Preparation and antibacterial activity of novel fluoroalkyl end-capped oligomers/silica nanocomposites-encapsulated low molecular biocides

Fluoroalkyl end-capped N-(1,1-dimethyl-3-oxobutyl)acrylamide oligomer [R_F-(DOBAA) _n -R_F] reacted with tetraethoxysilane (TEOS) and silica nanoparticles in the presence of low-molecular weight biocides such as hibitane, hinokitiol, and hinokioil under alkaline conditions to afford R_F-(DOBAA) _n -R_F/silica nanocomposites-encapsulated these biocides in excellent to moderate isolated yields. Fluoroalkyl end-capped N,N-dimethylacrylamide oligomer [R_F-(DMAA) _n -R_F] and acrylic acid oligomer [R_F-(ACA) _n -R_F]/silica nanocomposites-encapsulated hibitane were obtained under similar conditions. Dynamic light scattering measurements showed that the size of these fluorinated nanocomposites-encapsulated biocides thus obtained is nanometer size-controlled. Additionally, these fluorinated nanocomposites were shown to have a good dispersibility and stability in methanol and water. Of particular interest, these fluorinated nanocomposites-encapsulated biocides were found to have a good antibacterial activity against Staphylococcus aureus, and these nanocomposites were applied to the surface modification of traditional organic polymers such as poly(methyl methacrylate).     

Design and fabrication of RESURF MOSFETs on 4H-SiC(0001), (112~0), and 6H-SiC(0001)

Design and fabrication of lateral SiC reduced surface field (RESURF) MOSFETs have been investigated. The doping concentration (dose) of the RESURF and lightly doped drain regions has been optimized to reduce the electric field crowding at the drain edge or in the gate oxide by using device simulation. The optimum oxidation condition depends on the polytype: N/sub 2/O oxidation at 1300/spl deg/C seems to be suitable for 4H-SiC, and dry O/sub 2/ oxidation at 1250/spl deg/C for 6H-SiC. The average inversion-channel mobility is 22, 78, and 68 cm/sup 2//Vs for 4H-SiC(0001), (112~0), and 6H-SiC(0001) MOSFETs, respectively. RESURF MOSFETs have been fabricated on 10-/spl mu/m-thick p-type 4H-SiC(0001), (112~0), and 6H-SiC(0001) epilayers with an acceptor concentration of 1/spl times/10/sup 16/ cm/sup -3/. A 6H-SiC(0001) RESURF MOSFET with a 3-/spl mu/m channel length exhibits a high breakdown voltage of 1620 V and an on-resistance of 234 m/spl Omega//spl middot/cm/sup 2/. A 4H-SiC(112~0) RESURF MOSFET shows the characteristics of 1230 V-138 m/spl Omega//spl middot/cm/sup 2/.     

An analysis of shielding against DC magnetic fields generated by electric railways. Evaluation of effective permeability of fine structure

This paper describes an effective analysis of magnetic shielding based on homogenization. The analyses become time‐consuming if the problems include the magnetic substances having fine structure. The homogenization of the structure makes it possible to analyze effectively the magnetic fields. The authors introduce a method to estimate the effective permeability of the homogenized substance. This method can be applied to any periodic structure made of magnetic substance. The magnetic shielding effects by the structures against direct‐current (DC) fields generated by electric railways are analyzed by using the present method. As a result, it is found that the overhead way and the protective fence near the railway work as a magnetic shield, whose effects can be improved by appropriate arrangement of those constructions. © 2007 Wiley Periodicals, Inc. Electr Eng Jpn, 160(4): 7–15, 2007; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20310     

Prostaglandin E receptor subtypes in mouse osteoblastic cell line

PGE2 is one of the key molecules in the osteoblast. It is the major prostanoid in the bone, and its production is under the control of both systemic and local factors. PGE2 has been reported to have multiple actions in the osteoblast, such as growth promotion and cell differentiation. To better understand the action of PGE2 in the osteoblast, we determined the PGE receptor subtypes in MC3T3-E1, an osteoblastic cell line derived from the normal mouse calvaria. Northern blot analysis revealed that EP1 and EP4 subtypes are expressed in MC3T3-E1. In contrast, EP3 subtype was not detected by either Northern blot analysis or RT-PCR. The contribution of each subtype was evaluated by studying the effects of subtype-specific analogs on osteoblastic function at confluency and 5 days after confluency. An EP1 agonist, 17-phenyl-omega-trinor PGE2, increased DNA synthesis and decreased alkaline phosphatase activity. 11-Deoxy-PGE1, and EP2 and EP4 agonist, decreased DNA synthesis and increased alkaline phosphatase activity at both stages. Butaprost, an EP2-selective agonist, showed effects similar to those of 11-deoxy-PGE1 only at confluency. Another and more differentiated osteoblastic marker, osteocalcin production, was detectable and was stimulated by 11-deoxy-PGE1 only 5 days after confluency. The exposure of these cells to EP1 agonist changed the cell shape to a more fibroblastic appearance. These results indicate that EP1, EP4, and probably EP2 are present in MC3T3-E1 cells; EP1 promotes cell growth, and EP2 and EP4 mediate differentiation of the osteoblast. Furthermore, the decreased response to EP2-specific agonist 5 days after confluency suggests that the expression of PGE receptor subtype is dependent on the stage of osteoblastic differentiation. This is the first report to determine PGE receptor subtypes in the bone.     

Impulse breakdown voltages of triggered multistage vacuum gap

Several sealed-off triggered vacuum gaps are connected in series to improve hold-off voltage. The characteristics of impulse breakdown voltage of these series-connected gaps are investigated experimentally. The sum hold-off voltage of series-connected gaps decreases to a unit hold-off voltage when the maximum value of voltage division ratio across the gaps increases to unity. Self-breakdown probability of the series-connected gaps is always higher than that of a single gap under the same conditions. Hence, stage efficiency of the multistage gap decreases with increasing number of stages. Its value is 90 percent with 2-stage gap and 75 percent with 5-stage gap, respectively, under the same voltage division ratio and the same gap length (2.0 mm) in each stage. Triggered breakdown voltage of 2- or 3- stage gap is several hundred volts when all gaps are triggered simultaneously at the peak of the main impulse wave and a working voltage range is nearly 100 percent in this case. The working voltage range decreases with number of stages. Its value is 45 percent with 3-stage gap and 15 percent with 5-stage gap, respectively, when one triggered gap is fired for switching.     

Resistive superconducting transition of κ-type BEDT-TTF organic superconductors in a magnetic field

The superconducting transition of the organic compoundsκ-(BEDT-TTF)₂ X is studied by resistive measurement in a magnetic field up to 10 T applied normal to the conducting plane. For the salts withX=Cu[N(CN)₂]Br andX=CuCN[N(CN)₂] the transition shows fanshaped broadening caused by superconductivity fluctuation. For theX=Cu(NCS)₂ salt the resistivity shows a peak in the transition region in a magnetic field below 4 T.This phenomenon is suppressed in defect-reduced samples for intralayer conduction. We discuss this peak in relation to the thermal fluctuation on the Josephson junction structures in this salt.     

Stabilization of bioethanol recovery with silicone rubber‐coated ethanol‐permselective silicalite membranes by controlling the pH of acidic feed solution

In order to produce highly concentrated bioethanol by pervaporation using an ethanol‐permselective silicalite membrane, techniques to suppress adsorption of succinic acid, which is a chief by‐product of ethanol fermentation and causes the deterioration in pervaporation performance, onto the silicalite crystals was investigated. The amount adsorbed increased as the pH of the aqueous succinic acid solution decreased. The pervaporation performance also decreased with decreasing pH when the ternary mixtures of ethanol/water/succinic acid were separated. Using silicalite membranes individually coated with two types of silicone rubber, pervaporation performance was significantly improved in the pH range of 5 to 7, when compared with that of non‐coated silicalite membranes in ternary mixtures of ethanol/water/succinic acid. Moreover, when using a silicalite membrane double‐coated with the two types of silicone rubber, pervaporation performance was stabilized at lower pH values. In the separation of bioethanol by pervaporation using the double‐coated silicalite membrane, removal of accumulated substances having an ultraviolet absorption maximum at approximately 260 nm from the fermentation broth proved to be vital for efficient pervaporation. Copyright © 2005 Society of Chemical Industry     

Optimal production-inventory policy for make-to-order versus make-to-stock based on the M/Er/1 queuing model

This paper analyzes a multi-product production / inventory system where demands for each item arrive according to a Poisson process and the production time for each product has an Erlang distribution. The paper proposes an optimality condition that specifies whether each product should be produced make-to-stock or make-to-order. In the event a product should be produced make-to-stock, an approach for computing the optimal base-stock level is proposed. Numerical examples are given for illustrative purpose.     

Color registration error reduction method compensating the influence of belt thickness variation in electrophotographic process

This paper proposes a new belt drive control method for reducing a belt velocity-fluctuation that is caused by a belt thickness-variation in the circumferential direction. A belt driving system performs feedback control with a rotary encoder-output mounted on a driven roller. This proposed method correct the reference value of the feedback control for the purpose of the belt velocity regulation. The correction includes two steps. The first step acquires the encoder-output of the driven roller and calculates the rotational angular velocity-fluctuation with one cycle of the belt rotation. The second step converts from the velocity-fluctuation to the correction value of the feedback reference. The correction value cancels a detection error of the driven roller caused by the belt thickness-variation. After these steps, the belt driving system controls the belt velocity as compensating the belt velocity-fluctuation. Experimental result showed the significant fluctuation reduction on a typical tandem-engine printer.     

Survey of switching techniques in high-speed networks and their performance

One of the most promising approaches for high speed networks for integrated service applications is fast packet switching, or ATM (asynchronous transfer mode). ATM can be characterized by very high speed transmission links and simple, hard-wired protocols within a network. To match the transmission speed of the network links, and to minimize the overhead due to the processing of network protocols, the switching of cells is done in hardware switching fabrics in ATM networks. A number of designs have been proposed for implementing ATM switches. Although many differences exist among the proposals, the vast majority of them are based on self-routeing multistage interconnection networks. This is because of the desirable features of multi-stage interconnection networks such as self-routeing capability and suitability for VLSI implementation. Existing ATM switch architectures can be classified into two major classes: blocking switches, where blockings of cells may occur within a switch when more than one cell contends for the same internal link, and non-blocking switches, where no internal blocking occurs. A large number of techniques have also been proposed to improve the performance of blocking and non-blocking switches. In this paper, we present an extensive survey of the existing proposals for ATM switch architectures, focusing on their performance issues.