Rapidly tunable optical add-drop multiplexer utilising relaxed beam splitters

A polarisation-independent four-port electro-optic tunable filter in the 1530 nm wavelength regime utilising non-polarising relaxed beam splitters and strain-induced polarisation converters on LiNbO₃ with 16 nm tuning range and 46 ns tuning speed is reported.     

Effects of various post-treatments on carbon nanotube films for reliable field emission

In this report, the FE characteristics of carbon nanotubes (CNTs) treated using both thermal annealing and mechanical coatings on the as-grown CNTs systematically studied. It was found that in the high temperature annealed samples, CNTs were attacked at its root during annealing due to a small amount of oxygen, and were pulled out of the substrate in places after FE measurements because of the contact resistance. However, for the mechanically coated samples both with spin on glass (SOG) and polymethyl methacrylate (PMMA), CNTs were found to be nearly intact after FE measurements and showed reliable FE characteristics over repeatable voltage scan. The reliability of CNTs during FE could be owing to the strong adhesion of CNTs to the substrate both by SOG and PMMA coatings.     

Fatigue crack propagation properties from small sized rod specimens

Mechanical properties characterization is needed in many industrial applications yet sufficient amount of material for fabricating standard-sized testing specimens is often not available. Techniques for testing miniaturized specimen must be adopted. Much effort has been made to develop techniques for impact, fracture toughness and tensile properties of sub-sized specimens. Work on the testing of fatigue properties is more limited. In this study, fatigue crack propagation behavior is evaluated from the growth of surface crack in a cylindrical rod under tension. Rods of various lengths and diameters were tested. As the size of the rod specimen is reduced, the fatigue crack growth rate tends to increase when correlated using the stress intensity factor range. This increase is explained largely by the decrease in the degree of premature crack closure in the small specimens. Valid fatigue crack growth data can be obtained among the specimens examined except on the crack growth on the surface of the smallest specimen, which has a length of 26 mm and diameter of 8 mm. Even so, valid data can still be elucidated on the latter specimen if the interior growth is considered. The dimensions of the latter specimen allow fatigue properties to be evaluated using broken remnants from impact or other test specimens.     

Chemical vapor deposition of amorphous ruthenium-phosphorus alloy films

Chemical vapor deposition growth of amorphous ruthenium-phosphorus films on SiO₂ containing ∼ 15% phosphorus is reported. cis-Ruthenium(II)dihydridotetrakis-(trimethylphosphine), cis-RuH₂(PMe₃)₄ (Me = CH₃) was used at growth temperatures ranging from 525 to 575 K. Both Ru and P are zero-valent. The films are metastable, becoming increasingly more polycrystalline upon annealing to 775 and 975 K. Surface studies illustrate that demethylation is quite efficient near 560 K. Precursor adsorption at 135 K or 210 K and heating reveal the precursor undergoes a complex decomposition process in which the hydride and trimethylphosphine ligands are lost at temperatures as low at 280 K. Phosphorus and its manner of incorporation appear responsible for the amorphous-like character. Molecular dynamics simulations are presented to suggest the local structure in the films and the causes for phosphorus stabilizing the amorphous phase.     

Effects of reducing and oxidizing atmospheres on the PTCR characteristics of porous n-BaTiO3 ceramics by adding polyethylene glycol

Donor doped BaTiO₃ (n-BaTiO₃) ceramics were fabricated by adding polyethylene glycol (PEG) at 20 wt %. The effects of reducing and oxidizing atmospheres on the PTCR characteristics of the porous n-BaTiO₃ ceramics were investigated. The PTCR characteristics of the porous n-BaTiO₃ ceramics is strongly affected by chemisorbed oxygen at the grain boundaries and are recovered as the atmosphere is changed from the reducing gas to oxidizing gas. The low room-temperature resistivity of the porous n-BaTiO₃ ceramics in reducing atmospheres may be caused by the decrease in potential barrier height, which originates from an increase in the number of electrons owing to the desorption of chemisorbed oxygen atoms at the grain boundaries. In addition, the high room-temperature resistivity of the porous n-BaTiO₃ ceramics in oxidizing atmospheres may be caused by the increase in potential barrier height, which results from the adsorption of chemisorbed oxygen atoms at the grain boundaries.     

At least N+1 finite transmission zeros using frequency-variant negative source-load coupling

A second-order cross-coupled combline filter which has three finite transmission zeros is presented. The problem of the frequency-invariant coupling in a real circuit is introduced. To make extra transmission zeros, a top metalized dielectric block is used.     

The stress-whitened damage zone of PVC blends

The stress-whitened damage zone that formed ahead of a semicircular notch during slow tensile loading has been measured from optical micrographs of translucent blends of poly(vinyl chloride) (PVC) with experimental chlorinated polyethylene (CPE) resins. When the zone was small, the plane strain condition applied and from the elastic stress distribution a constant mean stress condition was found at the boundary of the crescent-shaped zone. The critical mean stress did not depend on the chlorine content or the chlorine distribution of the experimental CPE resin used in the blend. While the critical mean stress decreased as the amount of CPE in the blend was increased, the critical volume strain, calculated from the bulk modulus, was independent of composition and was thought to be the controlling parameter for stress-whitening. When the zone was larger, the shape was qualitatively described by concepts of stress redistribution in the presence of a plastic zone ahead of the notch. Macroscopic flow and necking were only detected near the maximum in the stress-displacement curve.     

Catalytic dehydrogenation of ethylbenzene with carbon dioxide: promotional effect of antimony in supported vanadium–antimony oxide catalyst

Alumina-supported vanadium oxide, VO_x/Al₂O₃, and binary vanadium–antimony oxides, VSbO_x/Al₂O₃, have been tested in the ethylbenzene dehydrogenation with carbon dioxide and characterized by S_BET, X-ray diffraction, X-ray photoelectron spectroscopy, hydrogen temperature-programmed reduction and CO₂ pulse methods. VSbO_x/Al₂O₃ exhibited enhanced catalytic activity and especially on-stream stability compared to VO_x/Al₂O₃ catalyst. Incorporation of antimony into VO_x/Al₂O₃ increased dispersion of active VO_x species, enhanced redox properties of the systems and formed a new mixed vanadium–antimony oxide phase in the most catalytically efficient V_0.43Sb_0.57O_x/Al₂O₃ system.     

DC and AC characteristics of sub-50-nm MOSFETs with source/drain-to-gate nonoverlapped structure

A MOSFET structure with a nonoverlapped source/drain (S/D) to gate region was proposed to overcome the challenges in sub-50-nm CMOS devices. Key device characteristics were investigated by extensive simulation study. Fringing gate electric field through the spacer induces an inversion layer in the nonoverlap region to act as an extended S/D region. An oxide spacer is used to reduce parasitic gate overlap capacitance. A reasonable amount of inversion electrons were induced under the spacers. Internal physics, speed characteristics, short channel effects, and RF characteristics were studied with the nonoverlap distance at a fixed metallurgical channel length of 40 nm. The proposed structure had good drain-induced barrier lowering and V/sub T/ rolloff characteristics and showed reasonable intrinsic gate delay and cutoff frequency compared to those of an overlapped structure.