Creep and Stress Rupture Behavior of an Advanced Silicon Nitride: Part I, Experimental Observations

Cylindrical buttuohead specimens of an advanced silicon nitride were tested in uniaxial tension at temperatures between 1422 and 1673 K. In the range 1477 to 1673 K, creep deformation was reliably measured using high-temperature contact probe extensometry. Extensive scanning and transmission electron microscopy has revealed the formation of lenticular cavities at two-grain junctions at all temperatures (1422–1673 K) and extensive triple-junction cavitation occurring at the higher temperatures (1644–1673 K). Cavitation is believed to be part of the net creep process. The stress rupture data show stratification of the Monkman–Grant lines with respect to temperature. Failure strain increased with increase in rupture time or temperature, or decrease in stress. Fractography showed that final failure occurred by subcritical crack growth in all specimens.     

Dynamic viscoelasticity of low‐density polyethylene/in‐situ‐grafted carbon black composite

The study on the dynamic viscoelastic properties of grafted carbon black (g‐CB) filled low‐density polyethylene (LDPE) was carried out. Because of formation of CB networking, the characteristic modulus plateau and loss tangent arc appears. Addition of grafting monomer like butyl acrylate (BA) and acroleic acid (AA) enhances the interaction between particles and matrix due to accelerated formation of micronetworking in the composites induced by forming branch chains of AA and BA with multiunit. The decrease of the temperature corresponding to α_c mechanical relaxation together with AA (BA) addition given by the position of loss tangent (tan δ) peak for LDPE is owed to the formation of long‐chain polymer grafted between CB and the matrix, which facilitates the slip of the lamella of LDPE. The influence of maleic anhydride (MA) on enhancing interaction between LDPE and CB is not so pronounced, as compared with AA and BA because of no formation of long chain between CB particle and polymer matrix. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4127–4132, 2006     

旋风分离器内颗粒运动规律的数值模拟

采用单颗粒动力学模型计算了旋风分离器内颗粒的运动轨迹。计算结果表明：进入旋风分离器的颗粒绝大多数在环形空间内就被甩向器壁；从入口上部进入的部分较小颗粒由于局部二次流作用而上升形成顶灰环；还有少量颗粒进入下部分离空间。在下部分离空间内，有灰斗返气夹带上来的颗粒，处于内旋流的颗粒则有可能随上升气流而逃逸，所以一定的分离空间高度有利用颗粒的二次再分离。     

无底柱分段崩落法采矿进路受力过程分析

在使用无底柱分段崩落法的矿山,大都存在着地压现象。其主要表现是采矿进路和联络道的变形破坏。对采矿进路在开挖和回采过程中各阶段受力情况的分析表明,进路的变形、破坏主要是受到岩体初始静应力、爆破动应力和矿柱支撑应力的综合作用的结果。     

螺带式搅拌器在假塑液中的混合及放大的研究

本文综合研究了螺带式搅拌器在假塑性液体中的混合特性及动力特性，测定了双螺带，内外螺带及螺带螺旋３种类型搅拌器的功率常数Ｋｐ和Ｍｅｔａｎｅｒ常数Ｋｓ，并得出混匀操作和传质工艺过程的放大准则。     

Modeling of photocatalytic oxidation of VOCs in a packed bed reactor under continuous and discontinuous illuminations

In this paper, a mathematical model is presented to describe the photocatalytic degradation of VOCs in a packed bed reactor. Here, the adsorption of VOCs on the wall of the reactor is taken into account and the diffusion of VOCs in the axial direction is neglected. First-order kinetics is used to describe the photocatalytic oxidation of VOCs. The analytical solution of the present model is obtained by traveling wave method. The solution shows that the reactor performance is totally dependent on the inlet concentration of VOCs when the time is large enough. The present model is validated through the experimental result of the photocatalytic oxidation of trichloroethylene in a packed bed and the predicted results accord well with the experimental data. The influence of flow rate and inlet concentration on the performance of the reactor is discussed in detail. High flow rate offers high reaction rate and low conversion efficiency. The different inlet conditions and different reaction patterns are also investigated. The model would be useful to estimate the rate constant and help to the design of the reactor.     

Demineralization of a UK bituminous coal using HF and ferric ions

A UK bituminous coal has been used to study demineralization by two-stage chemical leaching. The first-stage uses hydrofluoric acid (HF) at 65 °C and reduces the ash content from 5.30 wt% to 1.37 wt% by mainly removing Al and Si containing minerals. Subsequent leaching by ferric ions decreases the ash content further to 990 ppm by removing most of the pyrite and fluorides formed during the HF leaching. Calorific value of the coal shows no change following leaching, which suggests no oxidation is occurring to the coal carbonaceous matrix. The mercury and sulfur contents after the two-stage leaching sequence decrease by 40% and 26%, respectively.     

Ozone-Based Advanced Oxidation Processes for the Decomposition of N-Methyl-2-Pyrolidone in Aqueous Medium

The present study investigates the decomposition of N-Methyl-2-Pyrolidone (NMP) using conventional ozonation (O₃), ozonation in the presence of UV light (UV/O₃), hydrogen peroxide (O₃/H₂O₂), and UV/H₂O₂ processes under various experimental conditions. The influence of solution pH, ozone gas flow dosage, and H₂O₂ dosage on the degradation of NMP was studied. All ozone-based advanced oxidation processes (AOPs) were efficient in alkaline medium, whereas the UV/H₂O₂ process was efficient in acidic medium. Increasing ozone gas flow dosage would accelerate the degradation of NMP up to certain level beyond which no positive effect was observed in ozonation as well as UV light enhanced ozonation processes. Hydrogen peroxide dosage strongly influenced the degradation of NMP and a hydrogen peroxide dosage of 0.75 g/L and 0.5 g/L was found to be the optimum dosage in UV/H₂O₂ and O₃/H₂O₂ processes, respectively. The UV/O₃ process was most efficient in TOC removal. Overall it can be concluded that ozonation and ozone-based AOPs are promising processes for an efficient removal of NMP in wastewater.     

基于蜜罐技术的主动防护网络入侵探究

随着信息技术的快速发展,网络安全问题日益突出,如何保护网络安全成为人们研究的重点.在实际工作过程中应用蜜罐技术来进行主动防护网络入侵是一种新方式.由蜜罐技术和分布式代理构成的防护体系,能够有效降低攻击检测误报率.网络安全形势日益复杂的背景下加强对蜜罐技术的研究具有重要意义.本文将重点探讨如何利用蜜罐技术来实现对网络入侵的主动防护.