The multi-fuzzy N-soft set and its applications to decision-making

Neural Computing and Applications - The goal of this paper is to introduce a novel hybrid model called multi-fuzzy N-soft set, and to design an adjustable decision-making methodology for solving...     

Soret and Dufour effects between two rectangular plane walls with heat source/sink

This study addresses the thermo‐diffusion and the diffusion‐thermo phenomena in a semi‐infinite absorbent channel whose walls are contracting/expanding, with heat source/sink effects. The governing partial differential equations with suitable boundary conditions are transformed to a system of dimensionless ordinary differential equations. An analytic solution of the problem has been found using a technique called homotopy analysis method (HAM). HAM gives consistently valid answers to the problem over an extensive variety of parameters and also provides better accuracy. To validate the analytical results, a comparison has been presented with a numerical solution calculated by using the parallel shooting method. The effects of dimensionless parameters, that is, deformation parameter, Reynolds number, Soret and Dufour numbers, and heat source/sink parameter on the expressions of velocity, temperature, and concentration profiles are analyzed graphically to understand the physics of the deformable channel. It has been noted that the velocity across the channel is higher for the expanding channel, as compared to that for the contracting channel. Also the Soret and Dufour number increases the temperature of the fluid, and decreases the concentration. The temperature profile has an increasing behavior in the case of heat source, and a decreasing behavior in the case of heat sink.     

Linear friction welding of Ti6Al4V: experiments and modelling

Linear friction welding of the Ti6Al4V alloy is studied. A new definition of the energy input rate is proposed, based on an integration over time of the in-plane force and velocity; a strong correlation with the upset rate is then found. The effective friction coefficient is estimated to be 0·5±0·1 for varying frequencies and amplitudes, with only a weak dependence on the processing conditions displayed. A model is proposed that accounts for both the conditioning and equilibrium stages of the process, which is shown to be in good agreement with the experimental data. The model is used to study the mechanism by which the flash is formed. A criterion is proposed by which the rippled nature of its morphology can be predicted.     

Inferring kinetic dissolution of NaCl in aqueous glycol solution using a low-cost apparatus and population balance model

An experimental methodology for inferring brine dissolution rate in monoethylene glycol (MEG) solutions at different temperatures using a webcam combined with a mathematical model is presented. The measurement system is designed to track the RGB (red, green, and blue) colour variations during the dissolution process. A dynamic model augmented with the population balance equation is applied to describe the dissolution process. Moreover, the dissolution rate is consistently related to the temperature and MEG concentration through the driving force based on the Gibbs energy and chemical affinity. The applied low-cost measurement apparatus proved to be a useful resource for tracking the dissolution dynamics in a wide range of undersaturation.     

Simulation of characteristics of double-junction solar cells based on ZnSiP2 heterostructures on silicon substrate

Design and operation modes of double-junction monolithic lattice-matched solar cells based on the ZnSiP₂/Si system of materials have been calculated. The effect of the photoactive region thickness and minority carrier lifetime in ZnSiP₂ layers on the efficiency of conversion of the incident solar light energy into electrical power was determined. It is shown that solar cells based on ZnSiP₂/Si heterostructures can provide efficiencies of 28.8% at AM1.5D, 100 mW/cm², and 33.3% at AM1.5D, 200 W/cm².     

Temperature cycling and its effect on mechanical behaviours of highporosity chalks

Temperature history can have a significant effect on the strength of water-saturated chalk.In this study,hydrostatic stress cycles are applied to understand the mechanical response of chalk samples exposed to temperature cycling between each stress cycle,compared to the samples tested at a constant temperature.The total accumulated strain during a stress cycle and the irreversible strain are reported.Chalk samples from Kansas(USA)and Mons(Belgium),with different degrees of induration(i.e.amount of contact cementation),were used.The samples were saturated with equilibrated water(polar)and nonpolar Isopar H oil to quantify water weakening.All samples tested during 10 stress cycles with varying temperature(i.e.temperature cycled in between each stress cycle)accumulated more strain than those tested at constant temperatures.All the stress cycles were performed at 30℃.The two chalk types behaved similarly when saturated with Isopar H oil,but differently when saturated with water.When saturated with water,the stronger Kansas chalk accumulated more total strain and more irreversible strain within each stress cycle than the weaker Mons chalk.     

Matrix Transformation in Boron Containing High-Temperature Co–Re–Cr Alloys

An addition of boron largely increases the ductility in polycrystalline high-temperature Co–Re alloys. Therefore, the effect of boron on the alloy structural characteristics is of high importance for the stability of the matrix at operational temperatures. Volume fractions of ε (hexagonal close-packed—hcp), γ (face-centered cubic—fcc) and σ (Cr₂Re₃ type) phases were measured at ambient and high temperatures (up to 1500 °C) for a boron-containing Co–17Re–23Cr alloy using neutron diffraction. The matrix phase undergoes an allotropic transformation from ε to γ structure at high temperatures, similar to pure cobalt and to the previously investigated, more complex Co–17Re–23Cr–1.2Ta–2.6C alloy. It was determined in this study that the transformation temperature depends on the boron content (0–1000 wt. ppm). Nevertheless, the transformation temperature did not change monotonically with the increase in the boron content but reached a minimum at approximately 200 ppm of boron. A probable reason is the interplay between the amount of boron in the matrix and the amount of σ phase, which binds hcp-stabilizing elements (Cr and Re). Moreover, borides were identified in alloys with high boron content.