Mutational analysis of structure--activity relationships in human tumor necrosis factor-alpha

To determine the region of human tumor necrosis factor-alpha(TNF-), essential for cytotoxic activity against mouse L-M cells,single amino-acid-substituted TNF- mutant proteins (muteins)were produced in Escherichia coli by protein engineering techniques.An expression plasmid for TNF- was mutagenized by passage throughan E.coli mutD5 mutator strain and by oligonucleotide-directedmutagenesis. Approximately 100 single amino-acid-substitutedTNF- muteins were produced and assayed for cytotoxic activity.The cytotoxic activities of purified TNF- muteins, e.g. TNF-31T,-32Y, -82D, -85H, -115L, -141Y, -144K and -146E, were < 1%of that of parent TNF-. These results indicate that the integrityof at least four distinct regions of the TNF- molecule is requiredfor full biological activity. These regions are designated asfollows: region I, from position 30 to 32; region II, from position82 to 89; region III, from position 115 to 117; region FV, fromposition 141 to 146. In addition, TNF-141Y could not completelycompete with parent TNF- for binding to the receptor. This demonstratesthat region IV, and at least aspartk acid at position 141, mustbe involved in the TNF receptor binding site.     

Temperature influence on performance degradation of hydrogenated amorphous silicon solar cells irradiated with protons

This paper reports temperature influence on radiation degradation of hydrogenated amorphous silicon (a‐Si : H) solar cells. Degradation behaviors of a‐Si : H solar cells irradiated with protons at 331 K are compared with that at 298 K (room temperature). Variations with time in the post‐irradiation electrical properties are also investigated. It is found that the radiation degradation of the electrical properties at 331 K is significantly smaller than that at room temperature. Also, all the electrical properties (short‐circuit current, open‐circuit voltage, output maximum, and fill factor) recover with time after irradiation even at room temperature. The characteristic time of thermal annealing of short‐circuit current is larger as the temperature is higher. These results indicate that temperature during irradiation and elapsed time from irradiation to measurement is an important parameter for radiation degradation of a‐Si : H solar cells. Therefore, these parameters should be controlled in conducting the ground radiation tests. Copyright © 2012 John Wiley & Sons, Ltd.     

An efficient 0.04-nm apodized fiber Bragg grating and its application to narrow-band spectral filtering

A narrow-band apodized fiber Bragg grating was fabricated with a phase mask method that incorporated a fluorescence monitoring technique. The grating length was 100 mm and the 3-dB reduced bandwidth was as small as 0.04 nm. The 20-dB reduced bandwidth was 0.1 nm at a center wavelength of 1554 mm. A single longitudinal oscillation mode of a 10-GHz pulse train from a mode-locked fiber laser was successfully extracted using the grating.     

Development of a 385–500 GHz Sideband-Separating Balanced SIS Mixer

A submillimeter (385–500 GHz) low-noise sideband-separating balanced SIS (Superconductor Insulator Superconductor) mixer (Balanced 2SB mixer) with high IRR (Image Rejection Ratio) has been successfully developed, whose SSB (Single SideBand) noise temperature is ～ 200 K (10hf/k) with an image rejection ratio of ≥?～10 dB. Balanced mixers have become a promising technology which would break through the limitation especially in terahertz receivers and heterodyne arrays. However, though there are examples in microwave with relatively worse noise performance, submillimeter and terahertz balanced mixers have rarely been developed in spite of their astronomical importance. The developed balanced 2SB mixer is not only the first one demonstrated at submillimeter frequency range, but also has very low noise, high IRR, wide detectable frequencies (385–500 GHz), and a flat IF output spectrum. The balanced 2SB mixer is composed of three RF hybrids, four DSB (Double SideBand) mixers, two 180° IF hybrids, and an IF quadrature hybrid. Several important performance indicators such as noise temperature, IRR, required LO (Local Oscillator) power, and IF spectra were measured. The measured LO power required for the balanced 2SB mixer was typically ~ 14 dB less than that of the single-ended mixers.     

Influence of Element Substitution on Corrosion Behavior of Bi<Subscript>2</Subscript>Te<Subscript>3</Subscript>-Based Compounds

Atmospheric water may condense on the surface of Bi₂Te₃-based compounds constituting the Peltier module, depending on the operating environment used. In the stage of disposal, Bi₂Te₃-based compounds may come into contact with water in waste disposal sites. There are very few publications about the influence of condensed water on Peltier modules. Bi₂Te₃-Sb₂Te₃ or Bi₂Te₃-Bi₂Se₃ pseudo binary system compounds are used as p-type material or n-type material, respectively. The lattice distortion will be induced in the crystal of Bi₂Te₃-based compounds by element substitution due to the reduction in their thermal conductivity. However, the influence of element substitution on the corrosion behavior of Bi₂Te₃-based compounds remains unclear. In this study, the influence of element substitution on the corrosion behavior of Bi₂Te₃-based compounds with practical compositions has been investigated. Bi_0.5Sb_1.5Te₃ or Bi₂Te_2.85Se_0.15 was prepared by the vertical Bridgman method. The electrochemical properties at room temperature were evaluated by cyclic voltammetry in a standard three-electrode cell. The working electrolyte was a naturally aerated 0.6 or 3.0 mass% NaCl solution. From the tendency for corrosion potential for all the samples, the corrosion sensitivity of ternary compounds was slightly higher than that of binary compounds. From the trend of current density, it was found that Bi_0.5Sb_1.5Te₃ had a corrosion resistance intermediate between Bi₂Te₃ and Sb₂Te₃. On the other hand, corrosion resistance was affected despite a small amount of Se substitution, and the corrosion resistance of Bi₂Te_2.85Se_0.15 was close to or lower than that of Bi₂Se₃. From the observation results of the corrosion products, the trends of morphology and composition of corrosion products for Bi_0.5Sb_1.5Te₃ or Bi₂Te_2.85Se_0.15 were consistent with those of Sb₂Te₃ or Bi₂Se₃, respectively. From the results of x-ray photoelectron spectroscopy for the electrolyte after testing, the possibility that a corrosion product diffuses to the environment including the salt was suggested in Bi_0.5Sb_1.5Te₃. However, the amount of dissolved corrosion product was very low, and the chemical stability of the corrosion product was not changed or improved by element substitution.     

Dynamic Base Station Selection for Personal Communication Systems with Distributed Control Schemes

Distributed control schemes allow base stations in personal communication systems to be placed at locations corresponding to high expected traffic. This flexible base station placement creates significant overlapping coverage areas that can be utilized to improve system performance [1]. A new technique for dynamic base station selection in systems with overlapping cells is considered and its effect on traffic performance is characterized. The technique realizes robust performance for personal communication systems in fluctuating and heavily tapered traffic. A mathematical analysis based on a state transition model is used to evaluate performance of a system that employs the proposed technique. The results indicate that improved blocking probability and carried traffic performance are obtainable. Computer simulations were undertaken confirm the analytical results.     

Design and Analysis of Vertical Split Ring Resonator and Its Application to Unbalanced–Balanced Filter

We present a design method and analysis for a vertical split ring resonator (SRR). Furthermore, we propose an unbalanced–balanced filter using vertical SRRs. First, we explain vertical SRR with a stepped impedance resonator (SIR) using virtual ground. The resonance frequency is theoretically derived based on asymmetric coupled transmission lines. The resonance frequencies of vertical SRRs, calculated by our derived equation, are in good agreement with those of 3-D simulations and measurements. Next, this resonator is applied to an unbalanced–balanced filter based on low-temperature co-fired ceramic (LTCC). The attenuation poles of this filter are controlled by coupling between high-impedance lines similar to a two-pole filter with a SIR. The dimensions of the measured filter implemented with LTCC are 2.0 $times$ 1.2 $times$ 0.60 mm. The insertion loss is 2.80 dB in a 2.4-GHz band. Good agreement between measured and computed results is obtained.      

Robust porous SiOCH/Cu interconnects with ultrathin sidewall protection liners

Robust porous low-k/Cu interconnects have been developed for 65-nm-node ultralarge-scale integrations (ULSIs) with 180-nm/200-nm pitched lines and 100-nm diameter vias in a single damascene architecture. A porous plasma-enhanced chemical vapor deposition (PECVD)-SiOCH film (k=2.6) with subnanometer pores is introduced into the intermetal dielectrics on the interlayer dielectrics of a rigid PECVD-SiOCH film (k=2.9). This porous-on-rigid hybrid SiOCH structure achieves a 35% reduction in interline capacitance per grid in the 65-nm-node interconnect compared to that in a 90-nm-node interconnect with a fully rigid SiOCH. A via resistance of 9.7 /spl Omega/ was obtained in 100-nm diameter vias. Interconnect reliability, such as electromigration, and stress-induced voiding were retained with interface modification technologies. One of the key breakthroughs was a special liner technique to maintain dielectric reliability between the narrow-pitched lines. The porous surface on the trench-etched sidewall was covered with an ultrathin plasma-polymerized benzocyclobuten liner (k=2.7), thus enhancing interline time-dependent dielectric breakdown reliability. The introduction of a porous material and the control of the sidewall are essential for 65-nm-node and beyond scaled-down ULSIs to ensure high levels of reliability.     

Full‐wave optoelectrical modeling of optimized flattened light‐scattering substrate for high efficiency thin‐film silicon solar cells

The flattened light‐scattering substrate (FLiSS) is formed by a combination of two materials with a high refractive index mismatch, and it has a flat surface. A specific realization of this concept is a flattened two‐dimensional grating. When applied as a substrate for thin‐film silicon solar cells in the nip configuration, it is capable to reflect light with a high fraction of diffused component. Furthermore, the FLiSS is an ideal substrate for growing high‐quality microcrystalline silicon (µc‐Si:H), used as bottom cell absorber layer in most of multijunction solar cell architectures. FLiSS is a three‐dimensional structure; therefore, a full‐wave analysis of the electromagnetic field is necessary for its optimal implementation. Using finite element method, different shapes, materials, and geometrical parameters were investigated to obtain an optimized FLiSS. The application of the optimized FLiSS in µc‐Si:H single junction nip cell (1‐µm‐thick i‐layer) resulted in a 27.4‐mA/cm² implied photocurrent density. The absorptance of µc‐Si:H absorber exceeded the theoretical Yablonovitch limit for wavelengths larger than 750 nm. Double and triple junction nip solar cells on optimal FLiSS and with thin absorber layers were simulated. Results were in line with state‐of‐the‐art optical performance typical of solar cells with rough interfaces. After the optical optimization, a study of electrical performance was carried out by simulating current–voltage characteristics of nip solar cells on optimized FLiSS. Potential conversion efficiencies of 11.6%, 14.2%, and 16.0% for single, double, and triple junction solar cells with flat interfaces, respectively, were achieved. Copyright © 2012 John Wiley & Sons, Ltd.