Synergistic Flame Retardant Effects of Carbon Nanotube-Based Multilayer Nanocoatings

In an effort to develop highly functionalized flame retardant materials, hybrid nanocoatings are prepared by alternately depositing a positively charged polyaniline (PANi) and negatively charged montmorillonite (MMT) using the layer-by-layer (LbL) assembly technique. Carbon nanotubes (CNTs) are employed in polymer nanocomposites as effective reinforcement, where nanotubes are stabilized in MMT aqueous solution. The 3D structure and high density of CNTs deposited in the PANi/CNTs-MMT multilayers produce thicker and heavier coatings in comparison to the LbL assemblies without CNTs. Vertical and horizontal flame testing show that the incorporation of CNTs improves fire resistance. Additionally, cone calorimetry reveals that stacking two nanomaterials (MMT and CNTs) in a single coating shows a significant reduction in peak heat release rate (up to 51%), total smoke release (up to 47%), and total heat release (up to 37%) for the polyurethane foam. The enhancement of flame retardancy is attributed to a synergistic effect; MMT serves as a physical barrier that retards the diffusion of heat and gas. The addition of CNTs strengthens the thermal stability and high char yield. These results, coupled with the simplicity with which the LbL deposition is applied, present a viable alternative to halogen-free flame retardant nanocoatings to natural and synthetic fibers.     

Mg-Sr牺牲阳极显微组织和电化学性能的研究

研究了Mg-Sr牺牲阳极的显微组织和电化学性能的特征.结果表明,Mg-Sr牺牲阳极的晶粒尺寸随Sr含量的增加而减小;当Sr质量分数为0.19%时,电流效率达到58.56%,开路电位达到-1.735 VSCE;Sr的质量分数再增加,Mg-Sr阳极的电流效率降低,开路电位正移.研究认为,Sr的质量分数为0.19%时,晶界析出的Mg17Sr2相（弱阴极相）和α-Mg基体（阳极相）组成电偶对,阻碍了阳极晶间腐蚀,减少了晶粒大块脱落, 且Sr能够和Mg、Fe形成弱阴极性化合物降低Fe的危害,电流效率升高,同时晶粒细化,晶界面积变大,杂质相分布更均匀,开路电位负移;Sr含量大于0.19%时,过量的Mg17Sr2相作为阴极相加大了阳极的自腐蚀,电流效率下降,开路电位正移.     

An electrochemical method for the preparation of Mg–Li alloys at low temperature molten salt system

Mg–Li alloys have been prepared by electrolysis in a molten salt electrolyte of 50% LiCl–50% KCl (mass%) at low temperature of 420–510 °C. The effects of electrolytic temperature and cathodic current density on alloy formation rate and current efficiency were studied. For the deposition of metallic lithium on the cathode consisting of solid Mg and liquid Mg–Li, both electrolytic temperature and cathodic current density have no obvious influence on current efficiency; while for the deposition of metallic lithium on the solid magnesium cathode, both electrolytic temperature and cathodic current density greatly affect alloy formation rate and current efficiency. The optimum electrolysis condition is—molten salt mixture, LiCl:KCl = 1:1 (mass%), electrolytic temperature: 480 °C, cathode current density: 1.13 A cm⁻². Mg–Li alloys with low lithium content (about 25 wt% Li) were prepared via electrolysis at low temperature following by thermal treatment at higher temperature.     

Ga2O3薄膜材料氧敏性能的研究

实验以三氯化镓为原料,柠檬酸为络合剂,通过NH3·H2O调节pH值,得到透明稳定的前躯体溶胶,红外光谱分析表明上述溶胶在向凝胶转变过程中,发生镓与柠檬酸的络合,并在干燥过程中依靠氢键形成大分子聚合物.采用提拉涂覆溶胶-凝胶法在多晶氧化铝基片表面形成凝胶膜后,经800℃下热处理,凝胶膜转化为单斜相β-氧化镓陶瓷薄膜.重复镀膜和热处理及超声清洗过程8个～10个周期,最后在800℃下烧结,保温1h,得到粒径为50nm～100nm左右的多孔纳米薄膜.采用自制系统检测β-Ga2O3薄膜的氧敏性能,结果表明Fe掺杂的氧化镓薄膜材料,在400℃～800℃范围内,在理论空燃比附近,电阻突变幅度大于2个数量级,具有较高的灵敏度.     

Ni3Al中B和Mg的非平衡晶界共偏聚

在1023－1373K的初始温度和0.05-268.91K/s的冷速范围内，用Auger剖层分析确定含B和Mg的Ni3Al合金中B和Mg的非平衡晶界共偏聚行为，按照溶质－空位复合体迁移机制所导出的描述非平衡晶界偏聚的扩散速率方程解析表达式，很好地模拟了本实验结果，并确定了Ni3Al-B-Mg合金中B及B－空位复合体，Mg及Mg-空位复合体的扩散系数及复合体激活能。     

机械加工设备中满足人机安全的典型控制电路分析

介绍了机械加工设备中人机安全的等级标准，详细分析了满足不同安全等级标准的典型控制电路。     

铜基形状记忆合金马氏体相变宏观形状应变特征

利用X射线衍射仪、透射电镜、扫描电镜、原子力显微镜等研究了Cu-18Al-9Mn-3.4Zn(摩尔分数,%)形状记忆合金的马氏体晶体结构、亚结构以及马氏体相变宏观形状应变特征.结果表明:该合金的马氏体晶体结构为18R结构,亚结构为层错;单变体马氏体表面浮凸呈"( ) "型,浮凸高度为400～500nm,浮凸宽度为2 000～2 400 nm;多变体马氏体表面浮凸呈"N"型和"山尖"型,浮凸高度为200～400 nm,浮凸宽度为1 000～1 800nm;浮凸角均为8°～12°;马氏体相变符合G-T模型的双切变特征,惯习面为(113)面.     

压铸模与铝合金金属间化合物的形成与分解

为了研究压铸模与铝合金金属间化合物的形成与分解过程,进行了热浸铝试验.试验结果表明金属间化合物的形成与分解是一个连续不断的循环过程,两者之间的相互关系导致了钢基的失重以及体积的减少.     

Defect classification using a new feature for pulsed eddy current sensors

The objective of this study is to identify defects such as surface cracks, subsurface defects and metal losses using feature based pulsed eddy current sensors. A new feature, termed as the rising point, related to the propagation time of electromagnetic waves in metallic targets is proposed for defect classification. Experimental studies of the validation, robustness of the new feature of rising time are reported. In addition to other features, defects can be detected and quantified robustly and lift-off can also be derived from the rising time. Conclusion and further work are derived on the basis of the findings.     

吹喷氧化物质点改善铁基合金的高温耐磨性

为了节省能源,国内外广泛开展了煤的流化床燃烧技术的研究。然而,流化床中埋管材料及其上面所焊鳍片材料耐高温磨蚀性能的提高,是推广这一技术的关键。采用共沉法或机械合金化方法已成功地制成氧化物弥散强化高温合金,不仅高温强度可以维持到合金的熔点附近,而且可以改善高温耐磨性,但这类合金制造工艺复杂、成本高,不适宜大量用于能源工业。向钢水中吹喷氧化物质点可以明显提高镇静钢的室温和高温强度,而且价