Evolution of vinyl chloride conversion below critical micelle concentration: A response surface analysis

Utilizing response surface methodology, the conversion of vinyl chloride monomer (VCM) was monitored when the polymerization temperature, the type of surfactant, and the weight ratio of water‐to‐monomer (W/M) were taken as the emulsion polymerization variables. Because the homogeneous nucleation was found to be the dominant mechanism in VCM emulsion polymerization, irrespective of the surfactant concentration, the whole experiments have been carried out below critical micelle concentration of the used surfactants. Among all the studied variables, the polymerization temperature appeared as the most effective parameter; moreover, its interactive effect with W/M caused different trends in the alteration of final conversion being observed. Also, depending on the reaction temperature, the VCM conversion would be affected by the type of the surfactant used. Contrarily, simultaneous change in the type of surfactant and W/M revealed an insignificant effect on the evolution of VCM conversion. The optimization of final conversion of VCM was also accessible through contour plots of response surface methodology. It is worth noting that, taking a conventional approach into consideration, the alteration of VCM conversion seemed to be a monotonic function of temperature. J. VINYL ADDIT. TECHNOL., 21:157–165, 2015. © 2014 Society of Plastics Engineers     

Partial replacement of NR by GTR in thermoplastic elastomer based on LLDPE/NR through using reactive blending: Its effects on morphology,rheological, and mechanical properties

Attempts have been made to use different amount of ground tire rubber (GTR) powder as a partial substitute for natural rubber (NR) in thermoplastic elastomer based on linear low‐density polyethylene (LLDPE, 60 wt%) and NR (40wt%). Maleic anhydride (MA) and dicumyl peroxide (DCP) were used, during melt mixing of the compound, to modify GTR and vulcanize the rubber phases of the blends. Morphology of the blends was studied by scanning electron microscopy and rheological behavior investigated through rheomechanical spectroscopy. Mechanical properties of the blends were also measured, and the effect of GTR concentration on properties was evaluated. Obtained results showed that modification of GTR with MA and using DCP in the blends containing GTR improves the bonding between GTR and matrix. This leads to a distinctive rheological behavior and enhances tensile strength and elongation at break compared to its corresponding simple blend. It can be said that using of MA and DCP during melt mixing of thermoplastic elastomers based on LLDPE/NR containing GTR, concludes to a better dispersion of GTR and formation of morphology similar to that of a dynamic vulcanized thermoplastic elastomer, which improves interfacial bonding between phases and causes a dramatically increase in mechanical properties. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Irradiation grafting of methyl methacrylate monomer onto ultra‐high‐molecular‐weight polyethylene: An experimental design approach for improving adhesion to bone cement

The grafting of methyl methacrylate (MMA) onto ultra‐high‐molecular‐weight polyethylene (UHMWPE) and chromic acid etched UHMWPE was conducted with a preirradiation method in air in the presence of a Mohr salt and sulfuric acid. The grafted samples were characterized by Fourier transform infrared (FTIR) spectroscopy, a gravimetric method, differential scanning calorimetry, scanning electron microscopy (SEM), and interfacial bonding strength measurements. The FTIR results showed the presence of ether and carbonyl groups in the MMA‐grafted UHMWPE (MMA‐g‐UHMWPE) samples. The Taguchi experimental design method was used to find the best degree of grafting (DG) and bonding strength. The efficient levels for different variables were calculated with an analysis of variance of the results. SEM micrographs of MMA‐g‐UHMWPE samples showed that with increasing DG and chromic acid etching, the MMA‐g‐UHMWPE rich phase increased on the surface; this confirmed the high interfacial bonding strength of the grafted samples with bone cement. The grafting of the MMA units onto UHMWPE resulted in a lower crystallinity, and the crystallization process proceeded at a higher rate for the MMA‐g‐UHMWPE samples compared to the initial UHMWPE; this suggested that the MMA grafted units acted as nucleating agents for the crystallization of UHMWPE. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Design,optimization, and manufacturing of a multiple‐thickness profile extrusion die with a cross flow

This article presents a procedure to achieve a uniform outlet flow of molten polymer for a complex die profile with various thicknesses in die outlet cross section. According to a specific optimization methodology, the die was optimized based on varying die land length. The scope of this article includes: 3D flow simulation, optimization of the die velocity outputs based on the results of simulation process, and comparison of numerical predictions with the experimental data. Finally a significant result obtained by this work indicates higher ratio of the land length to the height of the zone with cross flow rather than the zones that are directly fed by the extruder. POLYM. ENG. SCI., 2010. © 2010 Society of Plastics Engineers.     

Compact bilayer substrate integrated waveguide leaky wave antenna with dumbbell‐shaped slot based on the TE20 mode

In this article, a compact dual layer leaky wave antenna array is simulated and constructed using the substrate integrated waveguide (SIW) based on the TE₂₀ mode at the X‐ and Ku‐bands. The proposed antenna is designed by creating dumbbell‐shaped slots on the upper layer of the SIW. These slots have increased the antenna bandwidth so that the proposed antenna has a bandwidth of 9.5 to 13.7 GHz and a fractional bandwidth of 36%. In addition, to excite the TE₂₀ mode, an SIW power divider is used in the feeding network of the antenna located in the bottom layer. Moreover, the gain and directivity are other advantages of the proposed antenna so that at 12.5 GHz the antenna peak gain reaches to 15.7 dB. Antenna beam scanning angle is from 5° to 81°. This antenna is simulated and analyzed by the CST Microwave Studio software. The obtained results from the antenna test lab confirm the simulation results.     

Ultra low voltage, high performance operational transconductance amplifier and its application in a tunable Gm-C filter

This paper presents an ultra low voltage, high performance Operational Transconductance Amplifier (OTA) and its application to implement a tunable Gm-C filter. The proposed OTA uses a 0.5 V single supply and consumes 60 μw. Employing special CMFF and CMFB circuits has improved CMRR to 138 dB in DC. Using bulk driven input stage results in higher linearity such that by applying a 500 mv_p-p sine wave input signal at 2 MHz frequency in unity gain closed loop configuration, third harmonic distortion for output voltage is −46 dB and becomes −42.4 dB in open loop state for 820 mv_p-p output voltage at 2 MHz. DC gain of the OTA is 47 dB and its unity gain bandwidth is 17.8 MHz with 20 pF capacitance load due to both deliberately optimized design and special frequency compensation technique. The OTA has been used to realize a wide tunable Gm-C low-pass filter whose cutoff frequency is tunable from 1.4 to 6 MHz. Proposed OTA and filter have been simulated in 0.18 μm TSMC CMOS technology with Hspice. Monte Carlo and temperature dependent simulation results are included to forecast the mismatch and temperature effects after fabrication process.     

Combustion characteristics of candles made from hydrogenated soybean oil

Hydrogenated soybean oil, referred to as soywax by candle makers, is a renewable and biodegradable alternative to paraffin wax in candle manufacturing. Soywax was investigated for its tendency to produce soot as well as potentially harmful organic volatiles (acrolein, formaldehyde, and acetaldehyde) during combustion. Beeswax and paraffin candles were used as references. A considerable amount of soot was produced from the combustion of paraffin candles, but little or none was observed from soywax candles. Compared to paraffin candles, soywax candles burned at a significantly slower rate and required less air. Small amounts of formaldehyde were detected and quantified in the fumes of burning paraffin candles. However, formaldehyde, peaks found in the chromatograms of soy- and beeswax candles were similar to or slightly higher than that of the blank. Since soywax candles exhibited burning properties similar to those of beeswax candles, soywax shows promise in candle applications.     

Generalized Storage Equations for Flood Routing with Nonlinear Muskingum Models

Water Resources Management - The nonlinear Muskingum model is a leading method for hydrologic routing. The efficiency of the nonlinear Muskingum model for routing of hydrograph outflow has been...     

SIW Corporate-Feed Network for Circular Polarization Slot Array Antenna

Wireless Personal Communications - In this paper, multilayer feeding network for linear slot array antenna is studied. A substrate integrated waveguide (SIW) corporate-feed network for linear slot...     

Effects of Previous Gutting on Biochemical Changes and Profile of Long‐Chain Polyunsaturated Fatty Acids in Cold‐Smoked Kutum (Rutilus frisii kutum) Stored at Room Temperature (25 ± 2C)

Previous gutting was applied to fresh kutum (Rutilus frissi kutum) to study the effects of cold smoking on the changes of rancidity and fatty acid (FA) content of the gutted and ungutted smoked kutum stored at room temperature (25 ± 2C) for 60 days. To do so, proximate (protein, ash, moisture and lipid), chemical (peroxide value [PV], thiobarbituric acid‐index [TBA‐i], total volatile basic nitrogen [TVB‐N] and FA profile) and pH analyses were carried out. The ungutting of kutum before smoking resulted in a higher degree of bacterial spoilage and oxidation during storage at room temperature, based on the results obtained from PV, TBA‐i, TVB‐N and FA content analyses. Moreover, pH as a critical factor on food spoilage showed a less decrease in smoked ungutted kutum during the 60‐day storage. It is concluded that the gutting of kutum before cold smoking is recommended as a pretreatment for storage at room temperature.