Study of the morphology and mechanical properties of polypropylene composites with silica or rice‐husk

The mechanical, morphological behavior and water absorption characteristics of polypropylene (PP) and silica, or PP and rice‐husk, composites have been studied. The silica used in this study as filler was a commercial type produced from soluble glass or rice husks. The compatibilizing effect of PP grafted with monomethyl itaconate (PP‐g‐MMI) and/or with vinyltriethoxysilane (PP‐g‐VTES) as polar monomers on the mechanical properties and water absorption was also investigated. In general, a high loading of the studied fillers in the polymer matrix increases the stiffness and the water absorption capacity. This effect is more noticeable in the tensile modulus of the PP/silica composite with PP‐g‐VTES as compatibilizer. However, the increase of the rice‐husk charge as a natural filler in the PP matrix decreases the stiffness, and in the presence of PP‐g‐MMI as compatibilizer in PP/rice‐husk, the tensile modulus and water absorption of the composite were improved. The better adhesion and phase continuity in the PP/silica and PP/rice‐husk composites with different compatibilizers was confirmed by the morphological study. Copyright © 2004 Society of Chemical Industry     

Optimum power-saving method for power MOSFET width of DC/DC converters

An optimum power metal-oxide-semiconductor field effect transistor (MOSFET) width technique is proposed for enhancing the efficiency characteristics of switching DC-DC converters. By implementing a one-cycle buck DC-DC converter, it is demonstrated that the dynamic power MOSFET width controlling technique has a much improved power reduction whether the load current is light or heavy. The maximum efficiency of the buck converter is ~92% with a 3% efficiency improvement for the heavy load condition. The efficiency is further improved by ~16% for the light load condition as a result of the power reduction from the large power MOSFET transistors. Also proposed is a new error-correction loop circuit to enable a better load regulation than that of previous designs. Compared with the adaptive gate driver voltage technique, the optimum power MOSFET width can achieve a significant improvement in power saving. It is also superior to the low-voltage-swing MOSFET gate drive technique for switching DC-DC converters     

Schwingfestigkeit von Schraube‐Mutter‐Verbindungen

High cycle fatigue of bolted connections Extensive tests regarding the influences on the fatigue of bolt‐nut‐connections of preloading with torsion, of preloading with yielding, of loading with superimposed bending and of the tested lot are processed. These influences are not yet known according to VDI 2230. New testing devices were designed for these tests, which allow a far less expensive operation and may easily be used for bolts of diameters up to M100 and testing frequencies up to 1000 Hz. The validity of fatigue resistance according to VDI 2230 is specified with respect to the test results. The determined influence of the tested lots is unexpectedly high. The manufacturing process of bolts should be improved to minimize this influence.     

Robust State Feedback Control Through Actuators With Generalized Sector Nonlinearities And Saturation

In control systems, actuators often have nonlinear characteristics that can not be neglected. For linear systems driven by actuators satisfying the generalized sector condition, a robust state feedback controller synthesis method is proposed to achieve the ultimate boundedness control. The method is based on the linear matrix inequality approach and is easy to apply. As an important special case of the generalized sector condition, the saturation characteristic of actuators is discussed separately, and non‐conservative results are obtained.     

Synthesis,characterization and properties of functionalized styrene–maleimide copolymers

New functionalized styrene–maleimide copolymers were prepared by free radical copolymerization of styrene (St) and N‐4‐carboxybutylmaleimide (NBMI) in chloroform, using 2,2′‐azobisisobutyronitrile (AIBN) as initiator. Monomer and copolymer characterization was carried out by ¹H‐ and ¹³C‐NMR. Copolymer composition was determined by elemental analysis and Fourier‐transform infrared (FTIR) spectroscopy. The glass transition temperature (from DSC) and the thermogravimetric analysis (TGA) of the copolymers were consistent with the thermal behavior and stability observed for alternating St–maleimide copolymers. St–NBMI copolymers crosslinked with divinylbenzene (DVB) were also synthesized and their cation exchange properties evaluated in order to assess the capacity of the new copolymers to bind metallic ions. Copyright © 2005 Society of Chemical Industry     

Synthesis of 2,7‐Carbazolenevinylene‐Based Copolymers and Characterization of Their Photovoltaic Properties

New electroactive and photoactive conjugated copolymers consisting of alternating 2,7‐carbazole and oligothiophene moieties linked by vinylene groups have been developed. Different oligothiophene units have been introduced to study the relationship between the polymer structure and the electronic properties. The resulting copolymers are characterized by UV‐vis spectroscopy, size‐exclusion chromatography, and thermal and electrochemical analyses. Bulk heterojunction photovoltaic cells from different copolymers and a soluble fullerene derivative, [6,6]‐phenyl‐C₆₁ butyric acid methyl ester, have been fabricated, and promising preliminary results are obtained. For instance, non‐optimized devices using poly(N‐(4‐octyloxyphenyl)‐2,7‐carbazolenevinylene‐alt‐3″,4″‐dihexyl‐2,2′;5′,2″;5″,2″′;5″′,2″″‐quinquethiophenevinylene 1″,1″‐dioxide) as an absorbing and hole‐carrier semiconductor exhibit power conversion efficiency up to 0.8 % under air mass (AM) 1.5 illumination. These features make 2,7‐carbazolenevinylene‐based and related polymers attractive candidates for solar‐cell applications.     

2,4,6‐Trichlorophenol and phenol removal in methanogenic and partially‐aerated methanogenic conditions in a fluidized bed bioreactor

A fluidized bed bioreactor (FBBR) was operated for more than 575 days to remove 2,4,6‐trichlorophenol (TCP) and phenol (Phe) from a synthetic toxic wastewater containing 80 mg L^?1 of TCP and 20 mg L^?1 of Phe under two regimes: Methanogenic (M) and Partially‐Aerated Methanogenic (PAM). The mesophilic, laboratory‐scale FBBR consisted of a glass column (3 L capacity) loaded with 1 L of 1 mm diameter granular activated carbon colonized by an anaerobic consortium. Sucrose (1 g COD L^?1) was used as co‐substrate in the two conditions. The hydraulic residence time was kept constant at 1 day. Both conditions showed similar TCP and Phe removal (99.9 + %); nevertheless, in the Methanogenic regime, the accumulation of 4‐chlorophenol (4CP) up to 16 mg L^?1 and phenol up to 4 mg L^?1 was observed, whereas in PAM conditions 4CP and other intermediates were not detected. The specific methanogenic activity of biomass decreased from 1.01 ± 0.14 in M conditions to 0.19 ± 0.06 mmolCH₄ h^?1 gTKN^?1 in PAM conditions whereas the specific oxygen uptake rate increased from 0.039 ± 0.008 in M conditions to 0.054 ± 0.012 mmolO₂ h^?1 gTKN^?1, which suggested the co‐existence of both methanogenic archaea and aerobic bacteria in the undefined consortium. The advantage of the PAM condition over the M regime is that it provides for the thorough removal of less‐substituted chlorophenols produced by the reductive dehalogenation of TCP rather than the removal of the parent compound itself. Copyright © 2005 Society of Chemical Industry     

Preparation of glucose oxidase immobilized in different carriers using radiation polymerization

Glucose oxidase (EC 1.1.3.4) was immobilized on different polymeric materials using different immobilization techniques (entrapping by γ‐irradiation, and covalent binding using epichlorohydrin). Studies were carried out to increase the thermal stability of glucose oxidase (GOD) for different applications. The activity and stability of the resulting biopolymers have been compared with those of free GOD. The effect of different polyvinyl alcohol/polyacrylamide (PVA/PAAm) compositions of the copolymer carrier on the enzymatic activity of the immobilized GOD was studied. The maximum enzymatic activity was obtained with the composition ratio of PVA/PAAm of 60:40. The behaviour of the free and immobilized enzyme was analysed as a function of pH. A broadening in the pH profile (5.5–8) was observed for immobilized preparations. The activity and stability of the resulting biopolymers produced by immobilization of GOD onto different carriers have been compared, in both aqueous and organic media, with those of the free GOD. The enzyme's tolerance toward both heat and organic solvent was enhanced by immobilization onto polymers. The addition of different concentrations of organic solvents (10–50%, v/v) to the enzyme at higher temperature (60 °C) was found to stabilize the enzyme molecule. The strongest stabilizing effect on the enzymatic activity was achieved at a concentration of 10%. Copyright © 2005 Society of Chemical Industry     

Ozonation of CI Reactive Black 5 using rotating packed bed and stirred tank reactor

This study investigates the ozonation of CI Reactive Black 5 (RB5) by using the rotating packed bed (RPB) and completely stirred tank reactor (CSTR) as ozone contactors. The RPB, which provides high gravitational force by adjusting the rotational speed, was employed as a novel ozone contactor. The same ozone dosage was separately introduced into either the RPB or the CSTR for the investigation, while the experimental solution was continuously circulated within the apparatus consisting of the RPB and CSTR. The decolorization and mineralization efficiencies of RB5 in the course of ozonation are compared for these two methods. Moreover, the dissolved and off‐gas ozone concentrations were simultaneously monitored for the further analysis. As a result, the ozone mass transfer rate per unit volume of the RPB was significantly higher because of its higher mass transfer coefficient and gas–liquid concentration driving force. Furthermore, ozonation kinetics was found to be independent of the gravitational magnitude of an ozone gas–liquid contactor. Therefore, the results suggest employing RPBs as ozone‐contacting devices with the advantage of volume reduction. The experimental results, which can be used for further modeling of the ozonation process in the RPB, also show the requirement of correct design for the RPB. Consequently, the present study is useful for the understanding of practical application of RPBs. Copyright © 2004 Society of Chemical Industry     

Nondestructive evaluation of corrosion by fractal geometry

Fractal geometry is finding its application in the nondestructive evaluation (NDE) of corrosion by characterizing the corrosion surface with fractal dimensions. It was found that corrosion surfaces can be well described by multifractals. Two algorithms were used to obtain the fractal dimensions of a corroded aluminum alloy surface, one being box-counting and another being coherent light scattering. Fractal dimensions were related with the damage caused by corrosion and fatigue.