一种协调的科技文献分类方法

科技文献之间的相互引证关系反映了一种科学交流活动,显示了科学文献之间(甚至是学科之间)的内在联系,而通过追溯文献之间的这种关系,可以改善和提高传统的基于内容的科技文献的分类的方法。论文利用有相互引证关系,有同引关系,以及有耦合关系的两篇文献一般是属于同一类的这一特点,提出了文献之间的引用相似度,同引相似度,耦合相似度这三个概念,再利用这三个概念生成了文献之间的“结构相似度”,并将它用于K-NN分类法中得出一种基于结构的分类法。最后,论文将这种基于结构的分类法和基于内容的NaveBayes分类法结合起来提出了一种新的协调分类法。     

The thermal behavior of mechanically activated galena by thermogravimetry analysis

The thermal decompositions of mechanically activated and nonactivated galenas were studied by thermogravimetry analysis (TGA) at the heating rate of 10 K min⁻¹ in argon. Results indicate that the initial temperature of thermal decomposition (abbreviated as T _di) in the TGA curves for different galenas decreases gradually with increased grinding time. The specific granulometric surface area (S _G), the structural disorder, and the content of elemental sulfur of mechanically activated galenas were analyzed by an X-ray diffraction (XRD) laser particle-size analyzer, XRD analysis, and the gravimetric method, respectively, which shows that the specific granulometric surface area of mechanically activated galenas remains almost constant after a certain grinding time, but the lattice distortions (ε) rise, the crystallite sizes (D) decrease, and the elemental sulfur contents of mechanically activated galenas increase with increased grinding time. The results imply that the decrease of the initial temperature of thermal decomposition in the TGA curves for mechanically activated galenas is mainly caused by the increase of lattice distortions, and the formation of new dangling bonds resulted from the production of elemental sulfur of mechanically activated galenas with increased grinding time. Finally, the differences in the thermal-decomposition reactivity between nonactivated and mechanically activated galenas were also discussed.     

On the elemental effect of AlCoCrCuFeNi high-entropy alloy system

The AlCoCrCuFeNi high-entropy alloy system was synthesized using a well-developed arc melting and casting method. Their elemental effect on microstructures and hardness was investigated with X-ray diffraction, scanning electron microscopy and Vickers hardness testing. The alloys exhibit quite simple FCC and BCC solid solution phases. Co, Cu and Ni elements enhance the formation of the FCC phase while Al and Cr enhance that of the BCC phase in the alloy system. BCC phases form a spinodal structure during cooling. Copper tends to segregate at the interdendrite region and forms a Cu-rich FCC phase. Low copper content renders the interdendrite as a thin film and the as-cast structure like recrystallized grain structure. The formation of BCC phases significantly increases the hardness level of the alloy system. The strengthening mechanism is discussed.     

ZJ510L-B汽车用高强度热轧板的试制

珠钢150t电弧炉-LF(VD)-CSP(紧凑式带材生产)流程试生产的5～8mm ZJ510L-B(0．16C--1．22Mn)汽车用高强度热轧板的铁素体晶粒尺寸为6．0～9．2μm，带状组织为1．5～2．5级，强度极限σb562～610MPa，延伸率δ5 32．0％～38．6％。文中还分析和提出了带状组织的形成原因和改进措施。     

Preparation of Compound Ultrafine CeO2 by Wet-Solid-Phase Mechanochemical Modification

To satisfy practical requirements from industrial applications, an alternate route for synthesis compound ultrafine CeO2 powders by wet-solid-phase mechanochemical modification using industrial grade hydrated cerium carbonate as raw material was proposed.The effect of modifier reaction percentage, reaction time, calcining temperature and modifier amount on particle size, density, suspensibility, and hardness of compound CeO2 powder was investigated.The phase evolutions of preparation process were characterized by XRD.SEM micrograph of the final product shows that compound CeO2 powders obtained are well-dispersed, spherically-shaped, uniformly-sized and submicron-sized particles.The method is readily available in raw material, low in cost, simple in process, and has great potential for industrialization.The compound CeO2 powders of different physical properties can be synthesized by controlling the above-mentioned influence factors in preparation process.     

单壁碳纳米管的制备及生长特性研究

采用Fe/MgO作为催化剂 ,催化裂解CH4制备了较纯的单壁碳纳米管 ,用TEM和Raman对碳纳米管进行了表征 ,对不同生长温度下制备的碳纳米管Raman径向呼吸振动峰 (RBM)进行了分析 ,研究了生长温度对单壁碳纳米管生长特性和结构特性的影响     

Industrialization of High Performance Sintered NdFeB Magnets

Sintered Nd-Fe-B magnet was manufactured by advanced equipment via a SC (Strip casting) technology.It has integrative performance.     

A single-grain approach applied to the modeling of recrystallization kinetics for cold-rolled single-phase metals

A comprehensive model for the recrystallization kinetics is proposed which incorporates both microstructure and the textural components in the deformed state. The model is based on the single-grain approach proposed previously. The influence of the as-deformed grain orientation, which affects the stored energy via subgrain size and sub-boundary misorientation, is taken into account. The effects of the deformed grain geometry, the nucleation-site density, and the initial grain size prior to deformation on the recrystallization kinetics are assessed. The model is applied to the recrystallization kinetics of a cold-rolled AA1050 alloy.     

自蔓延高温合成TiNi多孔体合金

为了开发新型的生体材料，本文对自蔓延高温合成TiNi多孔体合金——人造骨材料进行了研究。以单质钛粉和镍粉作原料，在氩气保护条件下，采用预热点燃模式和热爆模式制得了不同形态的多孔TiNi形状记忆合金。采用SEM和XRD分析了样品的孔洞特征和相组成，测试了其力学性能，并研究了合成条件参数与样品表面形貌和孔隙状态之间的关系。结果表明，用SHS法制备TiNi多孔体合金是可行的。