Microstrip stepped impedance resonator bandpass filter with an extended optimal rejection bandwidth

Bandpass filters with an optimal rejection bandwidth are designed using parallel-coupled stepped impedance resonators (SIRs). The fundamental (f/sub o/) and higher order resonant harmonics of an SIR are analyzed against the length ratio of the high-Z and low-Z segments. It is found that an optimal length ratio can be obtained for each high-Z to low-Z impedance ratio to maximize the upper rejection bandwidth. A tapped-line input/output structure is exploited to create two extra transmission zeros in the stopband. The singly loaded Q(Q/sub si/) of a tapped SIR is derived. With the aid of Q/sub si/, the two zeros can be independently tuned over a wide frequency range. When the positions of the two zeros are purposely located at the two leading higher order harmonics, the upper rejection band can be greatly extended. Chebyshev bandpass filters with spurious resonances up to 4.4f/sub o/, 6.5f/sub o/, and 8.2f/sub o/ are fabricated and measured to demonstrate the idea.     

Mechanical spectroscopy in commercial Fe–6 wt.% Si alloys between 400 and 1000 K

Mechanical spectroscopy, neutron diffraction and differential scanning calorimetry (DSC) were performed on commercial Fe–6 wt.% Si alloy after quenching from high temperature. The damping spectrum shows a peak at around 800 K and an associated modulus defect. The modulus shows an increase during the second and subsequent heating runs. In addition, an anomaly in the modulus behavior has been found at around 400 K. Different thermal treatments allows to obtain two different recovery degrees of the quenched-in defects. The influence of the recovery degree on the 800 K internal friction peak and on the anelastic modulus has been evaluated and confirm the validity of the grain boundary mechanism associated to this peak. Experimental results are discussed on the basis of recovery and ordering processes.     

Wavelength-tunable 40-GHz picosecond harmonically mode-locked fiber laser source

We demonstrate a novel 40-GHz mode-locked fiber laser that utilizes a single active device to provide both gain and mode-locking. The laser produces pulses as short as 2.2 ps, is tunable over a 27-nm band centered at 1553 nm, and exhibits long-term stability without cavity-length feedback control. The pulse train at 1556 nm was used in a 40-Gb/s transmission experiment over 45 km with a low 0.4-dB power penalty.     

Modification of ASM3 for the determination of biomass adsorption/storage capacity in bulking sludge control.

The selector activated sludge (SAS) systems are known to prevent excessive growth of filamentous microorganisms responsible for bulking sludge, but these systems were hardly ever modelled. This study aimed to develop a model capable of predicting rapid substrate removal in the SAS systems. For this purpose, the Activated Sludge Model No. 3 (ASM3) was extended with three processes (adsorption, direct growth on the adsorbed substrate under aerobic or anoxic conditions). The modified ASM3 was tested against the results of batch experiments with the biomass originating from two full-scale SAS systems in Germany. The endogenous biomass was mixed with various readily biodegradable substrates (acetate, peptone, glucose and wastewater) and the utilisation of substrate (expresses as COD) and oxygen uptake rates (OURs) were measured during the experiments. In general, model predictions fitted to the experimental data, but a considerable number of kinetic (5) and stoichiometric (2) parameters needed to be adjusted during model calibration. The simulation results revealed that storage was generally a dominating process compared to direct growth in terms of the adsorbed substrate utilisation. The contribution of storage ranged from 65-71% (Plant A) and 69-92% (Plant B).     

Robust decoding of variable-length encoded Markov sources using a three-dimensional trellis

In this letter, we present an improved index-based a-posteriori probability (APP) decoding approach for the error-resilient transmission of packetized variable-length encoded Markov sources. The proposed algorithm is based on a novel two-dimensional (2D) state representation which leads to a three-dimensional trellis with unique state transitions. APP decoding on this trellis is realized by employing a 2D version of the BCJR algorithm where all available source statistics can be fully exploited in the source decoder. For an additional use of channel codes the proposed approach leads to an increased error-correction performance compared to a one-dimensional state representation.     

Multilayer power printed structures suitable for controlling EMI noises generated in power converters

Electromagnetic interference (EMI) noises generated in power converters are diffused on the surface of conductors. This means influences occur from radiated EMI noises emitted from power transmission lines as well as conducted EMI noises transmitted from them. EMI noises diffusing on the surface of conductors are generally difficult to control using conventional concentrated constant theory. Thus, a new approach based on distributed constant circuit theory is needed in order to control EMI noises. A power converter structure to control EMI noises using multilayer power printed circuit technology is studied in this paper. A structure which can control EMI noises should simultaneously satisfy two conditions, i.e., one to shut down and one to attenuate EMI noises. The structure satisfying these conditions is studied through simulations using the Transmission-Line Modeling Method. The simulations show that the diffusion of EMI noises is controlled by dividing the flow of currents produced by EMI noises into the horizontal and perpendicular directions. That is, the horizontal current flow is controlled inside using the differences in the resistance produced from differences between inner and outer diameter of power transmission lines and the perpendicular current flow can be controlled by properly designing the thickness of the dielectric layer sandwiched between P-and N-power transmission lines with the symmetrical structure. Moreover, it is confirmed by simulations and experiments that the attenuation of EMI noises is affected by the width of the power transmission lines. It is expected that the results obtained in this paper can provide important rules when designing power converters with EMI noise control functions which use the multilayer power printed circuit technology.     

Analogue switch for very low-voltage applications

A new analogue switch suitable for operation at very low-voltage supply in a standard CMOS technology is presented. The proposed switch is based on 'quasi-floating-gate' transistors and has a simple and compact structure. For illustrative purposes, two sample-and-hold circuits operating from a single supply voltage close to the threshold voltage of a transistor, and using the proposed technique, are presented. Experimental results obtained from prototypes in a 1.5 /spl mu/m CMOS technology are provided.