Broad-band MMICs based on modified loss-compensation method using 0.35-/spl mu/m SiGe BiCMOS technology

Using the concept of loss compensation, novel broad-band monolithic microwave integrated circuits (MMICs), including an amplifier and an analog multiplier/mixer, with LC ladder matching networks in a commercial 0.35-mum SiGe BiCMOS technology are demonstrated for the first time. An HBT two-stage cascade single-stage distributed amplifier (2-CSSDA) using the modified loss-compensation technique is presented. It demonstrates a small-signal gain of better than 15 dB from dc to 28 GHz (gain-bandwidth product=157 GHz) with a low power consumption of 48 mW and a miniature chip size of 0.63 mm² including testing pads. The gain-bandwidth product of the modified loss-compensated CSSDA is improved approximately 68% compared with the conventional attenuation-compensation technique. The wide-band amplifier achieves a high gain-bandwidth product with the lowest power consumption and smallest chip size. The broad-band mixer designed using a Gilbert cell with the modified loss-compensation technique achieves a measured power conversion gain of 19 dB with a 3-dB bandwidth from 0.1 to 23 GHz, which is the highest gain-bandwidth product of operation among previously reported MMIC mixers. As an analog multiplier, the measured sensitivity is better than 3000 V/W from 0.1 to 25 GHz, and the measured low-frequency noise floor and corner frequency can be estimated to be 20 nV/sqrt(Hz) and 1.2 kHz, respectively. The mixer performance represents state-of-the-art result of the MMIC broad-band mixers using commercial silicon-based technologies     

Theoretical analysis of RAIM in the occurrence of simultaneous two-satellite faults

Most algorithms on receiver autonomous integrity monitoring (RAIM) are under the assumption of a single-satellite fault, because there is an extremely small probability that significant simultaneous multiple-satellite faults may occur. However, after the implementation of the Galileo system in a few years, there will be more satellites in view for the user to utilise together with GPS satellites, and a combination of them will bring better performance for RAIM. On the other hand, with the help of wide area augmentation system and the use of dual-frequency operation, pseudo-range errors will be reduced greatly. Thus, tighter alert limits are required for RAIM, and formerly `small' errors should not be neglected. All of those factors make it necessary to consider simultaneous multiple-satellite faults. A detailed theoretical analysis of RAIM under the condition of two-satellite faults for both vertical and horizontal directions is presented. The characteristic/max slopes for every pair of satellites are then deduced in order to calculate the tighter vertical/horizontal protection level for RAIM     

Preparation, sintering, and microstructures of strontium barium bismuth tantalate layered perovskite ceramics

The solid solutions of Ba-doped SrBi₂Ta₂O₉ layered perovskite ceramic powders have been successfully prepared via a two-step process using BiTaO₄ as a precursor. The lattice constants of the solid solutions monotonically increase with increasing barium-ion content. The sinterability of (Sr_1–xBa_x)Bi₂Ta₂O₉ powders is significantly improved by increasing the barium-ion content. When the specimens with high barium-ion contents are sintered at 1100°C, they thermally decompose to form rod-like grains and the matrix expands, leading to a lower density. The addition of barium ions to SrBi₂Ta₂O₉ also results in significant variation in the morphology of the sintered specimens and the occurrence of c-axis preferred orientation which is ascribed to the anisotropic growth of plate-like grains. The precise control of the barium-ion content as well as the sintering conditions is critical for obtaining densified barium-ion doped SrBi₂Ta₂O₉ ceramics with a pure, layered perovskite structure.     

Piezoresistive Behavior Study on Finger‐Sensing Silicone Rubber/Graphite Nanosheet Nanocomposites

A novel finger‐sensing nanocomposite with remarkable and reversible piezoresistivity is successfully fabricated by dispersing homogeneously conductive graphite nanosheets (GNs) in a silicone rubber (SR) matrix. Because of the high aspect ratio of the graphite nanosheets, the nanocomposite displays a very low percolation threshold. The SR/GN nanocomposite with a volume fraction of conductive nanosheets closest to that for the percolation threshold presents a sharp positive‐pressure coefficient effect of the resistivity under very low pressure, namely, in the finger‐pressure range (0.3–0.7 MPa), whereby the abrupt transition could be attributed to compressive‐stress‐induced deformation of the conducting network. The super‐sensitive piezoresistive behavior of the nanocomposite is accounted for by an extension of the tunneling conduction theory which provides a good approximation to the piezoresistive effect.     

Effects of flux enhancing polymer on the characteristics of sludge in membrane bioreactor process.

A newly developed membrane performance enhancer (MPE) was used to prevent membrane fouling in a membrane bioreactor (MBR) process. It transpired that 1,000 mg/l of MPE reduced polysaccharide levels from 41 mg/I to 21 mg/I on average under the experimental condition. Repeated experiments also confirmed that 50-1,000 mg/l of MPE could reduce membrane fouling significantly and increase the intervals between membrane cleanings. Depending on MPE dosages and experimental conditions, trans-membrane pressure (TMP) increase was suppressed for 20-30 days, while baseline TMP surged within a few days. In addition, MPE allowed MBR operation even at 50,000 mg/l of total solid and reduced permeate COD. However, no evidence of toxicity for sludge was found from respiratory works.     

Enhancing echo cancellation via estimation of delay

The advent of packetized audio transmission, such as voice over IP (VoIP), has resulted in challenging requirements for echo cancellation technology. One key aspect of this technology is the need to characterize, quickly and accurately, the echo paths in the transmission media. Echo paths consist of a constant time delay with no echo signal and active regions in which the echo signal is present. When an adaptive filter echo cancellation algorithm is used, its performance can be greatly increased, and its complexity can be reduced if it is only applied to the active regions. This requires an algorithm to estimate the constant delay and locate the active regions. Traditionally, delay estimation has been based on direct application of cross-correlation. This method has poor performance because the input signals are highly correlated and has a high implementation cost because many cross-correlation lags have to be computed for longer time delays. The delay estimation addressed in this paper has two major advantages over the traditional methods. The first is that it has improved performance because the input signals are processed to have less correlation. The second is that the implementation cost is significantly reduced because fewer cross-correlation lags are computed, and an efficient method to estimate lags is created.     

Reliability evaluation of class-E and class-a power amplifiers with nanoscaled CMOS technology

Circuit reliability of class-E and class-A power amplifiers is investigated based on a newly developed degradation subcircuit model. Measured degradation characteristics on the fabricated circuits agree well with the simulation predictions. Using this model, we have found that the class-E amplifier degrades faster than a class-A amplifier, due to a much higher stress level during switching. With a drastic decrease of PAE, a shorter lifetime is expected for a class-E amplifier.