Radiometric sensor for temperature control of food processing

This paper describes a novel planar antenna sensor created for the purpose of noninvasive temperature measurements using microwave radiometry. In order to improve radiometric measurements in industrial applications, a new generation of sensors is introduced, composed of a metallic sheet. Simulations based upon the method of moments is used both to design and to determine their electromagnetic performances. This paper also describes a radiometric device using these sensors to measure and control the temperature of food products during deep freezing processes. The results and discussions are presented.     

Mass Transfer in a Flat Gas/Liquid Interface using non‐Newtonian Media

Gas/liquid mass transfer has been investigated using a stirred vessel gas/liquid contactor using non‐Newtonian media and carbon dioxide as absorbent and gas phase, respectively. The volumetric mass transfer coefficients at different operational variables have been determined. Non‐Newtonian media (liquid phase) were prepared as aqueous solutions of sodium carboxymethyl cellulose salt. The influence of the rheological properties, polymer concentration, stirring rate, and gas flow rate on mass transfer was studied for these liquid phases. Kinematic viscosity and density experimental data were used to calculate the average molecular weight corresponding to the polymer employed. The Ostwald model has been used to fit the rheological behavior of aqueous solutions of the polymer employed as absorbent phase. Reasonably good agreement was found between the predictions of the proposed models and the experimental data of mass transfer coefficients.     

Asymptotic performance of single parity-check product codes

This article investigates the asymptotic performance of single parity-check (SPC) product codes (PCs) from a decoding point of view. Specifically, the probability of bit error is bounded before and after the decoding of each dimension, similar to the analysis of "iterated codes" by Elias (1954). It is shown that the asymptotic probability of bit error can be driven to zero as the number of dimensions, and hence the block length, increases at signal-to-noise ratios (SNRs) within 2 dB of capacity over the additive white Gaussian noise (AWGN) channel.     

High-efficiency LEDs of 1.6–2.4 µm spectral range for medical diagnostics and environment monitoring

High efficient LED structures covering the spectral range of 1.6–2.4 μm have been developed on the basis of GaSb and its solid solutions. The electroluminescent characteristics and their temperature and current dependences have been studied. The radiative and nonradiative recombination mechanisms and their effect on the quantum efficiency have been investigated. A quantum efficiency of 40–60% has been obtained in the quasi-steady mode at room temperature. A short-pulse optical power of 170 mW was reached. __________ Translated from Fizika i Tekhnika Poluprovodnikov, Vol. 37, No. 8, 2003, pp. 996–1009. Original Russian Text Copyright ? 2003 by Stoyanov, Zhurtanov, Astakhova, Imenkov, Yakovlev.     

Optimal mean-square prediction of the mobile-radio fading envelope

Long-range prediction of the mobile-radio fading envelope is an enabling technology for many fading compensation approaches. Because the fading envelope is well modeled as a bandlimited process, it has special predictability properties. In this paper, we find a linear predictor that is optimal in the mean-square sense when the predictor impulse response is energy constrained. This solution may be used to determine the minimum mean squared error of a prediction based on past values that are corrupted with estimation errors.     

PNNI-based control plane for automatically switched optical networks

Much effort has been spent on the definition of control plane protocols for automatically switched optical networks (ASON). Most of the proposals brought into the standardization for an International Telecommunications Union-Telecommunication Sector, Internet Engineering Task Force, and Optical Internetworking Forum are based on Internet protocol concepts. One such proposal is the generalized multi-protocol label switching (GMPLS), an extension of the MPLS traffic engineering control plane model that includes nonpacket switched technologies (time, wavelength, and fiber switching). Recently, the potential use of private network-network interface (PNNI) in ASONs has been discussed as an alternative proposal by the standardization bodies. The goal of this paper is to appropriately adapt asynchronous transfer mode into an optical PNNI (O-PNNI) protocol that can be used as the control plane of ASONs. The paper also provides a critical viewpoint on the potential usage of either O-PNNI or GMPLS control plane and analyzes the pros and cons of each. The methodology adopted toward devising O-PNNI hinges on reviewing PNNI along with ASON recommendations in order to determine the set of PNNI features that require adaptation. Having identified these features we engineer and present appropriate solutions relating to routing, signaling and addressing aspects.     

Experimental real-time detector of GSM terminals

The authors present an experimental real-time GSM terminal detector, to be installed in a restricted area. The detector triggers terminal signaling, which can be captured.     

Exposed Die-Top Encapsulation Molding for an Improved High- Performance Flip Chip BGA Package

The recent advancement in high- performance semiconductor packages has been driven by the need for higher pin count and superior heat dissipation. A one-piece cavity lid flip chip ball grid array (BGA) package with high pin count and targeted reliability has emerged as a popular choice. The flip chip technology can accommodate an I/O count of more than five hundreds500, and the die junction temperature can be reduced to a minimum level by a metal heat spreader attachment. None the less, greater expectations on these high-performance packages arose such as better substrate real estate utilization for multiple chips, ease in handling for thinner core substrates, and improved board- level solder joint reliability. A new design of the flip chip BGA package has been looked into for meeting such requirements. By encapsulating the flip chip with molding compound leaving the die top exposed, a planar top surface can be formed. A, and a flat lid can then be mounted on the planar mold/die top surface. In this manner the direct interaction of the metal lid with the substrate can be removed. The new package is thus less rigid under thermal loading and solder joint reliability enhancement is expected. This paper discusses the process development of the new package and its advantages for improved solder joint fatigue life, and being a multichip package and thin core substrate options. Finite-element simulations have been employed for the study of its structural integrity, thermal, and electrical performances. Detailed package and board-level reliability test results will also be reported