Super tough double network hydrogels and their application as biomaterials

The double network (DN) technique, developed by authors’ group, provides an innovative and universal pass way to fabricate hydrogels with super high toughness comparable to rubbers. The excellent mechanical performances of DN hydrogels originate from the specific combination of two networks with contrasting structures. The first brittle network serves as sacrificial bonds, which breaks into small clusters to efficiently disperse the stress around the crack tip into the surrounding damage zone, while the second ductile polymer chains act as hidden length, which extends extensively to sustain large deformation. Based on the principle of DN hydrogel, the author’s group recently has developed several novel systems and techniques, which has greatly expanded the practical accessibility of DN technique for practical use. The DN principle and the DN gel have already attracted much attention in the soft matter community. Inspired by the DN principle, many research groups have also designed and developed some innovative hydrogels with large enhancement in their mechanical strength and toughness. Some tough hydrogels fabricated by the DN technique also exhibit good biocompatibility and low friction resistance with promising prospective in industrial and medicine fields, especially for load-bearing artificial soft tissues such as artificial cartilage. In this feature article, we address the major concept and toughening mechanism of DN gel, then we describe some recent novel hydrogel systems based on the DN concept, and finally the applicability of DN gel as soft biomaterials is discussed.     

Room temperature amorphous to nanocrystalline transformation in ultra-thin films under tensile stress: an in situ TEM study

The amorphous to crystalline phase transformation process is typically known to take place at very high temperatures and facilitated by very high compressive stresses. In this study, we demonstrate crystallization of amorphous ultra-thin platinum films at room temperature under tensile stresses. Using a micro-electro-mechanical device, we applied up to 3% uniaxial tensile strain in 3-5 nm thick focused ion beam deposited platinum films supported by another 3-5 nm thick amorphous carbon film. The experiments were performed in situ inside a transmission electron microscope to acquire the bright field and selected area diffraction patterns. The platinum films were observed to crystallize irreversibly from an amorphous phase to face-centered cubic nanocrystals with average grain size of about 10 nm. Measurement of crystal spacing from electron diffraction patterns confirms large tensile residual stress in the platinum specimens. We propose that addition of the externally applied stress provides the activation energy needed to nucleate crystallization, while subsequent grain growth takes place through enhanced atomic and vacancy diffusion as an energetically favorable route towards stress relaxation at the nanoscale.     

Indoor exposure to particulate matter and the incidence of acute lower respiratory infections among children: A birth cohort study in urban Bangladesh

Approximately half of all children under two years of age in Bangladesh suffer from an acute lower respiratory infection (ALRI) each year. Exposure to indoor biomass smoke has been consistently associated with an increased risk of ALRI in young children. Our aim was to estimate the effect of indoor exposure to particulate matter (PM_2.5) on the incidence of ALRI among children in a low‐income, urban community in Bangladesh. We followed 257 children through two years of age to determine their frequency of ALRI and measured the PM_2.5 concentrations in their sleeping space. Poisson regression was used to estimate the association between ALRI and the number of hours per day that PM_2.5 concentrations exceeded 100 μg/m³, adjusting for known confounders. Each hour that PM_2.5 concentrations exceeded 100 μg/m³ was associated with a 7% increase in incidence of ALRI among children aged 0–11 months (adjusted incidence rate ratio (IRR) 1.07, 95% CI 1.01–1.14), but not in children 12–23 months old (adjusted IRR 1.00, 95% CI 0.92–1.09). Results from this study suggest that reducing indoor PM_2.5 exposure could decrease the frequency of ALRI among infants, the children at highest risk of death from these infections.     

Wear failure of a leaded bronze bearing: Correlation between plant experience and laboratory wear test data

This paper describes an investigation on the failure of a large leaded bronze bearing that supports a nine-ton roller of a plastic calendering machine. At the end of the normal service life of a good bearing, which lasted for seven years, a new bearing was installed. However the new one failed catastrophically within a few days, generating a huge amount of metallic wear debris and causing pitting on the surface of the cast iron roller. Following the failure, samples were collected from both good and failed bearings. The samples were analyzed chemically and their microstructures examined. Both samples were subjected to accelerated wear tests in a laboratory type pin-on-disk apparatus. During the tests, the bearing materials acted as pins, which were pressed against a rotating cast iron disk. The wear behaviors of both bearing materials were studied using weight loss measurement. The worn surfaces of samples and the wear debris were examined by light optical microscope, scanning electron microscope, and energy-dispersive x-ray microanalyzer. It was found that the laboratory pin-on-disk wear data correlated well with the plant experience. It is suggested that the higher lead content (∼18%) of the good bearing compared with 7% lead of the failed bearing helped to establish a protective transfer layer on the worn surface. This transfer layer reduced metal-to-metal contact between the bearing and the roller and resulted in a lower wear rate. The lower lead content of the failed bearing does not allow the establishment of a well-protected transfer layer and leads to rapid wear.     

Physico-mechanical properties of chemically treated coir reinforced polypropylene composites

The physico-mechanical properties of coir reinforced polypropylene (PP) composites been investigated. In order to attain improved mechanical properties of the composites coir was chemically treated with o-hydroxybenzene diazonium salt. Both raw and treated coir samples were utilized for the fabrication of the composites. The mechanical properties of the composites prepared from chemically treated coir are found to be much better compared to those of untreated ones. Tensile strengths of the composites of both raw and chemically treated coir-PP composites showed a decreasing trend with increasing filler content. However, the values for the chemically treated coir-PP composites at all mixing ratios are found to be higher than that of neat PP. The surface morphologies of the fractured surfaces of the composites were recorded using scanning electron microscopy (SEM) to gain information about the fiber–matrix interfacial adhesion in the composites.     

Modeling the effect of statistical variations in length and diameter of randomly oriented CNTs on the properties of CNT reinforced nanocomposites

A nano-mechanical model has been developed to calculate the tensile modulus and the tensile strength of randomly oriented short carbon nanotubes (CNTs) reinforced nanocomposites, considering the statistical variations of diameter and length of the CNTs. According to this model, the entire composite is divided into several composite segments which contain CNTs of almost the same diameter and length. The tensile modulus and tensile strength of the composite are then calculated by the weighted sum of the corresponding modulus and strength of each composite segment. The existing micro-mechanical approach for modeling the short fiber composites is modified to account for the structure of the CNTs, to calculate the modulus and the strength of each segmented CNT reinforced composites. Multi-walled CNTs with and without inter-tube bridging have been considered. Statistical variations of the diameter and length of the CNTs are modeled by a normal distribution. Simulation results show that CNTs inter-tube bridging, length and diameter affect the nanocomposites modulus and strength. Simulation results have been compared with the available experimental results and the comparison concludes that the developed model can be effectively used to predict tensile modulus and tensile strength of CNTs reinforced composites.