An EM‐based adaptive multiple target tracking filter

Tracking targets of interest is one of the major research areas in radar surveillance systems. We formulate the problem as incomplete data estimation and apply EM to the MAP estimate. The resulting filter has a recursive structure analogous to the Kalman filter. The advantage is that the measurement‐update deals with multiple measurements in parallel and the parameter‐update estimates the system parameters on the fly. Experiments tracking separate targets in parallel show that tracking maintenance ratio of the proposed system is better than that of NNF and RMS position error is smaller than that of PDAF. Also, the system parameters are correctly obtained even from incorrect initial values. Copyright © 2001 John Wiley & Sons, Ltd.     

Effects of solidification structure on fatigue crack initiation and fatigue strength in Al−Si−Mg cast alloys

Rotating-bending uniaxial fatigue tests and micro-fatigue crack initiation tests were carried out using a permanent mold cast (PMC) and semi-solid die cast (SDC) with Al−7%Si−0.35%Mg composition in order to examine the relationship between solidification structures and fatigue behaviors. The crack length was measured using a replication method. Fatigue strength was improved in SDC, which was almost consistent with the predicted fatigue strength using the size of Si particle cluster. Resistance to fatigue crack initiation and fatigue strength were improved in SDC owing to the finer Si cluster and to higher ultimate tensile strength. Fatigue crack in PMC was preferentially initiated at pores. For SDC, the fatigue crack was initiated at the Si particle/matrix interface, and then sucessively grew along eutectic cell boundaries.     

A novel cyclic process using CaSO4/CaS pellets for converting sulfur dioxide to elemental sulfur without generating secondary pollutants: Part II. Hydrogen reduction of calcium-sulfate pellets to calcium sulfide

The reduction of calcium sulfate to produce calcium sulfide is a part of the cyclic process for converting sulfur dioxide to elemental sulfur that is described in Part I. The kinetics of the hydrogen reduction of nickel-catalyzed calcium-sulfate pellets were investigated using a thermogravimetric analysis (TGA) technique at reaction temperatures between 1023 and 1088 K and hydrogen partial pressures between 12.9 and 86.1 kPa. The reactivity of nickel-catalyzed calcium-sulfate pellets was demonstrated by the conversion of 70 pct fresh nickel-catalyzed calcium sulfate to calcium sulfide in 20 minutes at 1073 K under a hydrogen partial pressure of 86.1 kPa. Furthermore, the reactivity remained relatively intact after ten cycles of reactions and regenerations. This observed characteristic of the pellets is important because the solids must be reusable for repeated cycles to avoid generating secondary pollutants. The nucleation and growth rate expression was found to be useful in describing the kinetics of the reaction, which had an activation energy of about 167 kJ/mol (∼40 kcal/mol) in all reaction cycles except for the first regenerated samples that were lower at 146 kJ/mol (35 kcal/mol). The reaction order with respect to hydrogen partial pressure was 0.22 in all cycles with the exception of the first regenerated sample for which it was 0.37.     

An experimental study of carrier heating on channel noise in deep-submicrometer NMOSFETs via body bias

In this paper, RF noise in 0.18-mum NMOSFETs concerning the contribution of carrier heating and hot carrier effect is characterized and analyzed in detail via a novel approach that modulates the channel carrier heating and number of hot carriers using body bias. We confirm qualitatively a negligible role of hot carrier effect on the channel noise in deep-submicrometer MOSFETs. For a device under reverse body bias (V_b), even though the increase in hot carrier population is clearly characterized by dc measurements, the device high-frequency noise is found to be irrelevant to the increase in the channel hot carriers. Experimental results show that the high-frequency noise is slightly reduced with the increase in |V_b|, and can be qualitatively explained by secondary effects such as the suppression of nonequilibrium channel noise and substrate induced noise. The reduction of NF_min and R_n with the increase in |V_b| may provide a possible methodology to finely adjust the device high-frequency noise performance for circuit design     

A continuum-based modeling of MEMS devices for estimating their resonant frequencies

A continuum-based modeling of coupled electrostatics-structure interactions is presented for the frequency computations of MEMS devices. The present general formulation of electrostatics accounting for free space is validated first by specializing it to one-dimensional uniform motion of conducting surfaces and comparing the resulting electrostatics to conventional lumped models. The general coupled electrostatics-structure interactions are then applied for the prediction of resonant frequencies of MEMS devices due to bias-voltage changes and temperature variations. Comparisons of predicted resonant frequencies obtained by the present coupled electrostatics-structure interaction models with experimental results available in the literature demonstrate that the proposed continuum-based interaction modeling yields high-confidence predictions of resonant frequencies of MEMS devices.     

使用无线网络分析器调试ZigBee协议系统

本文详细探讨了使用无线网络分析器调试ZigBee协议系统的基本方法,从而便于更好地确保网络的可靠性.     

A 0.9 V 92 dB Double-Sampled Switched-RC Delta-Sigma Audio ADC

A 0.9 V third-order double-sampled delta-sigma audio ADC is presented. A new method using a combination of a switched-RC technique and a floating switched-capacitor double-sampling configuration enabled low-voltage operation without clock boosting or bootstrapping. A three-level quantizer with simple dynamic element matching was used to improve linearity. The prototype IC implemented in a 0.13 CMOS process achieves 92 dB DR, 91 dB SNR and 89 dB SNDR in a 24 kHz audio signal bandwidth, while consuming 1.5 mW from a 0.9 V supply. The prototype operates from 0.65 V to 1.5 V supply with minimal performance degradation.     

Poly(butylene terephthalate)–clay nanocomposites prepared by melt intercalation: morphology and thermomechanical properties

Nanocomposites based on poly(butylene terephthalate) (PBT) and an organoclay (Cloisite 30B) were prepared by melt blending using a twin‐screw extruder. Two kinds of PBTs, ie PBT‐A and PBT‐B, with different inherent viscosities (η_inh), were used for this study (η_inh of PBT‐A and PBT‐B were 0.74 and 1.48, respectively). Dispersion of the clay layers in the PBT nanocomposites was characterized by using X‐ray diffraction (XRD) and transmission electron microscopy (TEM). Tensile and dynamic mechanical properties and non‐isothermal crystallization temperatures of the nanocomposites were also examined. Nanocomposites based on the higher‐viscosity PBT (PBT‐B) showed a higher degree of exfoliation of the clay and a higher reinforcing effect when compared to the composites based on the lower‐viscosity PBT (PBT‐A). The clay nanolayers dispersed in PBT matrices lead to increases in the non‐isothermal crystallization temperatures of the PBTs, with such increases being more significant for the PBT‐B nanocomposites than for the PBT‐A nanoocomposites. Copyright © 2004 Society of Chemical Industry     

Phase behavior of ternary blends containing dimethylpolycarbonate,tetramethylpolycarbonate and poly[styrene‐co‐(methyl methacrylate)] copolymers (or polystyrene)

The miscibility and phase behavior of ternary blends containing dimethylpolycarbonate (DMPC), tetramethylpolycarbonate (TMPC) and poly[styrene‐co‐(methyl methacrylate)] copolymer (SMMA) have been explored. Ternary blends containing polystyrene (PS) instead of SMMA were also examined. Blends of DMPC with SMMA copolymers (or PS) did not form miscible blends regardless of methyl methacrylate (MMA) content in copolymers. However, DMPC blends with SMMA (or PS) blends become miscible by adding TMPC. The miscible region of ternary blends is compared with the previously determined miscibility region of binary blends having the same chemical components and compositions. The region where the ternary blends are miscible is much narrower than that of binary blends. Based on lattice fluid theory, the observed phase behavior of ternary blends was analyzed. Even though the term representing the Gibbs free energy change of mixing for certain ternary blends had a negative value, blends were immiscible. It was revealed that a negative value of the Gibbs free energy change of mixing was not a sufficient condition for miscible ternary blends because of the asymmetry in the binary interactions involved in ternary blends. Copyright © 2004 Society of Chemical Industry