Incremental transmission loss allocation under pool dispatch

Incremental transmission loss analysis has been used for decades, but recent interest in its application to loss allocation calls for new in-depth results. This paper demonstrates that, for incremental methods to be applied correctly in loss allocation, it is first necessary to specify the load distribution and loss supply strategies. Incremental loss allocation among bus power injections is shown to be arbitrary and, therefore, open to challenge as discriminatory. Loss allocation is possible among incremental loads and/or generators, but the proportion of the total losses assigned to either one is arbitrary. Unique, nonarbitrary incremental loss allocations are however possible among the "equivalent" incremental bilateral exchanges between generators and loads. From these basic components it is possible then to calculate the allocation among generators or loads in any specified proportion. The main results, although developed initially for small increments, are extended to large variations. Finally, a general incremental loss allocation algorithm is developed and tested     

Simulation of magnetic component models in electric circuitsincluding dynamic thermal effects

It is essential in the simulation of power electronics applications to model magnetic components accurately. In addition to modeling the nonlinear hysteresis behavior, eddy currents and winding losses must be included to provide a realistic model. In practice the losses in magnetic components give rise to significant temperature increases which can lead to major changes in the component behavior. In this paper a model of magnetic components is presented which integrates a nonlinear model of hysteresis, electro-magnetic windings and thermal behavior in a single model for use in circuit simulation of power electronics systems. Measurements and simulations are presented which demonstrate the accuracy of the approach for the electrical, magnetic and thermal domains across a variety of operating conditions, including static thermal conditions and dynamic self heating     

Modern Aluminum and Magnesium Alloys and Composite Materials Based on Them

Aluminum and magnesium alloys are the base structural materials in aircraft and spacecraft engineering. The main stages of the development and introduction of light alloys are described.     

International statements and definitions of the precautionary principle

The precautionary principle (PP), according to one of its definitions, says that lack of certainty, given the current scientific and technological knowledge, shall not delay effective and proportionate actions to prevent hazards, taking into account cost-benefit considerations. Rather than being a single principle, a variety of statements of the PP are found in international treaties and other documents. Apart from any specific legal force of the documents, countries (e.g., France) have used these statements as a starting point for their own guidance documents and regulations for addressing specific environmental and health issues, for example regulation of genetically modified organisms. Thus, any discussion of the precautionary principle must address a complex legal and regulatory situation. We briefly review different statements of the PP and important commentary, largely from the European Union. We provide references to the original source documents (many of which are found in English on the World Wide Web).     

Influence of Edible Films upon the Moisture Loss and Microstructure of Dietetic Sucrose-Free Sponge Cakes during Storage

The kinetics of changes in the bound water content in dietetic sucrose-free sponge cakes (DC) during storage was investigated. The effect of edible films of polymyxan, pectin, xanthan, and carboxymethylcellulose upon this kinetics was also investigated. The quantitative changes in both states of water (slightly bound water and strongly bound water) were registered by combined dynamic analysis (thermogravimetry analysis, TGA, and differential thermal analysis, DTA). The moisture changes in DC crumb were analyzed by drying out to constant mass. The rate constants were determined according the equation q = q_oe^-kt. The values of rate constants 'k', in day^-1, concerning the different edible films were as follows: for crumb moisture is (8.00 ≤ k ≤ 12.47) × 10^-3, for bound water is (3.07 ≤ k_w ≤ 6.26) × 10^-2, for slightly bound water is (4.22 ≤ k₁ ≤ 8.49) × 10^-2 and for strongly bound water is (2.02 ≤ k₂ ≤ 5.62) × 10^-2 as compared to 18.53 × 10^-3, 7.16 × 10^-2, 9.04 × 10^-2, and 5.36 × 10^-2 in the uncovered DC, respectively. The best water-retaining effect in respect to crumb moisture during storage was ascertained in the use of polymyxan and xanthan films. The lowest rate constant values for bound water and its two states were measured for DC covered with pectin. The relation between the kinetics of both bound water states during storage and ageing of the crumb of DC covered with different edible films and the crumb microstructure was represented. By means of scanning electron microscope was read the smallest change in crumb microstructure of pectin-covered DC on the sixth day of storage.     

Crisis phenomena upon evaporation in grid capillary and porous coatings and arterial structures of heat pipes

The article presents the results of experimental investigations of critical (limit) heat fluxes upon evaporation on porous coatings, and it substantiates the physical model of the process.Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 49, No. 4, pp. 607–614, October, 1985.     

Structure and composition of guanidine acrylate, guanidine methacrylate, their homopolymers, and copolymers with diallyldimethylammonium chloride

Structures and compositions of the monomers guanidine acrylate and guanidine methacrylate, their homopolymers, and copolymers with diallyldimethylammonium chloride enriched in acrylate comonomer units were determined. It was shown that ampholytic copolymers, owing to their ionic nature, contained comonomeric guanidine acrylate or methacrylate units and diallyldimethylammonium chloride units, as well as the acrylate comonomer with the diallyl counterion and polymeric acrylate and diallyl ion pairs. It follows from IR and ¹H NMR data that guanidine methacrylate has the same structure (with two hydrogen bonds) in the solid state and in solutions. Guanidine acrylate structures in the solid state and in dimethylsulfoxide are identical and analogous to guanidine methacrylate structure in this solvent. In water, the guanidine acrylate structure has another type of hydrogen bonding (with one hydrogen bond, where the proton is shifted toward the guanidine group). These features of hydrogen bonding of guanidine acrylate and guanidine methacrylate are also retained in their homopolymers and copolymers with diallyldimethylammonium chloride. It was shown that the thermal stability of the copolymers was higher than that of their homopolymers, confirming the formation of intramolecular ion pairs of oppositely charged units of ampholytic copolymers. Moreover, the thermal stability of guanidine methacrylate-diallyldimethylammonium chloride copolymers is higher than that of guanidine acrylate-diallyldimethylammonium chloride copolymers.     

On the nonuniformity of a capillary flow

It is established that the capillary rise of a liquid has an oscillatory character, in contrast to the commonly accepted opinion that a vertical capillary is filled at a monotonically varying velocity. The value of the tangential shear stress arising in an ascending liquid is evaluated for ethyl alcohol and distilled water.     

Experimental Electronuclear Setup at the Institute of Theoretical and Experimental Physics

The purpose and current construction status, at the Institute of Theoretical and Experimental Physics, of an experimental electronuclear setup, combining a pulsed proton linear accelerator (36 MeV, 0.5 mA) and a subcritical blanket thermal-power assembly 100 kW, are discussed. The main equipment is already available or is being built in industry. The setup can be used to investigate the dynamics of the interaction of a linac–driver and a subcritical reactor and problems concerning the accelerator–driver and the target–blanket assembly. The proton beams and neutron fluxes will be used for applied purposes. In the future it will be possible to increase substantially the current and energy of the proton beam.     

Implementation of a self-timed segmented bus

We propose an asynchronous structure for implementation on a SoC. An intersegment topological arrangement preserves parallelization and, through a so-called central arbiter, efficiently organizes communication with high signaling speed in the proposed structure. Researchers proposed the concept of segmenting buses primarily for multicomputer architectures. More recent approaches address on-chip implementation of segmented buses. We present an asynchronous segmented-bus architecture targeted for the modular design of high-performance SoC applications. The structure not only enables faster operation than a conventional bus system but also offers lower power consumption per transferred data item. This is possible because segmentation is realized in such a way that the majority of data transfers in the system are intrasegment transactions on relatively short wires with low or moderate capacitive loads.