Sono-Fenton regeneration of granular activated carbon saturated with Rhodamine B: Optimization using response surface methodology

This study investigated the combination of chemical and ultrasonic regeneration (Sono-Fenton), used for regenerating granular activated carbon (GAC) saturated with Rhodamine B (RB). This process was modeled and optimized using response surface methodology (RSM) based on central composite design (CCD). Effective parameters on regeneration efficiency such as pH, concentration of hydrogen peroxide (H₂O₂), and time of ultrasonic irradiation were optimized and modeled using the reduced quadratic method. The fitness of the model was checked by the determination coefficient (R²?=?0.9978). At optimum condition, the effective parameters of pH?=?3.84, concentration of H₂O₂?=?38.28 (mM), and time of ultrasonic irradiation?=?23.11(min), maximum regeneration efficiency (87.88%) was achieved, the results of which were obtained after four-time sequential adsorption–regeneration cycles were acceptable. Desorption and degradation of RB were conducted through the generation of active species, including hydroxyl radicals and high-energy ultrasound. The regeneration efficiency was increased using this combination method. In conclusion, the Sono-Fenton method is suggested to be used more widely in regeneration processes.     

The effect of pH,salts and sugars on the rheological properties of cress seed (Lepidium sativum) gum

Effect of shear rate (15–600 s^?1), gum concentration (1–2%), pH (3–9), sucrose (10–40%), lactose (5–15%), NaCl (100–300 mm ) and CaCl₂ (5–50 mm ) was evaluated on apparent viscosity (η_a), flow behaviour index (n), consistency coefficient (K) and yield stress (τ₀) indices of cress seed gum (CSG) solutions. Different rheological models were used to fit the experimental data, although the Herschel–Bulkley model was found the best model. An increase in gum concentration led to an increase in τ₀, η_a, and k and a decrease in n values. The addition of salts lowered the k value; however, the n value showed slight significant change. The presence of sugar resulted in the enhancement of n, k, τ₀ and η_ap values. The existence of yield stress and pseudoplastic behaviour of CSG, its stability against salts, wide range of pH and synergic effect of sugar make it a good thickener and stabiliser in food formulations.     

Effect of polyaniline–montmorillonite nanocomposite powders addition on corrosion performance of epoxy coatings on Al 5000

A series of polyaniline (PANI)/montmorillonite (MMT) nanocomposite materials has been successfully prepared by in-situ emulsion polymerization in the presence of inorganic nanolayers of clay with camphorsulfonic acid (CSA) and ammonium peroxydisulfate (APS) as surfactant and initiator, respectively. The nanocomposite materials were characterized by Fourier Transformation Infrared (FTIR) spectroscopy, X-ray diffraction (XRD) and scanning electron microscopy (SEM). Epoxy resin was used as a binder for the nanocomposites in order to obtain a thick and uniform coating. In order to understand the effect of MMT and PANI on the corrosion inhibition performance of the epoxy coatings in 3.5% saline solution at 65 °C, the epoxy (E), epoxy blend with polyaniline (EP), epoxy blend with polyaniline and MMT (EPM) coatings were investigated by electrochemical impedance spectroscopy (EIS). The results showed that EPM coatings with 5% clay on pretreated aluminum by anodizing were much superior in corrosion protection, with respect to the other samples. Incorporation of PACN nanocomposites inside the epoxy significantly increases the resistance of the coating in comparison to the other coatings in 3.5% saline solution at 65 °C. These phenomena can be attributed to specific morphology of the nanocomposite.     

Magnetic behavior of nickel–bismuth ferrite synthesized by a combined sol–gel/thermal method

The bulk NiFe_2?xBi_xO₄ ferrites with various Bi³⁺ concentration (x=0, 0.1, 0.15) were synthesized via sol–gel procedure, starting from nickel, bismuth and iron nitrate powders, followed by the conventional thermal treatment. The structural and magnetic properties of the as-prepared ferrites were studied by means of X-ray diffraction, alternating gradient force magnetometry and Faraday balance. The anisotropy constant was determined by the law of approach to saturation (LAS) model. An increasing Bi³⁺ concentration in NiFe_2?xBi_xO₄ leads to a decrease in the saturation magnetization, Néel temperature and the anisotropy constant of the material.     

Analysis and optimization of laminated composite circular cylindrical shell subjected to compressive axial and transverse transient dynamic loads

Optimization is one of the important stages in the design process. In this paper the genetic algorithms method is applied for weight and transient dynamic response and two constraints including critical buckling loads and principle strains optimization of laminated composite cylindrical shells. The multi-objective function seeks the minimum structural weight and transient dynamic response. Nine design variables including material properties (fibre and matrix), volume fraction of fibre, fibre orientation and thickness of each layer are considered. In analytical solution, vibration of composite circular cylindrical shells are investigated based on the first-order shear deformation shell theory. The boundary conditions are assumed to be fully simply support. The dynamic response of the composite shells is studied under transverse impulse and axial compressive loads. The modal technique is used to develop the analytical solution of the composite cylindrical shell. The solution for the shell under the given loading conditions can be found using the convolution integrals. An example of simply supported laminated composite cylindrical shells is given to demonstrate the optimality of the solution obtained by the genetic algorithms technique. Results are shown that the weight coefficient of multi-objective function and the type of the constraints have considerable effect on the optimum weight and dynamic response.     

Effect of carbon steel microstructures and molecular structure of two new Schiff base compounds on inhibition performance in 1 M HCl solution by EIS

In this investigation, attempts have been made to study the inhibitive effect of N,N′-ortho-phenylen acetyle acetone imine (S1) and 4-[(3-{[1-(2-hydroxy phenyl) methylidene] amino} propyl] ethanemidol]-1,3-benzenediol (S2) in the concentration range of 50–400 ppm for mild steel with two different microstructures resulted from two different heat treatments (annealed (A) and quenched and tempered (Q&T)) in 1 M hydrochloric acid by ac impedance spectroscopy. The tests were conducted in acid solutions in the absence and presence of different concentrations of S1 and S2 Schiff bases for both microstructures. A sole time constant was observed from Bode-phase angle plots in the presence of inhibitors which reveals that the action of inhibitors is through adsorption on the surface. The charge transfer resistance and inhibition efficiency increases with the increase in Schiff bases concentration for both microstructures. The perlite samples in the absence of inhibitors in 1 M hydrochloric acid indicated slightly less corrosion than martensite ones, which was because of more protective oxide layers. Furthermore in the presence of S1 and S2, these samples showed better adsorption than martensite one. Schiff base S1 showed a better inhibition against corrosion in comparison with S2. Both S1 and S2 adsorbed on steel surface according to a Langmuir adsorption isotherm model. The associated Gibbs free energies for S1 on both microstructures are more than S2.     

Combining continuous catalytic regenerative naphtha reformer with thermally coupled concept for improving the process yield

Advancements in the catalytic naphtha reforming process, as one of the main processes in petrochemical industry, contributed to development of continuous catalytic regenerative naphtha reformer units. Increasing the yield of aromatic and hydrogen as well as saving the energy in this process through the application of thermal coupling technique is a potentially interesting idea. This novel idea has been assessed in this paper. In the proposed configuration, continuous catalyst regeneration naphtha reforming process is coupled with hydrogenation of nitrobenzene in a two co-axial reactor separated by a solid wall, where the generated heat in nitrobenzene hydrogenation reaction transfers to naphtha reforming reaction medium through the surface of the tube. A steady-state, homogeneous, two-dimensional model is used to describe the performance of this configuration and a kinetic model including 32 pseudo-components with 84 reactions is considered for naphtha reforming reaction. After validating the model with the commercial data of a domestic plant, the obtained results of coupled reactor are compared by the conventional one. The obtained results show the superiority of CCR coupled reactor against the conventional one.     

Thermal Stability of <Emphasis Type="Italic">α</Emphasis> Phase of Titanium by Using X-Ray Diffraction

At room temperature and ambient pressure, crystalline titanium has a hexagonal-close-packed (hcp) lattice and at high temperature appears as a body-centered-cubic (bcc) structure. In fact, the phase transitions of titanium have been investigated under various pressures and temperatures. However, the phase transitions of titanium have been mostly reported at high pressure, while less attention has been paid to various ranges of high temperature. Therefore, in this study, we have considered the thermal stability of α phase of titanium by using X-ray diffraction (XRD) at high temperature. The observed experimental results of the diffraction show that the stability range of α phase varies between room temperature to around 923 K (650 °C).     

Variable impedance actuators: A review

Variable Impedance Actuators (VIA) have received increasing attention in recent years as many novel applications involving interactions with an unknown and dynamic environment including humans require actuators with dynamics that are not well-achieved by classical stiff actuators. This paper presents an overview of the different VIAs developed and proposes a classification based on the principles through which the variable stiffness and damping are achieved. The main classes are active impedance by control, inherent compliance and damping actuators, inertial actuators, and combinations of them, which are then further divided into subclasses. This classification allows for designers of new devices to orientate and take inspiration and users of VIA’s to be guided in the design and implementation process for their targeted application.     

Increasing image compression rate using steganography

The goal of image compression is to remove the redundancies for minimizing the number of bits required to represent an image while steganography works by embedding the secret data in redundancies of the image in invisibility manner. Our focus in this paper is the improvement of image compression through steganography. Even if the purposes of digital steganography and data compression are by definition contradictory, we use these techniques jointly to compress an image. Hence, two schemes exploring this idea are suggested. The first scheme combines a steganographic algorithm with the baseline DCT-based JPEG, while the second one uses this steganographic algorithm with the DWT-based JPEG. In this study data compression is performed twice. First, we take advantage of energy compaction using JPEG to reduce redundant data. Second, we embed some bit blocks within its subsequent blocks of the same image with steganography. The embedded bits not only increase file size of the compressed image, but also decrease the file size further more. Experimental results show for this promising technique to have wide potential in image coding.