High-performance MIM capacitor using ALD high-k HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectrics

For the first time, we successfully fabricated and demonstrated high performance metal-insulator-metal (MIM) capacitors with HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectric using atomic layer deposition (ALD) technique. Our data indicates that the laminate MIM capacitor can provide high capacitance density of 12.8 fF//spl mu/m/sup 2/ from 10 kHz up to 20 GHz, very low leakage current of 3.2 /spl times/ 10/sup -8/ A/cm/sup 2/ at 3.3 V, small linear voltage coefficient of capacitance of 240 ppm/V together with quadratic one of 1830 ppm/V/sup 2/, temperature coefficient of capacitance of 182 ppm//spl deg/C, and high breakdown field of /spl sim/6 MV/cm as well as promising reliability. As a result, the HfO/sub 2/-Al/sub 2/O/sub 3/ laminate is a very promising candidate for next generation MIM capacitor for radio frequency and mixed signal integrated circuit applications.     

Optimal Control of the Primary Drying Stage of Freeze Drying of Solutions in Vials Using Variational Calculus

The problem of operating freeze drying of pharmaceutical products in vials placed in trays of a freeze dryer to remove free water (in frozen state) at a minimum time was formulated as an optimal control problem. Two different types of freeze dryer designs were considered. In type I freeze dryer design, upper and lower plate temperatures were controlled together, while in type II freeze dryer design, upper and lower plate temperatures were controlled independently. The heat input to the material being dried and the drying chamber pressure were considered as control variables. Constraints were placed on the system state variables by the melting and scorch temperatures during primary drying stage. Necessary conditions of optimality for the primary drying stage of freeze drying process in vials are derived and presented. Furthermore, an approach for constructing the optimal control policies that would minimize the drying time for the primary drying stage was given. In order to analyze optimal control policy for the primary drying stage of the freeze-drying process in vials, a rigorous multi-dimensional unsteady state mathematical model was used. The theoretical approach presented in this work was applied in the freeze drying of skim milk. Significant reductions in the drying times of primary drying stage of freeze drying process in vials were obtained, as compared to the drying times obtained from conventional operational policies.     

Serially concatenated space-time codes with iterative decoding and performance limits of block-fading channels

This work considers space-time channel coding for systems with multiple-transmit and a single-receive antenna, over space uncorrelated block-fading (quasi-static) channels. Analysis of the outage probability over such channels reveals the existence of a threshold phenomenon. The outage probability can be made arbitrary small by increasing the number of transmit antennas, only if the E/sub b//N/sub 0/ is above a threshold which depends on the coding rate. Furthermore, it is shown that when the number of transmit antennas is increased, the /spl epsi/-capacity of a block-fading Rayleigh channel tends to the Shannon capacity of an additive white Gaussian noise channel. This paper also presents space-time codes constructed as a serial concatenation of component convolutional codes separated by an interleaver. These schemes provide full transmit diversity and are suitable for iterative decoding. The rate of these schemes is less than 1 bit/s/Hz, but can be made arbitrary close to 1 bit/s/Hz by the use of Wyner-Ash codes as outer components. Comparison of these schemes with structures from literature shows that performance gains can be obtained at the expense of a small decrease in rate. Computer simulation results over block-fading Rayleigh channels show that the frame-error rate of several of these schemes is within 2-3 dB from the theoretical outage probability.     

High-resolution photonics-based interference suppression filter with wide passband

A new topology for a photonic signal processor, which overcomes the basic recursive frequency response problem that limits the passband range, is presented. The structure is based on a new multiple-wavelength offset-cavity structure that is cascaded with a series of unbalanced delay line structures. This not only can synthesize a very narrow notch response with good shape factor but also permits a multifold extension of the free spectral range (FSR) and passband width. Results on the interference mitigation filter demonstrate a stopband of 1% of center frequency and a fourfold increase in the FSR and passband width, while also having a very small shape factor, in excellent agreement with predictions.     

Wavelength-tunable 40-GHz picosecond harmonically mode-locked fiber laser source

We demonstrate a novel 40-GHz mode-locked fiber laser that utilizes a single active device to provide both gain and mode-locking. The laser produces pulses as short as 2.2 ps, is tunable over a 27-nm band centered at 1553 nm, and exhibits long-term stability without cavity-length feedback control. The pulse train at 1556 nm was used in a 40-Gb/s transmission experiment over 45 km with a low 0.4-dB power penalty.     

Modification of ASM3 for the determination of biomass adsorption/storage capacity in bulking sludge control.

The selector activated sludge (SAS) systems are known to prevent excessive growth of filamentous microorganisms responsible for bulking sludge, but these systems were hardly ever modelled. This study aimed to develop a model capable of predicting rapid substrate removal in the SAS systems. For this purpose, the Activated Sludge Model No. 3 (ASM3) was extended with three processes (adsorption, direct growth on the adsorbed substrate under aerobic or anoxic conditions). The modified ASM3 was tested against the results of batch experiments with the biomass originating from two full-scale SAS systems in Germany. The endogenous biomass was mixed with various readily biodegradable substrates (acetate, peptone, glucose and wastewater) and the utilisation of substrate (expresses as COD) and oxygen uptake rates (OURs) were measured during the experiments. In general, model predictions fitted to the experimental data, but a considerable number of kinetic (5) and stoichiometric (2) parameters needed to be adjusted during model calibration. The simulation results revealed that storage was generally a dominating process compared to direct growth in terms of the adsorbed substrate utilisation. The contribution of storage ranged from 65-71% (Plant A) and 69-92% (Plant B).