Self-oscillating dimmable electronic ballast

This paper presents a simple alternative for an electronic ballast operating in self-sustained oscillating mode with dimming capability for fluorescent lamps. A simple modification in one of the gate drivers side circuit allows the lamp to dim without compromising the simplicity, reliability, and low cost which characterize the self-oscillating electronic ballast (SOEB). A qualitative analysis is presented to explain the behavior of the proposed self-oscillating electronic ballast with dimming feature. In addition, the stability and the key equations for the design are derived using the extended Nyquist criterion and describing function method. Experimental results from two 40-W electronic ballasts are presented to demonstrate the performance and to validate the analysis carried out.     

Transient response of ARROW VCSELs under external optical feedback

The effect of external optical feedback on the transient response of antiresonant reflecting optical waveguide (ARROW) vertical-cavity surface-emitting lasers (VCSELs) is studied. It can be shown that the proper design of ARROW can suppress the excitation of high-order transverse leaky mode as well as increase the critical feedback strength so that stable high-power single-mode operation of VCSELs can be obtained even under the influence of strong external optical feedback.     

Alternating-direction implicit (ADI) formulation of the finite-difference time-domain (FDTD) method: algorithm and material dispersion implementation

The alternating-direction implicit finite-difference time-domain (ADI-FDTD) technique is an unconditionally stable time-domain numerical scheme, allowing the /spl Delta/t time step to be increased beyond the Courant-Friedrichs-Lewy limit. Execution time of a simulation is inversely proportional to /spl Delta/t, and as such, increasing /spl Delta/t results in a decrease of execution time. The ADI-FDTD technique greatly increases the utility of the FDTD technique for electromagnetic compatibility problems. Once the basics of the ADI-FDTD technique are presented and the differences of the relative accuracy of ADI-FDTD and standard FDTD are discussed, the problems that benefit greatly from ADI-FDTD are described. A discussion is given on the true time savings of applying the ADI-FDTD technique. The feasibility of using higher order spatial and temporal techniques with ADI-FDTD is presented. The incorporation of frequency dependent material properties (material dispersion) into ADI-FDTD is also presented. The material dispersion scheme is implemented into a one-dimensional and three-dimensional problem space. The scheme is shown to be both accurate and unconditionally stable.     

Scale Up from Small Oven-Drying Tests of Mineral Concentrate to Pilot-Scale Drying with a Heated Pad

While Fickian diffusion models are commonly used in other applications, there are few reports of them being applied to the batch drying of a mineral concentrate. Diffusion coefficients estimated from small-scale oven-drying tests were used to predict the drying behavior of a concentrate sample 1 m × 1 m in area and 50 cm deep, with a heated bottom pad. These pilot-scale tests included both daily turning of the sample and turning every three days. The excellent quantitative agreement between the predicted and observed pilot-scale behavior gives a high level of confidence in the model predictions and suggests that a Fickian diffusion model is adequate to predict the behavior of mineral concentrates at the low moisture contents used here.     

Smooth profile generation for a tile printing machine

In this paper a digital filter is proposed for the generation of smooth set points for motion control systems. The proposed nonlinear filter produces profiles with bounded velocity and acceleration starting from rough reference signals (steps and ramps). An actual implementation of the filter for a tile printing machine is presented and experimental results are reported.     

Estimation and Optimization of the Principal H-Maser Parameters

The scale along the coordinate axes in the equations of motion hitherto used for an H-maser (in relative units) is shown to depend on Q as the quality factor for an H-maser. This hinders both analysis of the operation of the H-maser and optimization of its parameters. The modified equations of motion proposed here do not have that shortcoming. We determine the atomic flux into the bulb that gives the H-maser the best metrological characteristics.     

Changes in the gaseous H2S barrier properties of damaged silicate coated nylon 6 films

The damage imposed on SiO _x deposited nylon 6 films as a result of abrasion with a cotton cloth and Gelboflex testing was examined by evaluating the rate at which copper plates, which were enveloped by the damaged films, were corroded by H₂S. Abrasion with a cotton cloth caused some micro-cracking of the SiO _x layer and the permeation rate of H₂S approached that of the uncoated nylon 6 film. Damage to the SiO _x layer by twisting and crushing progressed gradually with the number of Gelboflex test cycles and correspondingly the corrosion rate of the copper plates increased. Comparison of the corrosion rates of the copper plates kept in the pouches made of various commercial films with those obtained for the damaged SiO _x deposited nylon 6 films showed a clear relationship between the H₂ permeation rate of the films and the corrosion rate of the copper plates by H₂S.     

Three takes on telecom's troubles

Spectrum asked three IEEE members from the telecommunications sector to comment on the industry's current woes and prospects. Roch Guerin discusses bandwidth as a commodity and how to deal with it. The impact of technological change on telecommunications is enormous and calls for a shift in business models. Technology is making bandwidth a commodity and it should not matter who supplies it. Competition is vital and commodity providers must be decoupled from value providers. Frank Ferrante points out that the Year 2000 crisis resulted in manufacturers being deluged with orders for new upgraded systems. Vast sums were spent to meet the demand in time. However, when Y2K was over, production stayed high and inventories continued to build, while demand effectively stopped overnight. Dazzling new innovations are needed to compel the masses to spend and manufacturers must apply their resources to deliver quickly and efficiently. Jules A. Bellisio discusses the role of engineers in bringing new ideas to the market place. Many engineers have put together ventures for the sole purpose of attracting capital. The underlying technology and business propositions were there solely to lure the unsuspecting. By allowing engineers to use technology simply to cover for a scam, then the profession is also to blame for the current problems.     

The rank and kernel of extended 1-perfect /spl Zopf//sub 4/-linear and additive non-/spl Zopf//sub 4/-linear codes

A binary extended 1-perfect code of length n + 1 = 2/sup t/ is additive if it is a subgroup of /spl Zopf//sub 2//sup /spl alpha// /spl times/ /spl Zopf//sub 4//sup /spl beta//. The punctured code by deleting a /spl Zopf//sub 2/ coordinate (if there is one) gives a perfect additive code. 1-perfect additive codes were completely characterized and by using that characterization we compute the possible parameters /spl alpha/, /spl beta/, rank, and dimension of the kernel for extended 1-perfect additive codes. A very special case is that of extended 1-perfect /spl Zopf//sub 4/-linear codes.