Three ways to implement interfacial techniques: application tomeasurements of chromatic dispersion, birefringence, and nonlinearsusceptibilities

Depending on the spectal width of the source illuminating an interferometer, measurement procedures can utilize either the whole interferogram, or only the fringe envelope, or only the fringe quick oscillations. With an ultraband spectrum source, a simplified adaptation of the methods of Fourier transform spectroscopy yields the variations of the test-fiber propagation constant over the whole wavelength-interval of the source. Chromatic dispersion can then be computed from a single interferogram. With narrower spectrum sources, only the fringe envelopes are utilized and yield measurements of mode delay, with application to chromatic and polarization mode dispersion. In this case, however, interferograms at several wavelengths are necessary. With even narrower spectrum sources, the fringe quick oscillations provide measurements of phase shifts, related to changes in the mode propagation constant, when outside perturbations are applied to the test fiber. A direct method for measuring the third-order nonlinear susceptibilities is discussed. In this case the outside perturbation is an intense pump laser field     

A comparison between the axial flux and the radial flux structures for PM synchronous motors

The aim of this paper is the comparison of the axial flux (AF) structures versus the conventional radial flux (RF) structures for permanent-magnet synchronous motors. The comparison procedure is based on simple thermal considerations. Two motor typologies are chosen and compared in terms of delivered electromagnetic torque. The comparison is developed for different motor dimensions and the pole number influence is put into evidence. The paper reports the complete comparison procedure and the related results analysis. The obtained results show that, when the axial length is very short and the pole number is high, the AF motors can be an attractive alternative to the conventional RF solutions.     

Half-bridge inverter using 4H-SiC gate turn-off thyristors

This paper reports on the first demonstration of a half-bridge power inverter constructed from silicon carbide gate turn-off thyristors (GTOs) operated in the conventional GTO mode. This circuit was characterized with input bus voltages of up to 600 VDC and 2 A (peak current density of 540 A/cm²) with resistive loads using a pulse-width modulated switching frequency of 2 kHz. We discuss the implications of the thyristor's electrical characteristics and the circuit topology on the overall operation of the half-bridge circuit. This work has determined the conservative critical rate of rise value of the off-state voltage to be 200 V/μs in these devices     

Incremental transmission loss allocation under pool dispatch

Incremental transmission loss analysis has been used for decades, but recent interest in its application to loss allocation calls for new in-depth results. This paper demonstrates that, for incremental methods to be applied correctly in loss allocation, it is first necessary to specify the load distribution and loss supply strategies. Incremental loss allocation among bus power injections is shown to be arbitrary and, therefore, open to challenge as discriminatory. Loss allocation is possible among incremental loads and/or generators, but the proportion of the total losses assigned to either one is arbitrary. Unique, nonarbitrary incremental loss allocations are however possible among the "equivalent" incremental bilateral exchanges between generators and loads. From these basic components it is possible then to calculate the allocation among generators or loads in any specified proportion. The main results, although developed initially for small increments, are extended to large variations. Finally, a general incremental loss allocation algorithm is developed and tested     

约旦坦努尔RCC坝达到高标准

坦努尔坝是约旦的第一座RCC坝。该坝RCC铺筑采用斜层施工，提高工数50％。大坝上游面，下游台阶，阶梯式溢洪道，止水面以及RCC与坝肩石灰岩的交界面均采用GE－RCC。质量控制测试数据表明，该坝达到了国际大坝委员会会刊不久将发表的RCC坝质量标准的优良等级。     

Crisis phenomena upon evaporation in grid capillary and porous coatings and arterial structures of heat pipes

The article presents the results of experimental investigations of critical (limit) heat fluxes upon evaporation on porous coatings, and it substantiates the physical model of the process.Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 49, No. 4, pp. 607–614, October, 1985.     

Structure and composition of guanidine acrylate, guanidine methacrylate, their homopolymers, and copolymers with diallyldimethylammonium chloride

Structures and compositions of the monomers guanidine acrylate and guanidine methacrylate, their homopolymers, and copolymers with diallyldimethylammonium chloride enriched in acrylate comonomer units were determined. It was shown that ampholytic copolymers, owing to their ionic nature, contained comonomeric guanidine acrylate or methacrylate units and diallyldimethylammonium chloride units, as well as the acrylate comonomer with the diallyl counterion and polymeric acrylate and diallyl ion pairs. It follows from IR and ¹H NMR data that guanidine methacrylate has the same structure (with two hydrogen bonds) in the solid state and in solutions. Guanidine acrylate structures in the solid state and in dimethylsulfoxide are identical and analogous to guanidine methacrylate structure in this solvent. In water, the guanidine acrylate structure has another type of hydrogen bonding (with one hydrogen bond, where the proton is shifted toward the guanidine group). These features of hydrogen bonding of guanidine acrylate and guanidine methacrylate are also retained in their homopolymers and copolymers with diallyldimethylammonium chloride. It was shown that the thermal stability of the copolymers was higher than that of their homopolymers, confirming the formation of intramolecular ion pairs of oppositely charged units of ampholytic copolymers. Moreover, the thermal stability of guanidine methacrylate-diallyldimethylammonium chloride copolymers is higher than that of guanidine acrylate-diallyldimethylammonium chloride copolymers.