Deactivation of copper-ion-exchanged hydrogen-mordenite-type zeolite catalyst by SO2 for no reduction by NH3

Deactivation of copper-ion-exchanged hydrogen-mordenite-type zeolite catalyst by SO₂ for NO reduction by NH₃ was examined in a fixed-bed flow reactor. The deactivation of the catalyst was strongly dependent on reaction temperature. At high reaction temperatures over 300°C, the catalyst did not lose its initial activity up to 50 h of operation, regardless of SO₂ feed concentration from 500 to 20,000 ppm. However, at low reaction temperatures near 250°C, apparent deactivation did occur. Changes in the physicochemical properties such as surface area and sulfur content of deactivated catalyst well correlated with catalyst activity, depending upon reaction temperatures. The deactivation was due to pore blocking and/or filling by deactivating agents, which plugged and/or filled the pores of catalyst. The deactivating agents deposited on the catalyst surface were presumed to be (NH₄)₂SO₄ and/or (NH₄)HSO₄ from the results of TGA and ion-chromatography measurement.     

Monolithic SiGe Up‐/Down‐Conversion Mixers with Active Baluns

The purpose of this paper is to describe the implementation of monolithically matching circuits, interface circuits, and RF core circuits to the same substrate. We designed and fabricated on‐chip 1 to 6 GHz up‐conversion and 1 to 8 GHz down‐conversion mixers using a 0.8 µm SiGe hetero‐junction bipolar transistor (HBT) process technology. To fabricate a SiGe HBT, we used a reduced pressure chemical vapor deposition (RPCVD) system to grow a base epitaxial layer, and we adopted local oxidation of silicon (LOCOS) isolation to separate the device terminals. An up‐conversion mixer was implemented on‐chip using an intermediate frequency (IF) matching circuit, local oscillator (LO)/radio frequency (RF) wideband matching circuits, LO/IF input balun circuits, and an RF output balun circuit. The measured results of the fabricated up‐conversion mixer show a positive power conversion gain from 1 to 6 GHz and a bandwidth of about 4.5 GHz. Also, the down‐conversion mixer was implemented on‐chip using LO/RF wideband matching circuits, LO/RF input balun circuits, and an IF output balun circuit. The measured results of the fabricated down‐conversion mixer show a positive power conversion gain from 1 to 8 GHz and a bandwidth of about 4.5 GHz.     

Effects of α‐form or β‐form nuclei on polymorphic crystalline morphology of poly(butylene adipate)

The effects of α‐form and β‐form nuclei on polymorphic morphology of poly(butylene adipate) (PBA) upon recrystallization from the molten state up to various T_max values were examined by differential scanning calorimetry (DSC), wide‐angle X‐ray diffraction (WAXD) and polarized light microscopy (PLM). In this study, PBA with complex melting and polymorphism behaviour was used as a model for examining different types and extents of residual nuclei. As the PBA initially containing the sole α‐crystal was brought to a molten state of various T_max, the extents of trace α‐form crystal nuclei varied and were dependent on T_max. Furthermore, it did not matter whether, initially, the PBA contained α‐ or β‐form crystals (or both) because only a single type of α‐nuclei could be left upon treatment to the molten liquid state at T_max. Therefore, only the α‐crystal in PBA had ‘memory capacity’ in the molten liquid state while the β‐crystal did not. This was so because the latter had been completely transformed into the solid state prior to being heated into a liquid. PBA crystallized before α‐nuclei could be packed into α‐crystal, regardless of the crystallization temperature (T_c). For recrystallization from molten PBA without any nuclei, the crystalline polymorphism was correspondingly influenced by T_c. Copyright © 2005 Society of Chemical Industry     

Parathion degradation and toxicity reduction in solar photocatalysis and photolysis.

The solar photocatalytic degradation of methyl parathion was investigated using a circulating TiO2/solar light reactor. Under solar photocatalysis condition, parathion was more effectively degraded than solar photolysis and TiO2-only conditions. With solar photocatalysis, 20 mg/L of parathion was completely degraded within 60 min with a TOC decrease of 63% after 150 min. The main ionic byproducts during photocatalysis recovered from parathion degradation were mainly as NO3-, NO2- and NH4+, 80% of the sulphur as SO4(2-), and 5% of phosphorus as PO4(3-). The organic intermediates 4-nitrophenol and methyl paraoxon were also identified, and these were further degraded in solar photocatalytic condition. Two different bioassays (Vibrio fischeri and Daphnia magna) were used to test the acute toxicity of solutions treated by solar photocatalysis and photolysis. The Microtox test using V. fischeri showed that the toxicity expressed as EC50 (%) value increased from 5.5% to >82% in solar photocatalysis, indicating that the treated solution is non-toxic, but only increased from 4.9 to 20.5% after 150 min in solar photolysis. The acute toxicity test using D. magna showed that EC50 (%) increased from 0.05 to 1.08% under solar photocatalysis, but only increased to 0.12% after 150 min with solar photolysis, indicating the solution is still toxic. The pattern of toxicity reduction parallels the decrease in TOC and the parathion concentrations.     

Double melting behavior of cyclic tris(ethylene terephthalate)

Summary Cyclic tris(ethylene terephthalate) (CTET) was separated from oligomeric extract of poly(ethylene terephthalate) by the conventional solvent separation method. The structure of CTET was characterized by differential scanning calorimetry, X-ray diffraction, and scanning electron microscopy. It is shown that the double melting behavior of meltcrystallized CTET is attributed to the morphological change created by heat-treatment. The effect of the morphological change on the crystal structure of CTET was also examined.     

Fabrication and performance of parallel-addressed InGaN micro-LED arrays

High-performance, two-dimensional arrays of parallel-addressed InGaN blue micro-light-emitting diodes (LEDs) with individual element diameters of 8, 12, and 20 /spl mu/m, respectively, and overall dimensions 490 /spl times/490 /spl mu/m, have been fabricated. In order to overcome the difficulty of interconnecting multiple device elements with sufficient step-height coverage for contact metallization, a novel scheme involving the etching of sloped-sidewalls has been developed. The devices have current-voltage (I-V) characteristics approaching those of broad-area reference LEDs fabricated from the same wafer, and give comparable (3-mW) light output in the forward direction to the reference LEDs, despite much lower active area. The external efficiencies of the micro-LED arrays improve as the dimensions of the individual elements are scaled down. This is attributed to scattering at the etched sidewalls of in-plane propagating photons into the forward direction.     

共面转换液晶显示器中获得对比度高于1:600的新技术

薄膜晶体管液晶电视(TFT-LCD TV)因为具有薄、轻、紧凑和可随意放置的特点，已经占据了大部分电视机市场。除了这些物理特性以外，最重要的特性是已具有了良好像质的对比度。为了将对比度提高到1：600以上，对偏振片膜、背光源板、滤色片树脂、电极锥角和摩擦条件等都进行了研究。优化的背光板组合，光滑的电极锥角和摩擦方法的控制是提高对比度的主要控制因素。应用新开发的滤色片树脂，对获得高对比度最为有效。     

A PIN diode controlled variable attenuator using a 0-dB branch-line coupler

We describe a simple PIN diode controlled variable attenuator that employs a 0-dB branch line directional coupler. The response of the attenuator was measured between 1.3 GHz and 2.6 GHz. At the center frequency, the attenuation monotonically varied from 0.7 dB to 23 dB with the control voltage, and the distributed branch-line coupler structure resulted in low input reflection. Our attenuator is easier to design, smaller in area than a double hybrid coupled attenuator, and has comparable or better reflection and attenuation performance characteristics.