High-strength–high-modulus polyimide fibers II. Spinning and properties of fibers

The polyimides based on 3,3′,4,4′-biphenyltetracarboxylic dianhydride (BPDA) described in Part I of this series were dissolved in p-chlorophenol and spun into fibers using a coagulating bath of ethanol. The fibers as spun had in general low tenacities and low moduli, but a heat treatment at 300–500°C under tension produced a remarkable increase in strength and modulus, and fibers with a tensile strength of 26 g/den (3.1 GPa) and an initial modulus higher than 1,000 g/den (120 GPa) could be obtained. Thus, the annealed fibers of polyimides are comparable to aramid fibers in mechanical properties. To heating in air and in the saturated steam, the polyimide fibers showed higher resistance than the aramid fibers. The polyimide fibers surpassed the aramid fibers in resistance to acid treatment and ultraviolet (UV) irradiation, but were inferior in resistance to alkali treatment. The annealed fibers of polyimides displayed distinct X-ray diffraction patterns. The chain repeat distance of 20.5 Å determined on the fibers of polyimide prepared from BPDA and o-tolidine, and 20.6 Å determined on the fibers of polyimide derived from BPDA and 3,4′-diaminodiphenyl ether are reasonable when the dimensions of monomeric units and the shapes of the molecular chains are considered. The X-ray reflections of both polyimide fibers were indexed satisfactorily on the basis of postulated unit cells.     

Aggregation arrestant pheromone of the German cockroach,Blattella germanica (L.) (Dictyoptera: Blattellidae): Isolation and structure elucidation of blattellastanoside-A and -B

The aggregation pheromone of the German cockroach,Blattella germanica, consists of attractant and arrestant, which can be detected by olfactometer and choice-chamber assay, respectively. Both were extracted from the frass-contaminated filter paper being used as a shelter. They were separated by solvent partition withn-butanol and water. The arrestant from then-butanol phase was purified by open column chromatography and then successive HPLC isolated two major arrestant components. Spectral evidence from SI-MS, HR-EI-MS, and NMR experiments with pulse techniques provided possible structures as 1-(6-chloro-4,5-epoxy-5-stigmast-3-yl)--d-glucopyranoside and 1-(6-chloro-5-hydroxy-5-stigmast-3-yl)--d-glu-copyranoside, denoted as blattellastanoside-A and blattellastanoside-B, respectively. They represented arrestant activity as median effective doses (ED₅₀) at 0.044 (A) and 3.2 (B) nmol on 1.0 cm² of Whatman No. 1 filter paper.     

One-step formation of ethyl methyl ketone from 1-butene and water on ultrastable Y-type zeolite catalyst

Proton exchanged ultrastable Y-type zeolite with silica/alumina = 40 showed a pronounced catalytic activity for the formation of ethyl methyl ketone directly from 1-butene and water. The formation rate of ethyl methyl ketone was much higher than those on MoO₃-based catalysts in the oxidation of 1-butene by oxygen. It was suggested that the basic site necessary for the formation of ethyl ketone directly from 1-butene and water would be the pentacoordinated Al.     

Depolymerization of poly(fluoroalkyl methacrylate-co-methyl methacrylate) as studied with thermogravimetry

Thermal behaviors of a few kinds of poly(fluoroalkyl methacrylate-co-methyl methacrylate) prepared by γ-ray copolymerization were investigated by using thermogravimetric measurements together with the intermittent analysis of the gaseous products. The thermal degradation of copolymers composed of one of fluoroalkyl methacrylates of the following structures: CH₂?C(CH₃)COOCH₂(CF₂CF₂)_nH, where n = 1,2, and 3, and methyl methacrylate proceeded according to the depolymerization mechanism reproducing the pristine component comonomers exclusively, but their thermograms in inert atmosphere showed the feature of a two-step reaction. In air, however, thermograms of copolymers did not show such a stepwise decrease in weight with the elevating temperature, and temperatures at which depolymerization was introduced shifted to a much higher region. The overall aspects of depolymerization of copolymers seemed to be much similar to that of fluoroalkyl methacrylate homopolymer previously reported, and the retardation of depolymerization by air was considered to be due mainly to the stabilization of once-formed polymer radicals by oxygen.     

Hydrophobic effects on protein/nucleic acid interaction: enhancement of substrate binding by mutating tyrosine 45 to tryptophan in ribonuclease Tl

Hydrophobic effects on binding of ribonuclease Tl to guaninebases of several ribonucleotides have been proved by mutatinga hydrophobic residue at the recognition site and by measuringthe effect on binding. Mutation of a hydrophobic surface residueto a more hydrophobic residue (Tyr45 – Trp) enhances thebinding to ribonucleotides, including mononucleotide inhibitorand product, and a synthetic substrate-analog trinudeotide aswell as the binding to dinucleotide substrates and RNA. Enhancementson binding to non-substrate ribonucleotides by the mutationhave been observed with free energy changes ranging from –2.2 to – 3 .9 kJ/mol. These changes are in good agreementwith that of substrate binding, –2.3 kJ/mol, which iscalculated from Michaelis constants obtained from kinetic studies.It is shown, by comparing the observed and calculated changesin binding free energy with differences in the observed transferfree energy changes of the amino acid side chains from organicsolvents to water, that the enhancement observed on guaninebinding comes from the difference in the hydrophobic effectsof the side chains of tyrosine and tryptophan. Furthermore,a linear relationship between nucleolytic activities and hydrophobicityof the residues (Ala, Phe, Tyr, Trp) at position 45 is observed.The mutation could not change substantially the base specificityof RNase Tl, which exhibits a prime requirement for guaninebases of substrates.     

One-Step Synthesis of Luminescent Nanoparticles of Complex Oxide, Strontium Aluminate

An organic aqueous solution of metal acetylacetonate precursors was subjected to spray pyrolysis in order to fabricate SrAl₂O₄:Eu (SAO) nanoparticles. Non-agglomerated luminescent SAO nanoparticles, having a spherical shape with a size of 10–30 nm, were achieved in a single step, while only submicrometer-sized SAO particles were obtained from the conventional ultrasonic pyrolysis of the metal nitrates. Without any post-annealing process, the as-prepared SAO nanoparticles were observed to exhibit a strong photoluminescence, which is comparable with that of the submicrometer-sized SAO particles. A mechanism for the formation of the nanoparticles is also discussed.     

Formation of Bromate Ion Through a Radical Pathway in a Continuous Flow Reactor

The contribution of ozone and hydroxyl radical to the formation of bromate ion was investigated in a continuous flow reactor. Experiments were conducted under a wide range of ozone dose (0.7 ～ 3.8 mgL), pH (6.5 ～ 8.5), and t-butanol concentration (0 ～ 0.5 mM). The formation of bromate ion was found to depend on radical reaction pathway, because the amount of bromate ion formed increased with pH and decreased with t-butanol, a radical scavenger, even when dissolved ozone concentrations were almost the same. In fact, the amount of bromate ion formed was reduced by 90% in the presence of t-butanol. Furthermore, the formation of bromate ion occurred even when dissolved ozone was not significantly detected in the presence of organic matter (TOC of 1 mgCL). The second-order reaction rate constant of hydroxyl radical with bromide ion, k _HO,Br^? of 1.7 × 10⁹ (M^?1s^?1), was obtained on the assumption that the reactions of bromide ion and t-butanol with hydroxyl radical were competitive with each other in the presence of t-butanol and that the formation of bromate ion depended on the reaction of bromide ion with hydroxyl radical. Therefore, it is concluded that the reaction of bromide ion with hydroxyl radical dominated in the overall reaction from bromide ion to bromate ion in the continuous flow reactor.     

ARCOR,a new photolithography technique with antireflective coating on resist

The multiple interference effect is one of the major causes of the fluctuation in critical dimension control (CD) and in mark detection for alignment. Suppressing this effect is critical for future photolithography. We propose a new photolithography technique called anti reflective coating on resist (ARCOR), which improves linewidth accuracy and overlay accuracy by suppressing multiple interference. ARCOR consists of relatively simple processes: A clear antireflective film is spun onto the resist prior to the mark detecting for alignment and exposure. The film is subsequently removed and the resist developed in the conventional way. ARCOR differs from ARC, which suppresses the reflection at the resist/substrate interface. ARCOR suppresses the reflection at the air/resist interface. ARCOR allows mark detection and exposure without light intensity-loss and multiple interference. The experiments mainly examine polysiloxane and perfluoroalkylpolyether as ARCOR materials. It is shown that linewidth accuracy can be improved from 0.3 to 0.03 μm. The signal-to-noise ratio of the alignment signal is drastically improved, and the overlay error is about half that of the conventional method. ARCOR is also effective for directly measuring the reflectivity at the resist/substrate interface, which is a key parameter of the multiple interference effect and the halation. Using ARCOR and a thin resist film, the measured ratio of reflected light to incident light indicates the reflectivity at the resist/substrate interface. Because, the probe light does not reflect off the resist surface and the intensity-loss at the resist surface is suppressed. With perfluoroalkylpolyether film, the measurement error is ～ 1.5%.     

水性氯化物介质中对甲基苯烷基硫醚萃取钯的研究

p-Methylphenylalkylsulfide of various alkyl chain length as extractant were synthesized and the extraction of palladium was examined in terms of equilibrium and kinetics. Distribution ratio of Pd was independent of alkyl chain length. For aqueous chloride media, there was a significant difference in distribution ratios for the solution of NaC1 and HC1. The results of loading test and the slope analysis suggest that the extractant and Pd (Ⅱ) form 2:1 complex. Furthermore, the extraction rate based on the volume of aqueous phase was obtained in a stirred vessel, and the rate equation was presented. Unfortunately, it was difficult to construct surfactant liquid membrane system by use of the present extractant.     

Reactive blending of polyamide with polyethylene: pull-out of in situ-formed graft copolymers and its application for high-temperature materials

Reactive blending of polyamide 6 (PA) with polyethylene (PE) having reactive sites, maleic anhydride (MAH content=0.1 wt%),and glycidyl methacrylate (GMA content=3-12 wt%), was carried out at 70/30 and 65/35 (PA/PE) blend ratios. Blend morphology evolved by reactive blending was analyzed by light scattering and transmission electron microscopy. The blends were then irradiated by electron beam. The degree of crosslinking was estimated by measuring the dynamic storage modulus at a temperature above melting point of PA. It was found that surface-to-surface interparticle distance τ was significantly reduced by the micelle formation via pull-out of in situ-formed graft copolymers. The blend with shorter τ was crosslinked by electron-beam irradiation at the lower dose level. A blend having the minimum τ (∼0.2 μm) was nicely crosslinked at a low dose level same as for PE, and even for the PA matrix system.