Study on the c-axis preferred orientation of ZnO film on various metal electrodes

ZnO thin film was deposited on various metal electrodes by reactive sputtering, and c-axis preferred orientation of the film has been studied. ZnO, which has high piezoelectricity, is promising for oscillators or filter devices such as surface acoustic wave (SAW) device, gas sensor, and film bulk acoustic resonator (FBAR). But, for the application of ZnO film for these devices, the film should be grown with c-axis normal to the electrode. In this study, Pt, Al, and Au were deposited on Si wafer, and the surface roughness and crystal structure of the ZnO film on the electrode were investigated using AFM, scanning electron microscopy (SEM), and X-ray diffraction (XRD). Columnar structures of ZnO films were grown with c-axis normal to all electrodes, and among them Pt electrode showed the highest preferred orientation of ZnO film.     

Preparation of multi-compositional gas sensing films by combinatorial solution deposition

Various compositions of gas sensing films were prepared by the combinatorial deposition of SnO₂, ZnO, and WO₃ sol solutions and their gas sensing behaviors were investigated. The film composition could be manipulated conveniently via the alternate dropping of different oxide sol solutions. From the correlation between film compositions and gas sensitivities, the selective detection of C₂H₅OH and CH₃COCH₃ in the presence of CO, C₃H₈, H₂, and NO₂ could be attained. In addition, the discrimination between C₂H₅OH and CH₃COCH₃, which is a challenging issue due to their similar chemical nature, becomes possible. This research demonstrates the precise design of the sensor-material composition for the selective gas detection via the combinatorial approach.     

Treatment of low turbidity water by sweep coagulation using bentonite

A novel strategy of sweep coagulation to treat low turbidity water is presented herein. Study findings demonstrated that an Na⁺‐saturated bentonite with medium cation exchange capacity (CEC) resulted in significant turbidity removal at a bentonite dosage of 30 mg dm^?3. Bentonite dispersion with fully delaminated platelets tended to undergo a more porous type of coagulation with intense face‐to‐face interactions of platelets and effectively entrapped TiO₂ particles in band‐type structures. This type of coagulation usually results in a large volume of settled flocs with a fluffy structure and excellent turbidity removal efficiency for sweep coagulation. The sign and magnitude of electrical charge on TiO₂ particles has a minor effect on the efficiency of sweep coagulation. Copyright © 2005 Society of Chemical Industry     

Infinite-dimensional convex optimization in optimal and robustcontrol theory

Many engineering problems can be shown to be equivalent to solving semidefinite programs (SPs), i.e., convex optimization problems involving linear matrix inequalities (LMIs). Powerful computation tools are available for such problems in the finite-dimensional case. However, the problems arising in optimal and robust control theory are often infinite dimensional, and so adequate computation tools are not available. The key to tackling such problems with finite computation tools is to have a primal-dual formulation of the problem without duality gap. In this paper we study infinite-dimensional SPs and present a lifting technique to recast SPs as parameterized linear programs (LPs). This enables the wealth of theoretical tools available for infinite-dimensional LPs to be extended to infinite-dimensional SPs. In particular, we develop some new sufficient conditions for the lack of a duality gap for infinite-dimensional SPs and give an exact characterization of the primal and dual problems for these cases. Both primal and dual problems are formed as infinite-dimensional SP problems, with finite truncations to each giving upper and lower bounds, respectively, on the exact solution to the infinite-dimensional problem. Thus, these results can form the basis of practical computation schemes for infinite-dimensional problems, which require only finite-dimensional computation tools. To illustrate the power of these tools we apply the results to two previously unsolved optimization problems, namely minimizing the l₁ norm of a closed-loop system subject to bounds on the frequency response magnitude at a finite number of points and/or bounds on the H₂ norm     

Virtual circuit connection method for RSVP multicasting supportingheterogeneous receivers on the ATM network

The authors suggest a novel virtual circuit connection method based on the reverse traversing technique to minimise the waste of network bandwidth resources, when the Internet protocol multicast is interoperated using the resource reservation protocol over an asynchronous transfer mode network. Simulation results show that, as the number of receivers increases, the bandwidth requirements on all links of the network of the proposed scheme become more advantageous than those of other conventional methods     

Interfacial reactions in the squeeze-cast (SAFFIL+C)/SAE 329 Al composite

Interfacial reactions in the squeeze-cast SAE 329 Al alloy reinforced with SAFFIL and carbon fibers were investigated using scanning and transmission electron microscopy and secondary ion mass spectroscopy. The SiO₂ layer added as a binder for the preform of SAFFIL fiber appeared to prevent excessive reaction between the fiber and the molten Al alloy during casting. In the as-cast composite, the reaction between the SiO₂ layer and the Al alloy is considered to produce MgO crystals in the vicinity of SAFFIL fiber. With subsequent heat treatment of the composite to the T6 condition, small crystals of MgO and MgAl₂O₄ were found to form at the surface of SAFFIL fiber as a result of interfacial reaction between the SiO₂ layer and the Al alloy. Even at the T6 condition, significant reactions between the Al alloy and SAFFIL fiber itself were not observed, indicating the effective role of the binder layer in suppressing the degradation of SAFFIL fiber by reaction with the Al alloy.     

HEURISTIC APPROACHES FOR LOADING PROBLEMS IN FLEXIBLE MANUFACTURING SYSTEMS

Flexible manufacturing systems (FMSs) are able to process a wide variety of operations, but the specific mix of operations that can be performed at any point in time depends upon the combination of tools loaded onto the machines. The machines have tool magazines with finite capacities. We consider the problem of assigning operations and their associated tools to machines (or groups of machines) to maximize the throughput for a specified steady-state mix of orders. Since this objective is difficult to deal with directly, we use an intermediate objective of meeting workload targets for each machine group as closely as possible. A certain form of this intermediate objective has been shown to correlate highly with the original objective.

Since it is computationally intractable to find optimal solutions for problems with more than 20 operations, fast heuristic algorithms are developed. These algorithms are adapted from multi-dimensional bin-packing algorithms. Computational results are reported.     

Parallel, self-organizing, hierarchical neural networks. II

For pt.I see IEEE Trans. Neural Networks, vol.1, p.167-78 (1990). Parallel, self-organizing, hierarchical neural networks (PSHNNs) involve a number of stages with error detection at the end of each stage, i.e., rejection of error-causing vectors, which are then fed into the next stage after a nonlinear transformation. The stages operate in parallel during testing. Statistical properties and the mechanisms of vector rejection of the PSHNN are discussed in comparison to the maximum likelihood method and the backpropagation network. The PSHNN is highly fault tolerant and robust against errors in the weight values due to the adjustment of the error detection bounds to compensate errors in the weight values. These properties are exploited to develop architectures for programmable implementations in which the programmable parts are reduced to on-off or bipolar switching operations for bulk computations and attenuators for pointwise operations     

A time-domain approach to transmission network equivalents viaProny analysis for electromagnetic transients analysis

This paper presents a method of obtaining transmission network equivalents from the network's response to a pulse excitation signal. The proposed method is based on modal decomposition representation for the large-scale interconnected system. In this framework we use Prony analysis to identify the network function of the system and to decompose the large system into a parallel combination of simple first-order systems. As a result the network function of the transmission network can be identified easily, and a Thevenin-type of discrete-time filter model can be generated. It can reproduce the driving-point impedance characteristic of the network. Furthermore, the proposed model can be implemented into the EMTP in a direct manner. The simulation results with the full system representation and the developed equivalent system showed a good agreement