Fabrication and amplification of Rhodamine B‐doped step‐index polymer optical fiber

A step‐index polymer optical fiber (SI POF) containing Rhodamine B in poly(methyl methacrylate) (PMMA) has been fabricated by a preform technique. Fluorescence of different fiber lengths were observed and discussed. A high gain (23 dB) for a SI POF with 60‐cm length, 400‐μm diameter was obtained. The Rhodamine B content of the doped SI POF is 5 ppm‐wt. The signal wavelength providing the highest gain for a 60 cm SI POF is around 630 nm, and the optimum fiber length is about 60 cm at 10 kW launched pump power. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 681–685, 2004     

ZrO2 和Al2O3支撑的MFI 型沸石分子筛膜:支撑体材料对膜性能的影响

采用水热合成法，以纯SiO2为源物质，在介孔Y2O3掺杂的ZrO2(YZ)及大孔α-Al2O3支撑体上制备出高质量的MFI型沸石分子筛膜，通过H2／n-C4H10气体混合物的渗透分离和p-xylene的蒸发研究了不同支撑体上MFI型沸石分子筛膜分离性能，在较低温度范围，YZ支撑的MFI型沸石分子筛膜中n-C4H10的渗透率比Al2O3支撑的膜高很多，最大n-C4H10与H2的分离率达到500，Al2O3支撑的膜中py-xylene的蒸发流量随时间下降很快，而YZ支撑的膜中的蒸发流量则变化缓慢，用XRD对膜的晶体结构进行分析，通过多种温度下热处理不同支撑体上的膜样品研究了其热稳定性与支持体材料的关系，YZ支撑的MFI型沸石分子筛膜的MFI结构在1000摄氏度后仍能保持，而Al2O3支撑的膜950摄氏度时已完全转变为石英相，研究结果表明，YZ支撑的MFI型沸石分子筛膜比Al2O3支撑的膜表现出更好的厌不性，热稳定性以及抗阻塞性。     

幽门螺杆菌过氧化氢酶基因克隆及表达

目的 克隆幽门螺杆菌(Helicobacter pylori,HP)过氧化氢酶(katA)基因并在大肠杆菌中进行表达。方法 采用PCR扩增幽门螺杆菌katA全长基因,将其克隆入pET-11c载体中,经测序证实后,在大肠杆菌中进行表达,产物用Western blot检测其抗原性并进行N末端氨基酸的测序。结果 幽门螺杆菌katA基因全长1 518bp,编码氨基酸505个。在BL21(DE3)中的表达量约占细菌总蛋白的24.9％,表达产物经SDS-PAGE显示其相对分子质量与软件预测结果 58 000相符,N末端5个氨基酸测序结果与Hp中天然的katA完全一致,经Western blot检测可被 Hp全菌抗血清识别。结论 katA能在大肠杆菌中进行高效表达,具有良好的免疫反应性,可望为研究 Hp的致病机理、实验诊断及亚单位疫苗等提供充足的katA原材料。     

Synthesis of 2‐monoglycerides by alcoholysis of palm oil and tuna oil using immobilized lipases

Commercial immobilized lipases were used for the synthesis of 2‐monoglycerides (2‐MG) by alcoholysis of palm and tuna oils with ethanol in organic solvents. Several parameters were studied, i.e., the type of immobilized lipases, water activity, type of solvents and temperatures. The optimum conditions for alcoholysis of tuna oil were at a water activity of 0.43 and a temperature of 60 °C in methyl‐tert‐butyl ether for ～12 h. Although immobilized lipase preparations from Pseudomonas sp. and Candida antarctica fraction B are not 1, 3‐regiospecific enzymes, they were considered to be more suitable for the production of 2‐MG by the alcoholysis of tuna oil than the 1, 3‐regiospecific lipases (Lipozyme RM IM from Rhizomucor miehei and lipase D from Rhizopus delemar). With Pseudomonas sp. lipase a yield of up to 81% 2‐MG containing 80% PUFA (poly‐unsaturated fatty acids) from tuna oil was achieved. The optimum conditions for alcoholysis of palm oil were similar as these of tuna oil alcoholysis. However, lipase D immobilized on Accurel EP100 was used as catalyst at 40 °C with shorter reaction times (<12 h). This lead to a yield of ～60% 2‐MG containing 55.0‐55.7% oleic acid and 18.7‐21.0% linoleic acid.     

Curing and pyrolysis of cresol novolac epoxy resins containing [2‐(6‐oxido‐6H‐dibenz(c,e)(1,2)oxaphosphorin‐6‐yl)‐1,4‐naphthalenediol]

This study investigates the curing kinetics, thermal properties and decomposition kinetics of cresol novolac epoxy (CNE) with two curing agents, 2‐(6‐oxido‐6H dibenz(c,e)(1,2) oxaphosphorin‐6‐yl)‐1,4‐benzenediol (ODOPN), and phenol novolac (PN). In comparison with the conventional PN system, introducing ODOPN, a phosphorus‐containing bulky pendant group, into CNE increases T_g by 33°C, char yield from 30% to 38%, and LOI from 22 to 31. The DSC curing study reveals that the E_a of the CNE/ODOPN epoxy can be obtained by Kissinger's method. The resulting E_a values indicate that the catalytic effect of EMI is insignificant on CNE/ODOPN but is marked on CNE/PN, whose E_a was reduced from 131.5 to 75.6 KJ/mole. This result may be caused by the fact that the symmetric diol attached to the 1 and 4 positions of the naphthalene ring in ODOPN sets up a steadily resonating structure and inhibits the catalytic action. Further investigating the conversion ratio with curing temperature yielded experimental data that agreed closely with Kaiser's model. The orders of the autocatalyzed reaction, m, and the crosslinking reaction, n, are close to 0.5 and 1.0, respectively, independently of the scan rate. Finally, the TGA decomposition study by Ozawa's method demonstrates that the mean E_a declines with the phosphorus content, because the easy decomposition of the phosphorus compound in the initiation stage facilitates the formation of an insulating layer. However, results in this study further reveal an increasing tendency for E_a with decomposition conversion for an ODOPN/PN mixture with the ODOPN content of over 50%, probably because of the retardation of gas diffusion by the insulating layer of phosphorus compound.     

Preparation of Whisker β-Spodumene Glass–Ceramics

β-spodumene glass–ceramics with a whisker-like microstructure were prepared from the following materials (in wt%): 64.5 SiO₂, 18.0 Al₂O₃, 4.2 Li₂O, 4 ZrO₂, and 8 MgF₂. Scanning electron microscope (SEM) analysis showed that phase separation in the base glass leads to the formation of a primary crystal phase of MgF₂ that promotes the formation of spherical β-spodumene. Whisker spodumene crystals surrounded by spherical crystals are observed at 720°C after 1 h, and the whisker crystals grow at the cost of spherical crystals with increasing temperature and time. The flexural strengths of the glass–ceramics reach a maximum of 228 MPa after heat treatment at 850°C for 1 h.     

Consolidation of sand formation using freon'll gas hydrate

Freon 11 gas hydrate was used to block the pores of four size ranges of sand from 24 mesh to 60 mesh. A 50.8 mm deep bed of sand when thus “frozen” with hydrate could sustain a dfferential water pressure of at least 6895 kPa. A subcooling of about 5 to 6°C below its thermodynamic formation temperature was required to cause the hydrate to form such a plug. Once formed, the hydrate remained stable at temperatures up to its decomposition temperature. The time required for the hydrate crystal to grow to a size large enough to block the pores of the bed was about two hours. The amount of hydrate forming agent required to block the sand pores was found to be approximately that calculated from the ideal composition of the hydrate.     

Lignin‐based polycondensation resins for wood adhesives

Lignin‐based wood adhesives are obtained that satisfy the requirements of relevant international standards for the manufacture of exterior‐grade wood particleboard. Formulations based on low molecular mass lignin and presenting an increase in the relative proportion of reactive points yield better results than the higher molecular mass lignin used in the past. These lignins allow a higher proportion of hydroxymethylation during preparation of methylolated lignins. These lignin‐based adhesives also yield acceptable results at particleboard pressing times that are sufficiently low to be of industrial significance. Lignin‐based wood adhesives, in which a nonvolatile nontoxic aldehyde (glyoxal) is substituted for formaldehyde in their preparation, are prepared and tested for application to wood panels such as particleboard. The adhesives yield good internal bond strength results for the panels, which are good enough to comfortably pass relevant international standard specifications for exterior‐grade panels. The adhesives also show sufficient reactivity to yield panels in press times comparable to that of formaldehyde‐based commercial adhesives. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1690–1699, 2007     

Effect of charge density,molecular weight,and hydrophobicity on polycations adsorption and flocculation of polystyrene latices and silica

Adsorption and flocculation behavior of two series of synthetic polycations was investigated in dispersions of silica and polystyrene latices with various particle size and surface charge densities. Polycations of the first series (polydiallyldimethyl ammonium chloride‐PDADMAC) varied in molecular weight only, while polycations of the second series (derivatives of polymethacrylic acid) varied in both molecular weight and hydrophobicity. We have found that maximum adsorbed amount of high molecular weight PDADMAC on latex particles was nearly independent of the surface charge density when the particle size was comparable to the polymer coil dimensions in solution. Both low and high molecular weight PDADMACs were efficient flocculants, although significantly lower amounts of high molecular weight polyelectrolyte were required for the phase separation in the dispersions due to particles aggregation through “charge patch” mechanism. The increase of polymer hydrophobicity leads to higher adsorbed amounts and broadening of flocculation window by polycations of the second series on both substrates. However, no strong enhancement of segment–surface interactions on hydrophobic substrates was observed. Since formation of multilayers upon adsorption was also excluded, the difference in adsorption and flocculation behavior was related to the more compact conformation of hydrophobically associating derivatives in solution and at the interface. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3422–3429, 2006     

二甲醚燃烧用掺杂钡、镍六铝酸盐催化剂的研究

二甲醚是易液化，便于运输，清洁化的新能源。当作为燃料使用时，采用催化燃烧的方法能使得燃烧的起燃温度降低和提高燃烧转化率，克服了普通燃烧的缺点，实现了清洁燃烧。对二甲醚催化燃烧用的催化剂BaNiAl11O19-δ进行了制备与研究。采用溶胶-凝胶法制备六铝酸盐催化剂BaNiAl11O19-δ,考察其对新能源二甲醚催化燃烧反应的活性，并用TG—DTA对催化剂的性质进行考察。结果表明，加入经800℃焙烧4h后又在1200℃焙烧了2h的催化剂，比未加催化剂的燃烧体系T10降低了50℃。用溶胶一凝胶法制备的六铝酸盐催化剂BaNiAl11O19-δ对二甲醚催化燃烧反应具有较高的催化活性。