Development and experimental evaluation of aerodynamic lens as an aerosol inlet of single particle mass spectrometry

This study described a development and an experimental evaluation of an efficient aerodynamic lens inlet of the single particle mass spectrometry. Several key designing parameters and systematic factors were investigated for the whole lens system through a full numerical simulation. From many tests for various designs of the system, we showed that Mach number was not an independent parameter but interrelated well with flow Reynolds numbers and pressures upstream of the orifices. By manipulating the parameters, we showed for the first time a possibility that there exist a universal correlation between optimal Stokes number and a new factor incorporating the other dimensionless variables and a design parameter. The universality was confirmed by the full simulation results. We demonstrated that the new design of the system was capable of focusing ultrafine aerosols in the size range of 30–700 nm. At two different operating conditions, the formations of sub-millimeter beams of 30–300 nm NaCl aerosols are verified by light scattering imaging as well as microprobe observation of deposited aerosol beams. Finally, the measured sizes of aerosol beams agree reasonably well with those from the simulations as a function of particle size.     

Structure and processability of iodinated poly(vinyl alcohol). IV. Drawability of the films iodinated at solution before casting

The drawability of iodinated at solution before casting (IBC) polyvinyl alcohol films prepared by casting aqueous solutions of 10 wt % PVA containing 15.2, 39.8, 83.2, 117.0, and 140.1% was examined with a tensile tester at 20–60°C. The tensile behavior of IBC films showed that the yield and breaking loads were much lower, and the breaking elongation was even higher than those of the unoriented iodinated after casting (IAC) films as well as the untreated PVA films. The maximum draw ratios of the films with the weight gain of 15.2, 39.8, 83.2, 117, and 140.1% were 4.5, 5.5, 8.5, 8.0, and 7.5, respectively, which were achieved at 20°C in all. The crystallinity of all films increased by the maximum draw, regardless of crystallinity before drawing. The crystalline structure was recovered to the original PVA crystalline lattice by deiodination. Amorphous orientation and initial moduli increased with the maximum draw ratio, while the orientation of crystals was constant. The orientation and moduli increased up to the weight gain of 83.2%, whose highest draw ratio and initial modulus were 8.5 and of 7.1 GPa, respectively, and then decreased. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

The Fabrication and Characterization of Single‐Component Polymeric White‐Light‐Emitting Diodes

By using Ni⁰‐mediated polymerization, we have systematically synthesized a series of fluorene‐based copolymers composed of blue‐, green‐, and red‐light‐emitting comonomers with a view to producing polymers with white‐light emission. 2,7‐Dibromo‐9,9‐dihexylfluorene, {4‐(2‐[2,5‐dibromo‐4‐{2‐(4‐diphenylamino‐phenyl)‐vinyl}‐phenyl]‐vinyl)‐phenyl}‐diphenylamine (DTPA), and 2‐{2‐(2‐[4‐{bis(4‐bromo‐phenyl)amino}‐phenyl]‐vinyl)‐6‐tert‐butyl‐pyran‐4‐ylidene}‐malononitrile (TPDCM) were used as the blue‐, green‐, and red‐light‐emitting comonomers, respectively. It was found that the emission spectra of the resulting copolymers could easily be tuned by varying their DTPA and TPDCM content. Thus with the appropriate red/green/blue (RGB) unit ratio, we were able to obtain white‐light emission from these copolymers. A white‐light‐emitting diode using the polyfluorene copolymer containing 3 % green‐emitting DTPA and 2 % red‐emitting TPDCM (PG3R2) with a structure of indium tin oxide/poly(3,4‐ethylenedioxythiophene):poly(styrene sulfonic acid)/PG3R2/Ca/Al was found to exhibit a maximum brightness of 820 cd m^–2 at 11 V with Commission Internationale de L'Eclairage (CIE) coordinates of (0.33,0.35), which are close to the standard CIE coordinates for white‐light emission (0.33,0.33).     

Inhibition of natural killer cell cytotoxicity by cell growth-related molecules

Certain MHC class I molecules on target cells are known to inhibit the cytotoxic action of NK cells. By using monoclonal antibody (mAb) Cho-1, we have found inhibitory non-MHC class I cell surface molecules that are noncovalently-associated with 200 kDa and 40 kDa antigens. Poly I-C-induced rat NK cells were not cytotoxic to rat fetus-derived fibroblast WFB cell line. In contrast, NK cells were cytotoxic to H-ras oncogene-induced transformants of WFB, W14 and W31. FACS analysis indicated that mAb Cho-1 reacts with WFB, but not with W14 and W31 cells. Thus, this antigen may disappear concomitantly with cell growth and transformation. Cho-1 antigens were also expressed on other NK-resistant lines, such as mouse BALB3T3 fibroblast, EL-4 lymphoma and human fibroblast HEPM. However, they were not expressed on NK-sensitive mouse YAC-1 and H-ras transformant (Brash) of BALB3T3 cells. Furthermore, treatment of target cells with IFN-gamma clearly induced the cell surface expression of Cho-1 antigens, and conferred a resistance to NK cytolysis on target cells. These data strongly suggest that Cho-1 antigen expression may correlate with target cell susceptibility to NK cells. Indeed, treatment of NK-resistant WFB as well as HEPM cells with F(ab')2 fragments of mAb Cho-1 resulted in the acquisition of susceptibility to NK cytolysis. Cho-1 antigens may be novel molecules that regulate the NK resistance of cells.     

A self-organizing fuzzy control of weld pool size in GMA welding processes

In arc welding processes, because of the complexity and nonlinearity of heat transfer phenomena, it is often difficult to design an effective control system based upon an exact mathematical model. In this paper, a self-organizing fuzzy control method is proposed to obtain a uniform weld quality by regulation of the surface temperature at a desired level. The proposed control system is designed to comprise a combined structure of the fuzzy SOC with conventional PD control for improving the system's stability. The control experiments show that the proposed controller guarantees a uniform weld quality for various welding conditions.     

Wear and Wear Transition in Silicon Carbide Ceramics during Sliding

Wear and wear transition in silicon carbide ceramics during sliding have been investigated. Three different microstructures, i.e., solid-state-sintered silicon carbide, liquidphase-sintered silicon carbide, and a liquid-phase-sintered SiC-TiB₂ composite, were produced by hot pressing. Wear data and examinations of worn surfaces showed that the wear behavior of these silicon carbide ceramics was significantly different. In the solid-state-sintered silicon carbide, the wear occurred by a grooving process. In the liqudphase-sintered silicon carbide and composite, on the other hand, an abrupt transition in the wear mechanism from an initial grooving process to a grain pullout process occurred during the test. The transition occurred significantly earlier in the composite than in the carbide. The different wear behavior in these silicon carbide ceramics is discussed in relation to the grain or interphase boundary strength.     

Amorphous Ni---N---W film as a diffusion barrier between aluminum and silicon

The influence of nitrogen on the diffusion barrier properties of amorphous Ni---W films was studied. Nitrogen was introduced into the amorphous Ni---W film by co-sputtering nickel and tungsten in a premixed gas mixture of 90% Ar and 10% N₂, resulting in the formation of amorphous Ni₃₀N₂₁W₄₉ film. X-ray analysis indicates a detectable crystallization of the amorphous film after 30 min annealing in vacuum at 600°C, accompanied by the formation of W₂N, but backscattering spectrometry (BS) reveals a reaction with silicon only at about 725°C. The Schottky barrier height of this amorphous film on n-Si is stable for 30 min annealing up to at least 550°C. With an aluminum overlayer, BS indicates that an amorphous Ni₃₀N₂₁W₄₉ film effectively prevents the metallurgical interaction between aluminum and silicon for 30 min up to 600°C. The Schottky barrier height of that contact configuration is also stable up to at least 550°C, suggesting that amorphous Ni---N---W films have attractive features as diffusion barriers.     

A micromachined electrochemical sensor for free chlorine monitoring in drinking water.

In this work, we designed, fabricated and tested a disposable, flow-through amperometric sensor for free chlorine determination in water. The sensor is based on the principle of an electrochemical cell. The substrate, as well as the top microfluidic layer, is made up of a polymer material. The advantages include; (a) disposability from low cost; (b) stable operation range from three-electrode design; (c) fluidic interconnections that provide on line testing capabilities; and (d) transparent substrate which provides for future integration of on-chip optics. The sensor showed a good response and linearity in the chlorine concentration ranging from 0.3 to 1.6 ppm, which applies to common chlorination process for drinking water purification.     

Representation and reconstruction of polygons and polyhedra using Hierarchical Extended Gaussian Images

In this paper, two new representation schemes called the Branched Gaussian Image (BGI) and the Hierarchical Extended Gaussian Image (HEGI) are proposed. They can be used for uniquely representing both concave and convex, two-dimensional figures and three-dimensional objects. The representation by the Branched Gaussian Image involves several Gaussian spheres connected by branches where the traversing directions might be different. Examples showing how the use of the BGI enables us to achieve the mapping and inverse mapping of concave polygons and polyhedra uniquely are presented. The Gaussian spheres in the BGI can be organized into a tree-like hierarchical structure known as the Hierarchical Extended Gaussian Image. A general procedure for mapping a polygon or polyhedron to its HEGI representation is described. An approach for reconstructing concave polygons from Branched Gaussian Images is presented. The reconstruction of a concave polyhedron from its Hierarchical Extended Gaussian Images by using an iterative method or a closed-form method for each convex component is also described.