Flammability and thermal stability studies of ABS/Montmorillonite nanocomposite

Acrylonitrile–butadiene–styrene (ABS)/montmorillonite nanocomposites have been prepared using a direct melt intercalation technique by blending ABS and organophilic clay of two different particle sizes: OMTa (5 µm) and OMTb (38 µm). Their structure and flammability properties were characterized by X‐ray diffraction, high resolution electronic microscopy (HREM), thermogravimetric analysis (TGA) and cone calorimeter experiments. The results of HREM showed that ABS/5 wt% OMTa nanocomposite was a kind of intercalated–delaminated structure, while ABS/5 wt% OMTb nanocomposite was mainly an intercalated structure. The nanocomposites showed a lower heat release rate peak and higher thermal stability than the original ABS by TGA and cone calorimeter experiments. Also, the intercalated nanocomposite was more effective than an exfoliated–intercalated nanocomposite in fire retardancy. Copyright © 2003 Society of Chemical Industry     

Hybrid switching and p-routing for optical burst switching networks

One promising switching technology for wavelength-division multiplexing optical networks is optical burst switching (OBS). However, there are major deficiencies of OBS. (1) The delay offset between a control message and its corresponding data burst is based on the diameter of a network. This affects network efficiency, quality-of-service, and network scalability.( 2) OBS adopts one-way resource reservation scheme, which causes frequent burst collision and, thus, burst loss. We address the above two important issues in OBS. In particular, we study how to improve the performance of delay and loss in OBS. To reduce the end-to-end delay, we propose a hybrid switching scheme. The hybrid switching is a combination of lightpath switching and OBS switching. A virtual topology design algorithm based on simulated annealing to minimize the longest shortest path through the virtual topology is presented. To minimize burst collision and loss, we propose a new routing algorithm, namely, p-routing, for OBS network. The p-routing is based on the wavelength available probability. A path that has higher available probability is less likely to drop bursts due to collision. The probability-based p-routing can reduce the volatility, randomness, and uncertainty of one-way resource reservation. Our studies show that hybrid switching and p-routing are complementary and both can dramatically improve the performance of OBS networks.     

辐射对血液流变效应的研究及动物全身照射后全血粘度的变化规律

本文结果表明经一次大剂量全身照射后的机体血液流变的主要特性为全血表观粘度先高粘后低粘的双向性变化,从照后第一天起即升高。随着放射病病程的发展,在早期有一个高粘峰,其峰均值比照前升高47.80％。但因不同动物、不同剂量、不同均速,不同血源而变化不同。     

STRUCTURE REPRESENTATION OF THE SPECIFIC FRACTIONS FROM PINGSHUO COAL

Basic data of four fractions, PM₁, PM₆, PM₇and PM₈, derived from Pingshuo bituminous coal were obtained by ultimate analyses, mean molecular weight measure, GC/MS, ¹³C-NM R, ¹H-NM R and FTIR technigues. A method of calculating the average molecular parameters of the fractions is introduced. Based on the calculated parameters, the molecular structure models of the fractions of PM₆, PM;and PM₈are constructed. Significant structural information about the saturated hydrocarbon and aromatic hydrocarbon with heteroatom groups is given also.     

27keV Ar~+斜入射时的Cu-Au合金溅射实验角分布

用27keV Ar~+分别在垂直和倾斜入射情况下,轰击了Cu-Au(30wt％)合金样品,测量了Cu和Au原子的溅射角分布。角分布是用卢瑟福背散射(RBS)技术分析Al捕获膜上的Cu-Au沉积成分而定量得到的。结果表明:(1)在Ar~+倾斜(θ=40°)入射时,Cu原子择优发射,且程度比垂直入射(θ_r=O°)时增强:(2)倾斜入射时,Cu原子的角分布显示出在接近于样品表面法线方向的发射角范围内(θ<45°),发射机率比垂直入射时减小。     

单齿泵削角的优化设计

给出了单齿泵削角的优化模型与计算实例，并对理论设计与实验进行了比较分析。     

微机模拟处理pH络合滴定法研究——Ⅱ.终点确定方法和最佳实验条件模拟估计程序

本文利用简便的滴定过程模型,确立了微机模拟处理实验数据,方便、准确地求解络合滴定等当点的方法。设计了最佳实验条件模拟估计程序。该法测定Zn~(2+),Pb~(2+),Cu~(2+),Fe~(3+)结果的相对误差Δ<1％。pH=6-7时,测定Ca~(2+)的相对误差为-1.61％;σ<0.001mmol,(N=5)。