A Monte Carlo simulation study of the mechanical and conformational properties of networks of helical polymers. I. General concepts

We study the mechanical and conformational properties of networks of helical polymers with a combination of Monte Carlo simulations based on the Wang-Landau algorithm and the three-chain model. We find that the stress-strain behavior of these networks has novel features not observed in typical networks made of synthetic polymers. In particular, we find that as these networks are stretched they first strengthen, then soften and finally strengthen again. This non-monotonic behavior of the stress correlates with the one of the helical content and is rationalized by the elongation-induced formation and melting of the helical structure of the polymer. We complement these results with a study of other conformational properties of the polymer strands that clarify the molecular mechanisms behind the mechanical behavior of these networks. Finally, we present a qualitative comparison of some of our results with the theoretical ones recently reported by Kutter and Terentjev.     

High Pressure Conductivity and Photoconductivity of Polyveratrole

Summary Electropolymerization of o-(CH₃O)₂C₆H₄ (Veratrole) in dry acetonitrile/tetrabutylammonium tetrafluoroborate at platinum electrode, yields a green polymeric conducting solid. As the pressure is increased, the material becomes more conductive, but sharp changes towards lower conductivity occur at 4.2 and 6.2 metric tons pressure, probably due to phase transitions. The photoconductivity shows an exponential increase as temperature is increased, but it shows reversible changes at 200 K, 225 K and 250 K during slow warming, also attributable to phase transitions. Photoconductivity of Polyveratrole increases with the radiation frequency, being higher under blue light than under red of infrared radiation and there is a linear increase of photoconductivity with radiation density. Conductivity transients show that the conductivity increases exponentially with time to the saturation point within few minutes, and it also decreases exponentially when the light is turned off and the circuit is open. This behaviour can be explained by formation and encounter of electron and hole as current carriers. A preliminary study indicates a piezoelectric effect for the material. absorption spectroscopy allowed the measurements of the material band gap.     

The effect of plastic deformation on Al2CuLi (T 1) precipitation

The enhancement ofT ₁ precipitation in Al-Li-Cu alloys by plastic deformation prior to aging (that is, cold work) and the subsequent increase in alloy strength is investigated. The increased understanding of the role of matrix dislocations in the nucleation and growth ofT ₁ plates, discussed in the previous paper,^[1] permits a detailed study of the phenomenon. In this paper, the effect of different levels of plastic strain on theT ₁ particle distributions as a function of aging time at 190 °C is quantified, and the subsequent influence on tensile properties is thereby described. The effect of plastic deformation is shown to decrease theT ₁ plate length and thickness, increase the number density by almost two orders of magnitude, increase the yield strength by 100 MPa, while simultaneously reaching peak strength in 20 pct of the time required without plastic deformation. Formerly Graduate Student, Department of Materials Science, University of Virginia,     

Construction and performance of a multiparameter focal plane detector for use on a QMG/2 magnetic spectrometer

The design, construction and performance of a modular, two pressure focal plane detector, 550 mm long, 1000 mm deep and with an active height of 60 mm are described. The detector has been operated with ions ranging from 50 MeV ¹H to 200 MeV ³⁶S. Typical results achieved are 0.5 mm and 0.3° for the spatial and angular resolutions, and 0.7% and 3% for the total energy and energy loss measurements. A height signal is also provided.     

Untersuchungen zum Korrosionsverhalten von AlLi-Legierungen

Corrosion behaviour of aluminium-lithium alloys The AlLiMgCu alloy 8090 was studied in its texturated fine grained version “A” and in its recrystallized coarse grain structured version “C” in different artificially aged conditions in reference to several other AlLi alloys, each in its heat treatment condition of practical interest, and to the convetional alloy 2024 T3. The subject of research was the general corrosion behaviour of semifinished AlLi products, particularly sheet material, under alternate and permanent immersion conditions in neutral 3.5% sodium chloride solution; the stress corrosion behaviour was studied under constant load in the long transverse direction according to ASTM G44 and G49. The underaged conditions, which are the relevant conditions for technical application of the 8090 “A” and “C” sheets, showed an approximately equivalent or even better corrosion behaviour in comparison to the lithium-free alloy 2024 T3 in the corrosion tests with unloaded specimens. The threshold above which the AlLi alloy 8090 in some heat treatment conditions is attacked by stress corrosion cracking within the 30 days lasting constant load test depends on alloy composition, testing direction, grain size, stretch-forming, artificial ageing condition, surface pretreatment and the specimens' dimensions.     

The effect of temperature on crazing mechanisms in polystyrene

At room temperature scission is the dominant mechanism for the modification of the entanglement network required for craze formation in polystyrene, but as the temperature is increased towardsT _g, there is the possibility that disentanglement processes may contribute. These will be most important for short chains. If disentanglement can occur, a molecular weight dependence of the crazing stress as a function of temperature will result. This prediction is tested by straining thin films of a range of monodisperse samples of polystyrene at temperatures between 40 and 90° C. The nature of the ensuing deformation has been characterized by transmission electron microscopy. It is observed that whereas only crazing occurs over the entire temperature range for the lowest molecular weight sample, shear processes become important for higher molecular weight materials. For the longest chains, crazing is almost entirely suppressed at 80° C, with the preferential formation of shear deformation zones occurring. These observations are consistent with the idea that disentanglement is playing a significant role in craze formation at sufficiently high temperatures.     

Lowpass approximations of a constant amplitude with arbitrary phase and delay

A review is made of recent developments to the simultaneous lowpass approximation problem of amplitude, phase and delay. the closed from solutions (reciprocal and non-reciprocal) are expressed in terms of the arbitrary phase and delay polynomials (APD).