帧中继交换技术

本文论述了帧中继交换的概念、标准，结构、特点网络式样及在互连网中的应用。     

短模型上的明渠非恒定流试验

水工整体模型试验中,明渠非恒定流至今大多被简化为恒定流,而效果有时并不理想。本文指出,只要设置固定式曲线尾门,并有必要的动态量测设备,便可模拟原型非恒定流;即使模型偏短,也能得出比恒定流试验更接近原型的成果。在同一模型上,既做恒定流试验,又进行必要的非恒定流试验,二者相辅相成,必将有助于试验水平的提高。作为例证,本文介绍了泄洪调度导致航道水面波动的一项试验成果,并以岩基冲刷、通航水流条件、围堰过水、河床冲淤等研究课题为例,讨论了采用“短模型非恒定流试验方式”的必要性与可行性。     

The relation between luminous properties and oxygen content inZnS:TbOF thin-film electroluminescent devices fabricated byradio-frequency magnetron sputtering method

The purpose of this paper is to study the relationship between the oxygen concentration and brightness degradation in ZnS:TbOF green thin-film electroluminescent (EL) devices. The characteristics including crystallinity, optical, and electrical properties were discussed. The brightness-voltage (B-V) measurement results shelved that with higher oxygen-content in ZnS:TbOF phosphor layer, lower brightness was measured. It was consistent with the poor crystallinity, worse photoluminescent intensity, and easier to get moisture in the oxygen-rich (O/Tb>1) phosphor film. Furthermore, deep level transient spectroscopy (DLTS) measurements identified that when the O/Tb ratio was greater than 1, the oxygen-related deep hole traps E_H1 and/or E_H2 could be detected in the ZnS:TbOF phosphor layer. These E _H1 and/or E_H2 traps were believed to be the main killers for the brightness of the device since they capture most of the holes from the generated electron-hole pairs. This evidence strongly supports that the modified energy transfer model is more dominant than direct impact excitation during the luminescent process     

In-laboratory removal of femoral sheath following protamine administration in patients having intracoronary stent implantation

Two hundred twenty-eight patients with successful coronary stent implantation were randomized either to protamine administration and femoral sheath removal (group I, n = 117) or no heparin neutralization and delayed sheath removal (group II, n = 111). The hospital stay after treatment was shorter in patients receiving protamine; therefore, protamine use for neutralizing circulating heparin may be safely administered immediately after stent implantation.     

气—液式热管换热器在硫酸工业中的应用研究

本文研制的气－液式热管换热器应用于硫酸生产中ＳＯ３气体的余热回收。它具有传热性能好、流动阻力小、寿命长、体积小、节能效果显著和易清垢等优点。     

变结构变参数设计方法及其在机械CAD中的应用

提出了一种新颖的机械结构设计思想－变结构变参数设计方法，并结合实例，阐述了变结构变参数设计的概念、原则、实施措施和意义。由此对Ｉ－ｄｅａｓ软件包进行了二次开发，编制了发动机曲轴专用ＣＡＤ软件程序，并用某型号发动机曲轴进行了验证。     

Assessment model of dam operation risk based on monitoring data

Although the dams produce remarkable social and economic benefits, the threat made by unsafe dams to the life and property of people who live in the lower river area is un-negligible. Based on the monitoring data which reflect the safety condition of dams, the risk degree concept is proposed and the analysis system and model for evaluating risk degree (rate) are established in this paper by combining the reliability theory and field monitoring data. The analysis method for risk degree is presented based on Bayesian approach. A five-grade risk degree system for dam operation risk and corresponding risk degree is put forward according to the safety condition of dams. The operation risks of four cascade dams on some river are analyzed by the model and approach presented here and the result is adopted by the owner.     

新增探明储量的经济可采储量计算方法

提出了新增探明储量有无经济可采储量的判别方法。在此基础上，通过对立已开发油田技术可采储量经济转化率与油藏空气渗透率的相关关系式和图版，根据储层的空气渗透率，计算新增探明储量的经济转化率和经济可采储量。该方法参数易取，计算简便，对于快速、准确计算新增探明储量的经济可采储量具有重要意义。     

薄板坯连铸连轧工艺对铌微合金化高强度钢组织和性能的影响

首先建立薄板坯连铸连轧工艺的试验室模拟技术，并运用该模拟技术，研究薄板坯连铸连轧工艺(CSP)和传统板坯再加热工艺(TRP)两种工艺对铌微合金化高强度钢的显微组织和力学性能的影响。研究结果表明：CSP钢的晶粒细化效果不如TRP钢，两者的平均铁素体晶粒尺寸分别为8．17μm和6．30μm。在CSP试验钢板中铌的析出量较大，特别是在铁素体中细小颗粒的铌的析出物较多，沉淀强化效果较强。CSP试验钢的σ0.5和σb分别较TRP工艺低约40MPa和约25MPa，同时其低温冲击韧性较好，FATT温度较低。     

Formation and retention of local melted films in AZ91 friction stir spot welds

The formation of local melted films during friction stir spot welding of as-cast AZ91D and thixomolded AZ91 material is investigated. The average temperatures close to the tip of the rotating pin vary from 438 to 454 °C during the dwell period in friction stir spot welding. These measured temperature values are higher than the melting temperature of α-Mg + Mg₁₇Al₁₂ eutectic (437 °C). It is suggested that the temperature in the stir zone during the dwell period is determined by the relative proportions of α-Mg and (α-Mg + Mg₁₇Al₁₂) eutectic material, which are incorporated during friction stir spot welding. Based on the stir zone temperature measurements and a detailed examination of material located at the root of the pin thread it is suggested that material is moved downwards via the pin thread and into the stir zone during the dwell period in friction stir spot welding. Evidence of local melted film formation is observed in the stir zone of AZ91 spot welds. It is suggested that melted films are retained since their dissolution rate is much slower in the high temperature stir zone than it is when melted films is formed in the stir zone during Al 7075-T6 friction stir spot welding. The spontaneous melting temperature, solute diffusion rate and the thermodynamic driving force for droplet dissolution are much higher during Al 7075-T6 friction stir spot welding.