetal films

This article describes the phenomenon of morphological instability in solid-solid phase transformations during thin-film interdiffusion, specifically related to the initial stages of precipitation when phase growth occurs along the interface between thin films. The experimental observations that revealed this effect will be presented, and a working hypothesis will be discussed. Experimental observations suggest that the ledge mechanism of growth is present in this system but does not inhibit the formation of interfacial instabilities. It is proposed that morphological stability for solid-phase growth occurring during thin-film interdiffusion can be treated by the inclusion of a solute-source term into the two-dimensional perturbation approach generally used to study unstable growth morphologies. Experimental observations that provide qualitative and semiquantitative support for the solute-source model are also presented.     

Perinatal problems and the prevention of premature labor]

The article describes the experience of implementing patient-focused care from a physician's perspective. Pitfalls that guarantee failure are presented, many of which are avoidable with early participation by all parties involved: administrators, nursing staff, physicians, and patients. Contamination of the process with downsizing needs, lack of support for staff in dealing with necessary change, loss of administrative commitment, and withholding of appropriated funds are among the key errors to be avoided.     

Magnet Safety Assessment for ITER

The ITER magnet system consists of structurally linked sets of toroidal (TF) and poloidal (PF) field coils, central solenoid (CS), and various support structures. The coils are superconducting, force flow Helium cooled with a Kapton-Glass-Epoxy multilayer insulation system. The stored magnetic energy is about 100GJ in the TF system and 20GJ in the PF-CS. Coils and structure are maintained at 4 K by enclosing them in a vacuum cryostat. The cryostat, comprising an outer envelope to the magnets, forms most of the second radioactivity confinement barrier. The inner primary barrier is formed by the vacuum vessel, its ports and their extensions. To keep the machine size within acceptable bounds, it is essential that the magnets are in close proximity to both of the nuclear confinement barriers. The objective of the magnet design is that, although local damage to one of the barriers may occur in very exceptional circumstances, large scale magnet structural or thermal failure leading to simultaneous breaching of both barriers is not credible. Magnet accidents fall into three categories: thermal (which includes arcing arising from insulation failure and local overheating due to discharge failure in the event of a superconductor quench), structural (which includes component mechanical failure arising from material inadequacies, design errors and exceptional force patterns arising from coil shorts or control failures), and fluid (Helium release due to cooling line failure). After a preliminary survey to select initial faults conceivable within the present design, these faults are systematically analyzed to provide an assessment of the damage potential. The results of this damage assessment together with an assessment of the reliability of the monitoring and protective systems, shows that the magnets can operate with the required safety condition.     

Design and performance evaluation of a banyan network basedinterconnection structure for ATM switches

This paper presents a new self-routing packet network called the plane interconnected parallel network (PIPN). In the proposed design, the traffic arriving at the network is shaped and routed through two banyan network based interconnected planes. The interconnections between the planes distribute the incoming load more homogeneously over the network. The throughput of the network under uniform and heterogeneous traffic requirements is studied analytically and by simulation. The results are compared with the results of the baseline network and another banyan network based parallel interconnection network. It is shown that, for the proposed design, a higher degree of heterogeneity results in better performance     

A fully soft-switched extended-period quasi-resonantpower-factor-correction circuit

This paper presents the design criteria, procedure, and implementation of a soft-switched power-factor-correction (PFC) circuit based on the extended-period quasi-resonant (EPQR) principles. All power electronic devices including switches and diodes in the circuit are fully soft switched. The design method is demonstrated in a prototype circuit. The operating principles are confirmed with computer simulation and experimental results. A comparison of the EP-QR operation and zero-voltage-transition (ZVT) pulse-width modulation (PWM) method     

Densification involved in the UV-based photosensitivity of silicaglasses and optical fibers

A comprehensive survey of photosensitivity in silica glasses and optical fiber is reviewed. Recent work on understanding the mechanisms contributing to germanium or aluminum doped fiber photosensitivity is discussed within the framework of photoelastic densification models     

A new lateral MOS-gated thyristor with controlling base-current

A new lateral MOS-gated thyristor, called the Base-Current-Controlled Thyristor, is described. This device is designed so that most holes at the on-stage reach the P base through the floating P⁺ region adjacent to the P base and the on-state MOSFET. At the turn-off stage, the interruption of the hole current to the P base due to switching off the above MOSFET occurs simultaneously with the conventional turn-off operation. The concept of this device is verified experimentally by using the fabricated lateral device with the external MOSFET. This device exhibits a better trade-off relation between the on-state voltage and the turn-off time compared uith the conventional MOS-gated thyristor