Prediction of the maximum spoutable height in spout-fluid beds

The development of the semi-theoretical correlation in Hadzisdmajlovic et al. (1983) for predicting the maximum spoutable height in a spout-fluid bed, is observed to involve certain discrepancies. Based on their experimental data, a new correlation is proposed.     

Chemical control of superconducting properties of (Y,Ca)(Sr,Ba)2Cu2.7Ga0.3O7−δ

The partial substitution of Ga at the Cu(1) (chain) sites of the YBa₂Cu₃O₇ structure allows synthesis at ambient pressure of Ba-free analogs, e.g., YSr₂Cu_2.7Ga_0.3O_7?δ . Materials with this composition have been found to be nonsuperconducting, but superconductivity has been induced by one or more of the following methods: Ca substitutions at the Y site; Ba substitutions at the Sr site; annealing in high-pressure oxygen. The influence of these chemical manipulations onT _c has been monitored and all methods have been found to enhanceT _c . The electronic effects of Ba substitutions have been deduced indirectly using powder neutron diffraction, and such substitutions appear to result in a redistribution of hole density into the Cu(1) sites from the superconducting CuO₂ planes.     

Prediction of thermal expansion coefficients of plain weave fabric composites

Three plain weave fabric composite analysis models are presented for the prediction of the on-axes thermal expansion coefficients. These are two-dimensional models in the sense that the actual strand cross-sectional geometry, strand undulation and the presence of a gap between the adjacent strands are taken into account. In the first two models, termed refined models, the representative unit cell is discretised into slices and elements and analysed. In the third method, a closed-form solution is presented. In this case, the representative unit cell is idealised as a crossply laminate and analysed. The relative merits and demerits of the models are also discussed. The predicted results are compared with the experimental values. A good correlation is observed.     

Experimental and Analytical Behavior of Carbon Fiber-Based Rods as Flexural Reinforcement

This paper presents the results of an experimental and analytical comparison of a study on the flexural behavior of concrete beams reinforced with sandblasted carbon fiber-based composite rods. Twelve beams, including three control beams reinforced with steel, were tested for strength, deformation, and failure characteristics. Analytical comparisons included the generation of the theoretical strength and moment curvature relations. Experimental data from pullout tests indicated that bonding of sandblasted rods is not a major concern. However, excessive deformation in achieving the predicted moment capacity could be a limiting factor in the design of these beams.     

Probabilistic reliable dissemination in large-scale systems

The growth of the Internet raises new challenges for the design of distributed systems and applications. In the context of group communication protocols, gossip-based schemes have attracted interest as they are scalable, easy to deploy, and resilient to network and process failures. However, traditional gossip-based protocols have two major drawbacks: 1) they rely on each peer having knowledge of the global membership; and 2) being oblivious to the network topology, they can impose a high load on network links when applied to wide-area settings. In this paper, we provide a theoretical analysis of gossip-based protocols which relates their reliability to key system parameters (the system size, failure rates, and number of gossip targets). The results provide guidelines for the design of practical protocols. In particular, they show how reliability can be maintained while alleviating drawback by: 1) providing each peer with only a small subset of the total membership information and drawback; and 2) organizing members into a hierarchical structure that reflects their proximity according to some network-related metric. We validate the analytical results by simulations and verify that the hierarchical gossip protocol considerably reduces the load on the network compared to the original, non-hierarchical protocol.     

Properties of ligno‐cellulose fiber Hildegardia

Studies on some properties such as the density, the degradation temperatures, the morphology and the spectral features of the ligno‐cellulose fiber Hildegardia were carried out in both untreated and alkali treated form. The fibers are found to have good morphology and moderate initial and final degradation temperatures. On alkali treatment, the lignin was found to be eliminated. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2216–2221, 2002     

Microstructural effects on the tensile properties and deformation behavior of a Ti-48Al gamma titanium aluminide

The effects of microstructure on the tensile properties and deformation behavior of a binary Ti-48Al gamma titanium aluminide were studied. Tensile-mechanical properties of samples with microstructures ranging from near γ to duplex to fine grained, near- and fully-lamellar were determined at a range of temperatures, and the deformation structures in these characterized by transmission electron microscopy (TEM). Microstructure was observed to exert a strong influence on the tensile properties, with the grain size and lamellar volume fraction playing connected, but complex, roles. Acoustic emission response monitored during the tensile test revealed spikes whose amplitude and frequency increased with an increase in the volume fraction of lamellar grains in the microstructure. Analysis of failed samples suggested that microcracking was the main factor responsible for the spikes, with twinning providing a minor contribution in the near-lamellar materials. The most important factor that controls ductility of these alloys is grain size. The ductility, yield stress, and work-hardening rate of the binary Ti-48Al alloy exhibit maximum values between 0.50 and 0.60 volume fraction of the lamellar constituent. The high work-hardening rate, which is associated with the low mobility of dislocations, is the likely cause of low ductility of these alloys. In the near-γ and duplex structures, slip by motion of 1/2<110] unit dislocations and twinning are the prevalent deformation modes at room temperature (RT), whereas twinning is more common in the near- and fully-lamellar structures. The occurrence of twinning is largely dictated by the Schmid factor. The 1/2<110] unit dislocations are prevalent even for grain orientations for which the Schmid factor is higher for <101] superdislocations, though the latter are observed in favorably oriented grains. The activity of both of these systems is responsible for the higher ductility at ambient temperatures compared with Al-rich single-phase γ alloys. A higher twin density is observed in lamellar grains, but their propagation depends on the orientation and geometry of the individual γ lamellae. The increase in ductility at high temperatures correlates with increased activity of 1/2<110] dislocations (including their climb motion) and twin thickening. The role of microstructural variables on strength, ductility, and fracture are discussed. This article is based on a presentation made in the symposium entitled “Fundamentals of Structural Intermetallics,” presented at the 2002 TMS Annual Meeting, February 21–27, 2002, in Seattle, Washington, under the auspices of the ASM and TMS Joint Committee on Mechanical Behavior of Materials.     

Microstructure and Dielectric Characteristics of (PbxBa0.5−xSr0.5)TiO3 Ceramics

Microstructural and dielectric properties of the Pb _x Ba _0.5__x —Sr_0.5TiO₃ system have been studied. It is found that this system forms a solid solution in the entire composition range (0.0≤ x ≤0.5) and is cubic for the x = 0, 0.1, and 0.2 compositions and tetragonal for other compositions. Measurements of the dielectric constant as a function of temperature reveal that this material is ferroelectric at room temperature for the x > 0.2 compositions and has a broad paraelectric-ferroelectric transition region. No shift in the dielectric maxima was noted; however, there is a slight spread in the dielectric constant with frequency for the x = 0.4 composition. A quantitative model to mathematically analyze the effect of composition fluctuations on the dielectric broadening for a ternary system is presented. Transmission electron microscopic studies reveal the presence of 90° ferroelectric domains oriented along the {01     } planes for the x = 0.3 and 0.4 compositions.