Low-leakage-current and low-operating-voltage buried photodiode for a CMOS imager

A low-leakage current and low-operating-voltage buried-photodiode structure of CMOS image sensors has been developed. The new structure adopted a modified fabrication process as well as an additional shallow p+ layer structure that covers the entire surface of the deep n-type photodiode. The required operating voltage for complete charge transfer from the photodiode is 3.3 V. Furthermore, the leakage current level allows high-quality images comparable to those of CCD image sensors.     

Fracture and general yield for carbon steel pipes with local wall thinning

Monotonic bending tests without internal pressure are conducted on 4 and 3.5 in. diameter full-scale carbon steel pipe specimens with local wall thinning in order to evaluate the structural integrity of power plant piping. The local wall thinning is simulated as erosion/corrosion metal loss. The eroded area of the wall thinning is subjected to tensile or compressive stress by applied bending moment. The maximum moments obtained from the tests are compared with the plastic collapse moments based on the net-section stress approach. The net-section stress approach based on flow stress σ_f gives a conservative estimation, sometimes overly conservative. Although the net-section approach based on ultimate tensile strength σ_u gives a slightly non-conservative estimation for some cases, the calculated values are close to the experimental data. Using the net-section stress approach based on σ_u, the eroded depth and the angle at which a pipe undergoes general yielding were obtained.     

Release of formaldehyde and melamine from tableware made of melamine-formaldehyde resin

The relationship between the concentrations of formaldehyde and melamine released into 4% acetic acid from dishes and bowls made of melamine-formaldehyde resin was determined. The average concentrations in the migration solution after the sample had been treated at 60, 80, and 95 degrees C for 30 min with 4% acetic acid were 0.0 +/- 0.1, 0.5 +/- 0.4 and 3.0 +/- 2.2 ppm, respectively for formaldehyde and 0.04 +/- 0.07, 0.21 +/- 0.20 and 1.19 +/- 1.18 ppm, respectively for melamine. The correlation between the concentrations of formaldehyde and melamine released at 95 degrees C was y=0.4858x-0.2728 (r=0.8860), where y is melamine concentration (ppm), x is formaldehyde concentration (ppm) and r is the correlation coefficient. The molar concentration ratios of formaldehyde to melamine (F/M ratio) were 15.4 +/- 11.6 at 80 degrees C and 14.9 +/- 10.1 at 95 degrees C. Hence the release of both migrants was affected by temperature but the F/M ratio was not affected. The release of both compounds was was increased on repetition of the migration test at 95 degrees C but their concentrations remained constant after the tenth and seventeenth repetitions of the treatment. During this period, the F/M ratio decreased according to the equation 1n y=-1.4344 1n x+3.7814 (r=-0.9984) for a sample before the tenth repetition of the treatment and remained between 1.7 and 1.9 after the twelfth repetition, where y is the F/M ratio and x is the number of repetitions of the treatment.     

Identification of acid-stable carmine in imported apple syrup product

An unknown red pigment was purified from an apple syrup product imported from Canada, using a DIAION HP-20 column with methanol as the eluent. By spectroscopic means and chemical synthesis, the isolated pigment was identified as 4-aminocarminic acid, which is the major pigment of acid-stable carmine (a red colorant illegal in Japan). In addition, HPLC and TLC methods were proposed to detect this illegal colorant. While the color of carminic acid changed from yellow to red in the pH range of McIlvaine buffer (3.0-7.0), the color of 4-aminocarminic acid was always red, and also the ultraviolet/visible (UV/Vis) spectra did not change. These characteristics are useful to distinguish 4-aminocarminic acid from carminic acid.     

Observation of fluorapatite formation under hydrolysis of tetracalcium phosphate in the presence of KF by means of soft X-ray emission and absorption spectroscopy

The effect of fluoride on the hydrolysis of tetracalcium phosphate (TTCP; Ca₄(PO₄)₂O) in 0.1 mol/l KH₂PO₄ containing 62–83 mmol/l KF was studied with the help of X-ray fluorescence measurements. Fluorine X-ray emission and absorption spectra of the final product of hydrolysis and reference samples (CaF₂ and Ca₅(PO₄)₃F) were measured at Beamline BL-2C of Photon Factory (PF, Tsukuba). Based on these measurements we concluded that hydrolysis of TTCP in the presence of KF converts it into fluorapatite. Formation of CaF₂, which is often found in the hydrolysis of hydroxyapatite at high fluoride concentration, was not observed.     

Determination method of polysorbates in powdered soup by HPLC

A method for qualitative and quantitative analyses of polysorbates in powdered soup by HPLC was studied. Polysorbates in samples were extracted with acetonitrile after rinsing with n-hexane to remove fats and oils. The extract was cleaned up using a Bond Elut silica gel cartridge (500 mg). The cartridge was washed with ethyl acetate and polysorbates were eluted with a small amount of acetonitrile-methanol (1:2) mixture. The eluate was treated with cobalt thiocyanate solution to form a blue complex with polysorbate. In order to determine polysorbate, the complex was subjected to HPLC with a GPC column, using a mixture of acetonitrile-water (95:5) as a mobile phase, with a detection wavelength of 620 nm. The recoveries of polysorbate 80 added to powdered soups were more than 75% and the determination limit was 0.04 mg/g. When the proposed method was applied to the determination of polysorbates in 16 commercial samples of powdered soup for instant noodles and seasoning consomme, no polysorbates were detected in any sample.     

Estimation of preservative concentrations in foods and their daily intake based on official inspection results in Japan in fiscal year 1998

The mean concentration and daily intake of five preservatives were estimated based on the results of an analysis of 89,927 samples of food obtained in official inspections by Japanese local governments in fiscal year 1998. The mean concentration of benzoic acid was 9.5% of the allowable limit, and those of dehydroacetic acid, p-hydroxybenzoic acid, propionic acid, and sorbic acid were 1.5%, 5.7%, 1.7%, and 23.9%, respectively. Daily intake levels of these preservatives per person estimated from the concentration and daily consumption of foods were 6.23 mg, 0.0303 mg, 1.02 mg, 8.10 mg, and 25.0 mg, respectively, and assuming a body weight of 50 kg, the amounts of benzoic acid, p-hydroxybenzoic acid, and sorbic acid consumed were 2.5%, 0.2%, and 2.0% of their acceptable daily intakes, respectively. These values were similar to those obtained based on the results of the official inspections in fiscal years 1994 and 1996.     

Material labeling of soft plastic toys and plasticizers in polyvinyl chloride products

We investigated the labeling and content of plasticizers of soft plastic toys. First, we investigated material labeling in 96 products purchased in fiscal years 2000 and 2001. Among these products, 43% of those purchased in fiscal 2000 and 68% of those purchased in fiscal 2001 were labeled. We then investigated the kinds and amounts of plasticizers in 73 soft polyvinyl chloride (PVC) toys. Three kinds of phthalates and six other kinds of plasticizers were detected in the soft PVC toys. Diisononyl phthalate, di(2-ethylhexyl) phthalate, diisononyl adipate, and O-acetyl tributyl citrate were detected at high frequency, and in large amounts. The average total content of all plasticizers was 280 mg/g for the products purchased in fiscal 2000 and 227 mg/g for those in fiscal 2001. In fiscal 2001, antioxidants, 4-nonylphenol, and bisphenol A were investigated in addition to plasticizers.     

Acrylate Copolymer/Ultraviolet Curable Oligomer Blends as Pressure-sensitive Adhesives

For the blends of acrylate copolymer [poly(2-ethylhexyl acrylate-co-acrylic acid); P(2EHA-AA)] with ultraviolet (UV) curable oligomer [urethane acrylate oligomer; UAO], pressure-sensitive adhesive (PSA) properties, such as peel adhesion, probe tack, and holding power were examined. The values of peel adhesion and probe tack of the P(2EHA-AA)/UAO blends were dramatically reduced by UV irradiation. On the other hand, all blends had a high holding power even if these blends were cured by UV irradiation. The mechanism of reduced PSA properties was investigated via dynamic mechanical properties, DSC, and dynamic contact angle (DCA). The peel adhesion decreased monotonically with increasing storage modulus, E′, and loss modulus, E″, for all non-UV and UV-cured blends. Since modulus values and glass transition temperatures, Tg, of these blends after UV irradiation were higher than those of these blends before UV irradiation, we judged that the reduced peel adhesion and probe tack values were caused by the modulus increase and the Tg increase due to UV irradiation. In other words, the ability of the deformation energy of UV-cured blends to influence the adhesive tests was reduced by the curing process. The DCAs of non-UV-cured blends were the same as those of UV-cured blends. We presumed that the segment mobility of the polymer chain on the surface did not contribute to the reduced peel adhesion and probe tack values.     

Investigation on the Surface Vortex Formation During Mechanical Stirring with an Axial-Flow Impeller Used in an Aluminum Process

Metallurgical and Materials Transactions B - The present study investigated the mechanism of surface vortex formation in an aluminum melt vessel stirred by an axial-flow impeller mechanically. The...