Local residence time,residence revolution,and residence volume distributions in twin‐screw extruders

This work was aimed at studying the overall, partial, and local residence time distributions (RTD); overall, partial and local residence revolution distributions (RRD) and overall, partial and local residence volume distributions (RVD) in a co‐rotating twin screw extruder, on the one hand; and establishing the relationships among them, on the other hand. Emphasis was placed on the effects of the type and geometry of mixing elements (a gear block and various types of kneading elements differing in staggering angle) and process parameters on the RTD, RRD and RVD. The overall and partial RTD were directly measured in‐line during the extrusion process and the local ones were calculated by deconvolution based on a statistical theory. The local RTD allowed comparing the mixing performance of mixing elements. Also it was confirmed both experimentally and theoretically that specific throughput, defined as a ratio of throughput (Q) over screw speed (N), controlled all the above three types of residence distributions, be they local, partial or overall. The RRD and RVD do not provide more information on an extrusion process than the corresponding RTD. Rather they are different ways of representing the same phenomena. POLYM. ENG. SCI., 48:19–28, 2008. © 2007 Society of Plastics Engineers     

Synthesis and Characterizations of Triphenylamine End-Functionalized Polymers via Reversible Addition-Fragmentation Chain Transfer Polymerization

A novel reversible addition-fragmentation chain transfer (RAFT) reagent bearing triphenylamine (TPA) group, 4-diphenylamino-dithiobenzoic acid benzyl ester (DDABE), was designed and synthesized. It was used in the RAFT polymerizations of styrene (St) and methyl acrylate (MA) to prepare end-functionalized polymers. The results of the polymerization showed that the RAFT polymerizations could be well controlled using DDABE as the RAFT agent. Number-average molecular weight (M_n,GPC) increased linearly with monomer conversion, and molecular weight distributions were relatively narrow (PDI< 1.50). The results of chain-extension reaction, ¹H NMR spectra and UV/Vis spectra confirmed that most of the polymers chains were end-capped by the functional triphenylamine (TPA) groups. The effect of feed molar ratios of St/DDABE/AIBN on polymerization was investigated.     

Ring‐opening polymerization of D,L‐lactide by rare earth 2,6‐dimethylaryloxide

Ring‐opening polymerization of D,L ‐lactide (LA) has been successfully carried out by using rare earth 2,6‐dimethylaryloxide (Ln(ODMP)₃) as single component catalyst or initiator for the first time. The effects of different rare earth elements, solvents, monomers and catalyst concentration as well as polymerization temperature and time on the polymerization were investigated. The results show that La(ODMP)₃ exhibits higher activity to prepare poly(D,L ‐lactide) (PLA) with a viscosity molecular weight of 4.5 × 10⁴ g mol^?1 and the conversion of 97 % at 100 °C in 45 min. The catalytic activity of Ln(ODMP)₃ has following sequence: La > Nd > Sm > Gd > Er > Y. A kinetic study has indicated that the polymerization is first order with respect to both monomer and catalyst concentration. The apparent activation energy of the polymerization of LA with La(ODMP)₃ is 69.6 kJ mol^?1. The analyses of polymer ends indicate that the LA polymerization proceeds according to ‘coordination–insertion’ mechanism with selective cleavage of the acyl–oxygen bond of the monomer. Copyright © 2004 Society of Chemical Industry     

Controlled Synthesis of Ag2S,Ag2Se,and Ag Nanofibers by Using a General Sacrificial Template and Their Application in Electronic Device Fabrication

Nanofiber bundles of Ag₂S, Ag₂Se, and Ag have been successfully synthesized by making use of Ag₂C₂O₄ template nanofiber bundles, utilizing both anion‐exchange and redox reactions. The obtained bundles were polycrystalline nanofibers composed of nanoparticles in which the precursor morphology was well‐preserved, indicating that Ag₂C₂O₄ nanofiber bundles acted as a general sacrificial template for the synthesis of silver‐based semiconductor and metal nanofibers. Dispersing media and transforming reactants were found to be key factors influencing the chemical transformation in the system. In particular, separate single‐crystalline Ag nanofibers were obtained via a nontemplate route when ascorbic acid was used as a relatively weak reductant. An electrical transfer and switching device was built with the obtained Ag₂S and Ag nanofiber bundles, utilizing the unique ion‐conductor nature of Ag₂S and revealing their potential applications in electronics.     

Hydrothermal Reaction Mechanism and Pathway for the Formation of K2Ti6O13 Nanowires

Calculations and detailed first principle and thermodynamic analyses have been performed to understand the formation mechanism of K₂Ti₆O₁₃ nanowires (NWs) by a hydrothermal reaction between bulk Na₂Ti₃O₇ crystals and a KOH solution. It is found that direct ion exchange between K⁺ and Na⁺ plus H⁺ interactions with [TiO₆] octahedra in Na₂Ti₃O₇ promote the formation of an intermediate H₂K₂Ti₆O₁₄ phase. The large lattice mismatch between this intermediate phase and the bulk Na₂Ti₃O₇ structure, and the large energy reduction associated with the formation of this intermediate phase, drive the splitting of the bulk crystal into H₂K₂Ti₆O₁₄ NWs. However, these NWs are not stable because of large [TiO₆] octahedra distortion and are subject to a dehydration process, which results in uniform K₂Ti₆O₁₃ NWs with narrowly distributed diameters of around 10 nm.     

Structural and Superconducting Property Variations with Nominal Mg Non‐Stoichiometry in MgxB2 and Its Enhancement of Upper Critical Field

By applying a combination of characterisation tools, changes in structural and superconducting properties with nominal Mg non‐stoichiometry in Mg_xB₂ are found. The non‐stoichiometry produces enhanced in‐field critical current densities (J_c's) and upper critical field / irreversibility field (H_c2/H_irr(T)) values. Upper critical fields of ～ 21 T (4.2 K) were obtained in nominal Mg‐deficient samples compared to ～ 17 T (4.2 K) for near‐stoichiometric samples.     

Investigation on Single-Mode–Multimode– Single-Mode Fiber Structure

This paper presents an investigation on a single-mode-multimode-single-mode fiber structure. A one-way guided-mode propagation analysis for the circular symmetry waveguide is employed to model the light propagation and the approximated formulations are derived and evaluated concerning the accuracy. Phase conjunction of the multimode interference within the fiber structure is revealed. A simple way to predict and analyze the spectral response of the structure is presented through the space to wavelength mapping with the derived approximated formulations. The prediction of spectral response is verified numerically and experimentally.     

Effect of surfactants and liquid hydrocarbons on gas hydrate formation rate and storage capacity

Hydrate formation rate plays an important role in making hydrates for the storage and transport of natural gas. Micellar surfactant solutions were found to increase gas hydrate formation rate and storage capacity. With the presence of surfactant, hydrate could form quickly in a quiescent system and the energy costs of hydrate formation reduced. Surfactants (an anionic surfactant, a non‐ionic surfactant and their mixtures) and liquid hydrocarbons (cyclopentane and methylcyclohexane) were used to improve hydrate formation. The experiments of hydrate formation were carried out in the pressure range 3.69–6.82 MPa and the temperature range 274.05–277.55 K. The experimental pressures were kept constant during hydrate formation in each experimental run. The effect of anionic surfactant (sodium dodecyl sulphate (SDS)) on natural gas storage in hydrates is more pronounced compared to a non‐ionic surfactant (dodecyl polysaccharide glycoside (DPG)). The induction time of hydrate formation was reduced with the presence of cyclopentane (CP). Cyclopentane and methylcyclohexane (MCH) could increase hydrate formation rate, but reduced hydrate storage capacity The higher methylcyclohexane concentration, the lower the hydrate storage capacity. Copyright © 2003 John Wiley & Sons, Ltd.     

Average consensus in networks of dynamic agents with switching topologies and multiple time-varying delays

In this paper, we discuss average consensus problem in undirected networks of dynamic agents with fixed and switching topologies as well as multiple time-varying communication delays. By employing a linear matrix inequality method, we prove that all the nodes in the network achieve average consensus asymptotically for appropriate communication delays if the network topology is connected. Particularly, several feasible linear matrix inequalities are established to determine the maximal allowable upper bound of time-varying communication delays. Numerical examples are given to demonstrate the effectiveness and the sharpness of the theoretical results.     

Driving Mechanisms of Delamination Related Reliability Problems in Exposed Pad Packages

Exposed pad packages were introduced in the late 1980s and early 1990s because of their excellent thermal and electrical performance. Despite these advantages, the exposed pad packages experience a lot of thermo-hygro-mechanical related reliability problems during qualification and testing. Examples are die lift, which occurs predominantly after moisture sensitivity level conditions, and die-attach to leadframe delamination leading to downbond stitch breaks during temperature cycling. In this chapter, nonlinear finite element (FE) models using fracture mechanics based J-integral calculations are used to assess the reliability problems of the exposed pad package family. Using the parametric FE models any geometrical and material effects can be explored to their impact on the occurrence diepad delamination, and dielift. For instance the impact of diepad size is found to be of much less importance as the impact of die thickness is. Using the fracture mechanics approach, the starting location for the delamination from thermo-hygro-mechanical point of view is deducted. The results indicate that when diepad delamination is present, cracks are likely to grow beneath the die and dielift will occur. The interaction between dielift and other failure modes, such as lifted ball bonds, are not found to be very significant. The FE models are combined with simulation-based optimization methods to deduct design guidelines for optimal reliability of the exposed pad family.