Fabrication of multi-walled carbon nanotube reinforced polyelectrolyte hollow nanofibers by electrospinning

Hybrid hollow multi-walled carbon nanotubes (MWCNTs)/polyelectrolytes (PE) nanofibers were prepared by a combination of the electrospinning method and layer-by-layer (LbL) technique. The mixed polystyrene (PS)/MWCNTs nanofibers were obtained by electrospinning method, which were employed as templates to self-assembly multilayered polyelectrolytes by LbL technique. Hollow MWCNTs/PE nanofibers were obtained by selectively removed part of the template: PS, which is confirmed by Raman spectra, transmission electron microscopy (TEM) and scanning electron microscopy (SEM).     

MIMO系统中简单的扩展空时块编码分集技术研究

本文提出一种多输入多输出（MIMO）天线系统中简单的扩展空时块编码（SSTBC）分集技术，采用沃尔什码来区分各天线发送数据子流。采用这种方法，在系统带宽一定时，不降低发送信息速率，同时接收机简单。不同天线的发送信息经过了所有收一发天线对之间的空间子信道，获得了所有路径的部分空间分集增益，仿真结果表明，这种增益的获得不受限于接收分集阶数，并且随发射天线的增加以一定的线性关系增加。     

离散事件系统状态反馈控制的几何理论的进一步拓广

本文研究了定义在状态-事件序列上的谓词的离散事件系统的状态反馈控制问题。离散事件系统的数学模型是自动机。状态反馈与闭环过程的关系及许多基本的几何性质得到了详细的阐明;在这些几何背景下,解决了离散事件系统状态反馈控制的拓广问题,包括关于简单谓词与一般谓词的问题。     

绍兴市城区河道整治工程若干问题初探

通过对绍兴城区环城河、大环河、古运河、古城河等河道整治工程内容和整治成效的分析，总结了绍兴城区河道整治的5大特点，针对河道建设中存在的有关问题，提出了今后城市河道整治的4条具体措施。     

SU-8 3D microoptic components fabricated by inclined UV lithography in water

Out-of-plane microlenses and microoptical fiber holder are two of the most important components for building an integrated microoptic system with a precise alignment accuracy. In this paper, a simple and convenient method to fabricate these components from SU-8 by using inclined UV lithography in water is proposed. It consists of two perpendicular exposures in SU-8 at ±45°. DI water possesses a low absorption coefficient and a moderate and stable value of refractive index in near UV. Using water, the exposure angle in SU-8 can be increased to 50° from 35° in air necessary to pattern the desired 45° slope of the sidewalls. The principle of the proposed technique and the detailed fabrication process of the microoptic components will be presented. The integratability of the fabricated components was demonstrated by the fabrication of the microoptical fiber holder with a pre-aligned out-of-plane microlens.     

多孔薄膜荫罩热变形的有限元仿真设计

荫罩的热变形使电子束产生着屏偏移 ,进而导致了色纯变坏。本文采用大型软件ANSYS对 1 5英寸荫罩进行了热变形的有限元仿真 ,从而得到了电子束的着屏偏移。建立了包括阴极射线管 (CRT)里所有部件的完整的有限元模型。荫罩被建为无孔连续薄壳的模型 ,对它的表面导热系数和表面弹性模量作了等效的计算。考虑了弹簧片的预应力以及弹簧片和销钉的连接。这样可使我们的分析模型更接近真实情况。本文给出了 50 0、1 0 0 0、1 0 0 0 0s时的热变形和电子束着屏偏移。分析表明 :电子束着屏偏移的最大值发生在 50 0s左右。利用这种分析方法及研究结果可指导新型荫罩的设计和研制。     

基体温度对磁控溅射沉积ZAO薄膜性能的影响

利用中频交流磁控溅射方法 ,采用氧化锌铝陶瓷靶材 [w(ZnO) =98%、w(Al2 O3 ) =2 % ]制备了ZAO(ZnO∶Al)薄膜 ,观察了基体温度对ZAO薄膜的晶体结构、电学和光学性能的影响 ,采用X射线衍射仪对薄膜的结构进行了分析 ,采用光学分度计和电阻测试仪测量了薄膜的光学、电学特性 ,采用霍尔测试仪测量了薄膜的载流子浓度和霍尔迁移率。结果表明 :沉积薄膜时的基体温度对薄膜的结构、结晶状况、可见光透射率以及导电性有较大的影响。当基体温度为 2 5 0℃ ,Ar分压为 0 8Pa时 ,薄膜的最低电阻率为 4 6× 10 -4Ω·cm ,方块电阻为 35Ω时 ,可见光 (λ =5 5 0nm)透射率高达 92 0 %。     

Ring‐opening polymerization of D,L‐lactide by rare earth 2,6‐dimethylaryloxide

Ring‐opening polymerization of D,L ‐lactide (LA) has been successfully carried out by using rare earth 2,6‐dimethylaryloxide (Ln(ODMP)₃) as single component catalyst or initiator for the first time. The effects of different rare earth elements, solvents, monomers and catalyst concentration as well as polymerization temperature and time on the polymerization were investigated. The results show that La(ODMP)₃ exhibits higher activity to prepare poly(D,L ‐lactide) (PLA) with a viscosity molecular weight of 4.5 × 10⁴ g mol^?1 and the conversion of 97 % at 100 °C in 45 min. The catalytic activity of Ln(ODMP)₃ has following sequence: La > Nd > Sm > Gd > Er > Y. A kinetic study has indicated that the polymerization is first order with respect to both monomer and catalyst concentration. The apparent activation energy of the polymerization of LA with La(ODMP)₃ is 69.6 kJ mol^?1. The analyses of polymer ends indicate that the LA polymerization proceeds according to ‘coordination–insertion’ mechanism with selective cleavage of the acyl–oxygen bond of the monomer. Copyright © 2004 Society of Chemical Industry     

Vibration cavitation behaviour of selected Ni-Mn-Ga alloys

Vibration cavitation erosion tests were carried out on Ni-Mn-Ga alloys of three different crystal structures: (1) the cubic austenite, (2) the non-modulated tetragonal martensite (T) and (3) the five-layered martensite (5M). All Ni-Mn-Ga alloys exhibited cavitation behaviour characterized by a step-wise curve of mass loss versus test time. This behaviour is correlated to the microstructural nature of the alloys as well as the surface conditions of the pre-test samples. The type and concentration of the defects at the surfaces were critical to the cavitation resistance of the alloys. The best cavitation resistant alloy was of a cubic austenitic structure, followed with the alloy of a tetragonal T-martensite. The largest material loss was found in the alloy with a 5M martensite. All the studied Ni-Mn-Ga alloys had an excellent cavitation resistance compared to that of the reference stainless steel, and they even excelled some NiTi alloys found in literature. This may be due to the superelasticity of the cubic austenite and the twinning of the martensitic phases.