Fracture Energies of Tape-Cast Silicon Nitride with β-Si3N4 Seed Addition

The fracture energies of the tape-cast silicon nitride with and without 3 wt% rod-like β-Si₃N₄ seed addition were investigated by a chevron-notched-beam technique. The material was doped with Lu₂O₃–SiO₂ as sintering additives for giving rigid grain boundaries and good heat resistance. The seeded and tape-cast silicon nitride has anisotropic microstructure, where the fibrous grains grown from seeds were preferentially aligned parallel to the casting direction. When a stress was applied parallel to the fibrous grain alignment direction, the strength measured at 1500°C was 738 MPa, which was almost the same as room temperature strength 739 MPa. The fracture energy of the tape-cast Si₃N₄ without seed addition was 109 and 454 J/m² at room temperature and 1500°C, respectively. On the contrary, the fracture energy of the seeded and tape-cast Si₃N₄ was 301 and 781 J/m² at room temperature and 1500°C, respectively, when a stress was applied parallel to the fibrous gain alignment. The large fracture energies were attributable primarily to the unidirectional alignment fibrous Si₃N₄ grains.     

Physical properties of silk fibers treated with ethylene glycol diglycidyl ether by the pad/batch method

This paper deals with the epoxide treatment of silk fabrics by the pad/batch method. The optimum reaction conditions, i.e., NaOH concentration, and reaction temperature were 2.5 g/L and 30°C, respectively. A weight gain of 8.5% was attained at a reaction time of 6 h. This value slightly increased to 10% after 24 h. The reactivity of tyrosine and basic amino acid residues was dependent on the reaction time and did not significantly differ from the results of epoxide-treated silk fiber by the conventional method in tetrachloroethylene. The moisture regain slightly decreased at 4% weight gain and then increased with the epoxide content, exceeding the value of the untreated control. The crease recovery of the epoxide-treated silk fabrics measured in the wet state was significantly improved, whereas that in the dry state was almost unchanged. The rate of photoyellowing of the epoxide-treated silk fabrics by the pad/batch method was reduced significantly compared with that of the untreated control. Among the mechanical properties, elongation at break and tensile modulus remained unchanged, whereas the tensile strength slightly increased following the epoxide reaction. The thermal properties were evaluated by DSC and TGA and on the basis of the dynamic viscoelastic measurements. The DSC curve of the epoxide-treated sample showed a slight increase of the decomposition temperature of silk fibroin. The rate of weight loss determined by TGA remained unchanged regardless of the chemical modification, whereas the peak of loss modulus became broader and shifted to lower temperature. The X-ray diffractograms showed that the crystalline structure of silk fibers was not affected by the reaction with epoxides. © 1993 John Wiley & Sons, Inc.     

The surface film formed on amorphous Pd-Ti-P alloy by anodic polarization in 2 m NaCl solution

X-ray photoelectron spectroscopy was used to investigate the effect of the composition and thickness of surface film on the electrocatalytic properties for chlorine gas evolution on amorphous Pd-Ti-P alloy in NaCl solution. The amount of charge for gas evolution exhibited a wavy change with an increase in polarization potential. The gas evolution became active with an increase in palladium content of the surface film and slowed down with increases of titanium and phosphorus contents of the film. However, despite the fact that the formation of surface film consisting mainly of titanium as a cation in the potential region higher than 1.6 V (sce), the catalytic activity for gas evolution increased, suggesting the change in the gas evolution mechanism in the higher potential region.     

Anodic characteristics of amorphorous palladium-base alloys in sodium chloride solutions

The anodic characteristics of a variety of amorphous palladium-base alloys were examined with a view to their use for the production of sodium hypochlorite by electrolysis of dilute sodium chloride solutions at ambient temperature. The corrosion resistance of palladium-metalloid alloys was obtained by alloying with platinum group metals and/or valve metals. Among these alloys, rhodium-containing alloys showed high electrocatalytic activities for chlorine evolution. Surface activation treatment was, however, necessary to obtain sufficiently high activities for chlorine evolution at low overpotentials. Surface-activated amorphous alloys possessed considerably higher current efficiency for chlorine evolution in comparison with currently used anodes.     

In Situ Synthesis and Microstructures of Tungsten Carbide-Nanoparticle-Reinforced Silicon Nitride-Matrix Composites

A W₂C-nanoparticle-reinforced Si₃N₄-matrix composite was fabricated by sintering porous Si₃N₄ that had been infiltrated with a tungsten solution. During the sintering procedure, nanometer-sized W₂C particles grew in situ from the reaction between the tungsten and carbon sources considered to originate mainly from residual binder. The W₂C particles resided in the grain-boundary junctions of the Si₃N₄, had an average diameter of ∼60 nm, and were polyhedral in shape. Because the residual carbon, which normally would obstruct sintering, reacted with the tungsten to form W₂C particles in the composite, the sinterability of the Si₃N₄ was improved, and a W₂C–Si₃N₄ composite with almost full density was obtained. The flexural strength of the W₂C–Si₃N₄ composite was 1212 MPa, ∼34% higher than that of standard sintered Si₃N₄.     

An X-ray photoelectron spectroscopic study of electrocatalytic activity of platinum group metals for chlorine evolution

A correlation of the catalytic activity for anodic chlorine evolution of platinum group metals to the nature of the surface film formed during chlorine evolution in a sodium chloride solution was studied by X-ray photoelectron spectroscopy. The change in the surface film with increasing potential was found on platinum, including an increase in the cationic valence. This seemed responsible for the decrease in the activity for chlorine evolution on platinum in the high potential region. Increasing potential did not result in the appreciable increase in the cationic valence in the surface film on the other platinum group metals. Replacement of hydroxyl ions in the surface film by chloride ions became easier in the order of rhodium, iridium and palladium, and the activity for anodic chlorine evolution increased in this order due possibly to an increase in the amount of chloride ions in the film which seemed to be one of the reactants in the rate determining electrochemical desorption of adsorbed chlorine atom. Chlorine molecules adsorbed on the surface film were also found. It was assumed that the activity for anodic chlorine evolution might be low when the metal surface was covered by a large amount of molecular chlorine which was the reaction product.     

Monodisperse nanoparticles of poly(ethylene glycol) macromers and N‐isopropyl acrylamide for biomedical applications

Poly(ethylene glycol)‐based nanoparticles have received significant attention in the field of biomedicine. When they are copolymerized with pH‐ or temperature‐sensitive comonomers, their small size allows them to respond very quickly to changes in the environment, including changes in the pH, ionic strength, and temperature. In addition, the high surface‐to‐volume ratio makes them highly functionalized. In this work, nanoparticles composed of temperature‐sensitive poly(N‐isopropylacrylamide), poly(ethylene glycol) 400 dimethacrylate, and poly(ethylene glycol) 1000 methacrylate were prepared by a thermally initiated, free‐radical dispersion polymerization method. The temperature‐responsive behavior of the hydrogel nanoparticles was characterized by the study of their particle size with photon correlation spectroscopy. The size of the nanoparticles varied from 200 to 1100 nm and was a strong function of the temperature of the system, from 5 to 40°C. The thermal, structural, and morphological characteristics were also investigated. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1678–1684, 2003     

Balanced corpus of contemporary written Japanese

The balanced corpus of contemporary written Japanese (BCCWJ) is Japan’s first 100 million words balanced corpus. It consists of three subcorpora (publication subcorpus, library subcorpus, and special-purpose subcorpus) and covers a wide range of text registers including books in general, magazines, newspapers, governmental white papers, best-selling books, an internet bulletin-board, a blog, school textbooks, minutes of the national diet, publicity newsletters of local governments, laws, and poetry verses. A random sampling technique is utilized whenever possible in order to maximize the representativeness of the corpus. The corpus is annotated in terms of dual POS analysis, document structure, and bibliographical information. The BCCWJ is currently accessible in three different ways including Chunagon a web-based interface to the dual POS analysis data. Lastly, results of some pilot evaluation of the corpus with respect to the textual diversity are reported. The analyses include POS distribution, word-class distribution, entropy of orthography, sentence length, and variation of the adjective predicate. High textual diversity is observed in all these analyses.     

A negative resist for KrF excimer laser lithography

The design and preparation of a series of negative resists for KrF excimer laser lithography are described. Each resist is composed of poly(hydroxystyrene) and an aromatic azide. The base resin shows high transmittance of 62%/μm at 248 nm, when p-ethylphenyl p-azidophenylsulfonate. 4-azido-4α-methoxy-chalcone, 1-(4 azidobenzylidene)-3-(α-hydroxy-4-azidobenzyl)-indene, 4,4α-diazido-3,3α-dimethoxybiphenyl, or 1-(4-azidostyryl)-5, 5-dimethyl-2-cyclohexen-1-one is employed as a sensitizer. These azides are obtained by red-shifting the absorption maxima to lower energy regions than the exposing wavelength of 248 nm. Transmittance of resists can be controlled from 10 to 30%. The resist is exposed with a KrF excimer laser stepper and developed in an alkaline solution. Sensitivities of about 15 mJ/cm² are observed. A good, subhalf-micron resist profile is achieved. The photochemical reaction mechanisms of poly(hydroxystyrene) and 4,4α-diazido-3,3α-dimethoxybiphenyl were studied at 248 nm and 313 nm exposure. Quantum yield for photodecomposition at 248 nm is seven times larger than that at 313 nm, but dissolution-inhibition effects are larger at 313 nm exposure. Consequently, the resist shows higher sensitivity at 313 nm than at 248 nm.     

Preparation of Aluminum Nitride Powder from Aluminum Polynuclear Complexes

AIN powder was synthesized from aluminum polynuclear complexes. Basic aluminum chloride and basic aluminum lactate were used as the aluminum polynuclear complexes. These starting materials and glucose were dissolved in water and mixed homogeneously. AIN powder was obtained by calcining after drying and precalcining at 800°C under nitrogen gas flow. Then excess carbon was removed by firing in air. Nitridation in the system was investigated and compared with that in the alumina–carbon black system. It was found that in our reaction system nitridation began and proceeded at lower calcination temperatures above 1200°C than in the alumina–carbon black system. Using aluminum polynuclear complexes, AIN was synthesized through the nitridation of γ-alumina and produced in a very fine and sharp particle size distribution.