Oxidation of accident tolerant fuel candidates

In this study, the oxidation of various accident tolerant fuel candidates produced under different conditions have been evaluated and compared relative to the reference standard – UO₂. The candidates considered in this study were UN, U₃Si₂, U₃Si₅, and a composite material composed of UN–U₃Si₂. With the spark plasma sintering (SPS) method, it was possible to fabricate samples of UN with varying porosity, as well as a high-density composite of UN–U₃Si₂?(10%). Using thermogravimetry in air, the oxidation behaviors of each material and the various microstructures of UN were assessed. These results reveal that it is possible to fabricate UN to very high densities using the SPS method, such that its resistance to oxidation can be improved compared to U₃Si₅ and UO₂, and compete favorably with the principal ATF candidates, U₃Si₂, which shows a particularly violent reaction under the conditions of this study, and the UN–U₃Si₂?(10%) composite.     

Comparative analysis of ceramic-carbonate nanocomposite fuel cells using composite GDC/NLC electrolyte with different perovskite structured cathode materials

A comparative analysis of perovskite structured cathode materials, La_0.65Sr_0.35MnO₃ (LSM), La_0.8Sr_0.2CoO₃ (LSC), La_0.6Sr_0.4FeO₃ (LSF) and La_0.6Sr_0.4Co_0.2Fe_0.8O₃ (LSCF), was performed for a ceramic-carbonate nanocomposite fuel cell using composite electrolyte consisting of Gd_0.1Ce_0.9O_1.95 (GDC) and a eutectic mixture of Na₂CO₃ and Li₂CO₃. The compatibility of these nanocomposite electrode powder materials was investigated under air, CO₂ and air/CO₂ atmospheres at 550 °C. Microscopy measurements together with energy dispersive X-ray spectroscopy (EDS) elementary analysis revealed few spots with higher counts of manganese relative to lanthanum and strontium under pure CO₂ atmosphere. Furthermore, electrochemical impedance (EIS) analysis showed that LSC had the lowest resistance to oxygen reduction reaction (ORR) (14.12 Ω·cm²) followed by LSF (15.23 Ω·cm²), LSCF (19.38 Ω·cm²) and LSM (>300 Ω·cm²). In addition, low frequency EIS measurements (down to 50 µHz) revealed two additional semi-circles at frequencies around 1 Hz. These semicircles can yield additional information about electrochemical reactions in the device. Finally, a fuel cell was fabricated using GDC/NLC nanocomposite electrolyte and its composite with NiO and LSCF as anode and cathode, respectively. The cell produced an excellent power density of 1.06 W/cm² at 550 °C under fuel cell conditions.     

Aerosol analysis of residual and nanoparticle fractions from spray pyrolysis of poorly volatile precursors

The quality of aerosol‐produced nanopowders can be impaired by micron‐sized particles formed due to non‐uniform process conditions. Methods to evaluate the quality reliably and fast, preferably on‐line, are important at industrial scales. Here, aerosol analysis methods are used to determine the fractions of nanoparticles and micron‐sized residuals from poorly volatile precursors. This is accomplished using aerosol instruments to measure the number and mass size distributions of Liquid Flame Spray‐generated alumina and silver particles produced from metal nitrates dissolved in ethanol and 2‐ethylhexanoic acid (EHA). The addition of EHA had no effect on silver, whereas, 5% EHA concentration was enough to shift the alumina mass from the residuals to nanoparticles. The size‐resolved aerosol analysis proved to be an effective method for determining the product quality. Moreover, the used on‐line techniques alone can be used to evaluate the process output when producing nanopowders, reducing the need for tedious off‐line analyses. © 2016 American Institute of Chemical Engineers AIChE J, 63: 881–892, 2017     

The effect of water‐soluble polymers on rheology of microfibrillar cellulose suspension and dynamic mechanical properties of paper sheet

Rheological properties of fiber/polymer suspensions and dynamic mechanical analysis (DMA) of paper sheets containing the same polymers were measured. Correlations between viscoelastic properties of suspensions and strength of paper sheet are presented. Rheological properties of suspensions of microfibrillar cellulose (MFC) and a set of water soluble polymers were measured. Rheological properties of these complex fluids vary considerably depending on the added polymer. A suspension of fiber and carboxymethyl cellulose (CMC) exhibits a viscosity higher than the sum of the viscosity of the individual components in the suspension. In contrast, when cationic starch (CS) is used together with the fiber, the yielding behavior rather than the viscosity is characteristic of the suspension. Dynamic mechanical properties of paper sheets containing CMC or CS as additives were studied at different humidity levels. Different yielding behavior observed in oscillatory rheology can be correlated with straining behavior in dynamic mechanical properties. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Miscibility,morphology and mechanical properties of rubber‐modified biodegradable poly(ester‐urethanes)

Biodegradable, lactic acid based amorphous poly(ester‐urethane)s (PEU) were modified with poly(L‐lactic acid‐co‐ϵ‐caprolactone‐urethane) elastomer (P[LA/CL]U) by melt blending. The phase separation of P(LA/CL)U elastomer with three different ϵ‐caprolactone (CL) compositions (CL content 30, 50, and 70 mol %) and the mechanical properties of the resulting impact‐modified linear and branched PEU were investigated. The amounts of P(LA/CL)U elastomer in the PEU blends were 10, 15, 20, and 30 wt %. Dynamic mechanical thermal analysis (DMTA) of the blends with P(LA50/CL50)U and P(LA30/CL70)U elastomers revealed separate glass transition temperatures for rubber and matrix, indicating phase separation. No phase separation was found for P(LA70/CL30)U elastomer. The effect of mixing rate and temperature during processing on composite properties was tested by blending P(LA30/CL70)U rubber with PEU under various processing conditions. Impact modification studies were also made with two P(LA30/CL70)U elastomers having different amounts of functional groups. The influence of end‐functionalization and cross‐linking on mechanical properties was investigated in blends containing PEU and 15 wt % of these elastomers. Scanning electron microscopy (SEM) showed the morphology to change dramatically with increase in the degree of cross‐linking in the rubber. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 1074–1084, 2000     

Effect of structure modification on rheological properties of biodegradable poly(ester‐urethane)

Biodegradable lactic acid based poly(ester‐urethanes) (PEU) were polymerized and their structure and rheological properties were characterized. The polymerization process comprised two steps: lactic acid monomer was oligomerized to low molecular weight prepolymer, and this was then linked to high molecular weight PEU with chain extender, 1,6‐hexamethylene diisocyanate. The properties of PEU were modified by varying the amount of chain extender from 1.05:1 to 1.35:1 (NCO/OH ratio). The modification was mostly seen in the molecular weight distribution of the polymers, which was broadened from 2.2 to 3.5 as the amount of chain extender was increased. The telechelicity of the prepolymer was found to play an essential role in successful linking of the prepolymer units. In addition, the rheological properties of poly(ester‐urethane) were determined with capillary and dynamic rheometers. All PEU samples were pseudoplastic and broadening of their molecular weight distribution was accompanied by increased viscosity and complex viscosity at low shear rates and increased shear thinning. The temperature dependency of the measurement was pronounced. Rheological measurements also showed that PEU starts to degrade at 100°C and further rise in temperature increases the rate of degradation significantly.     

The modification of lactic acid based poly(ester-urethane) by copolymerization

Copolymers of L-lactic acid (LLA) with DL-mandelic acid (DLMA), 4-hydroxybenzoic acid, 4-acetoxybenzoic acid, DL-malic acid, or anhydrous citric acid were synthesized via direct copolycondensation in the presence of 1,4-butanediol, using stannous octoate as catalyst. The effect of the comonomer and the comonomer ratio on polycondensation and the glass transition temperature were investigated. The glass transition temperature of amorphous poly(L-lactic acid-co-DL-mandelic acid) increased linearly from 33° to 56°C as the mandelic acid composition was increased from 0 to 45 mol %. For urethane synthesis, prepolymers of LLA and DLMA were condensation polymerized with compositions of 100/0, 90/10, and 80/20 (mol % in feed). The preparation of poly(ester-urethane) (PEU) was carried out in a stirred glass reactor, using 1,6-hexamethylene diisocyanate and isophorone diisocyanate in melt. The glass transition temperature of poly(L-lactic acid-co-DL-mandelic acid-urethanes) showed a marked increase with increased mandelic acid composition. The molecular weights of these urethanes were lower than for PEU based on poly(L-lactic acid). Such a depression in the degree of polymerization is attributed to the steric hindrance of the bulky phenyl group as a side chain of mandelic acid. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 63: 1865–1872, 1997     

Wetting behaviour and direct observation of thermally responsive polystyrene‐block‐poly(N‐isopropylacrylamide)‐block‐polystyrene electrospun fibres in aqueous environment

Electrospun fibres of thermally responsive triblock copolymer polystyrene‐block‐poly(N‐isopropylacrylamide)‐block‐polystyrene were prepared. Fibre morphology and swelling were studied below and above the lower critical solution temperature of poly(N‐isopropylacrylamide) (PNIPAM) using cryo‐electron microscopy. Cryo‐transmission electron microscopy showed that the fibre diameter increased up to 150% after immersion in water at 20 °C. In contrast, at 45 °C the fibre diameter increased considerably less. The sessile drop technique was used to characterize temperature‐dependent wetting of fibre mats. Contact angle (θ_CA) measurements revealed that a block copolymer fibre mat changed from hydrophobic (θ_CA > 90°) to hydrophilic (θ_CA < 90°) state within seconds after applying a water droplet on it at 20 °C. At 40 °C the initial contact angle was measured to be higher (135°) and it decreased much less than at 20 °C during the first minute of measurement. We observed using scanning electron microscopy that the electrospun fibres of the block copolymer having 77 wt% of PNIPAM lost their cylindrical shape and changed from fibres to thin sheets at both 20 and 40 °C within seconds after applying water on the fibres. Fibres having 55 wt% of PNIPAM were observed to be stable in water at both 20 and 40 °C, which resulted, surprisingly, in fibre mats with the strongest effects on thermally sensitive wetting. We discuss the surprising results and the implications that the evolution of fibre surface roughness has on the long‐term wetting behaviour, demonstrating a self‐adaptable hydrophilicity/hydrophobicity nature of the fibre mats. © 2013 Society of Chemical Industry     

Novel two‐stage phenol–formaldehyde resol resin synthesis

The synthesis of phenol–formaldehyde resol resins was carried out in two stages to facilitate the start of a conventional batch process. In the first stage, the starting material solution was preprocessed in a continuous‐flow stirred‐tank reactor with a 5‐min residence time. In the second stage, synthesis was continued in a batch reactor. Samples were analyzed by titrimetric methods, gas chromatography, nuclear magnetic resonance spectroscopy, and differential scanning calorimetry. Most of the starting materials were consumed in the preprocessing reactor, which allowed better control of the reactivity of the prepolymer solution in the second stage. The methylolation and condensation reactions proceeded steadily during the production process in the batch reactor. The results of the study indicated that dividing a conventional one‐stage batch process into two stages could facilitate the control of the initial stages of resol production. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103:371–379, 2007     

Fatty Acid Fingerprints and Hyaluronic Acid in Extracellular Vesicles from Proliferating Human Fibroblast-like Synoviocytes

Extracellular vesicles (EVs) function as conveyors of fatty acids (FAs) and other bioactive lipids and can modulate the gene expression and behavior of target cells. EV lipid composition influences the fluidity and stability of EV membranes and reflects the availability of lipid mediator precursors. Fibroblast-like synoviocytes (FLSs) secrete EVs that transport hyaluronic acid (HA). FLSs play a central role in inflammation, pannus formation, and cartilage degradation in joint diseases, and EVs have recently emerged as potential mediators of these effects. The aim of the present study was to follow temporal changes in HA and EV secretion by normal FLSs, and to characterize the FA profiles of FLSs and EVs during proliferation. The methods used included nanoparticle tracking analysis, confocal laser scanning microscopy, sandwich-type enzyme-linked sorbent assay, quantitative PCR, and gas chromatography. The expression of hyaluronan synthases 1–3 in FLSs and HA concentrations in conditioned media decreased during cell proliferation. This was associated with elevated proportions of 20:4n-6 and total n-6 polyunsaturated FAs (PUFAs) in high-density cells, reductions in n-3/n-6 PUFA ratios, and up-regulation of cluster of differentiation 44, tumor necrosis factor α, peroxisome proliferator-activated receptor (PPAR)-α, and PPAR-γ. Compared to the parent FLSs, 16:0, 18:0, and 18:1n-9 were enriched in the EV fraction. EV counts decreased during cell growth, and 18:2n-6 in EVs correlated with the cell count. To conclude, FLS proliferation was featured by increased 20:4n-6 proportions and reduced n-3/n-6 PUFA ratios, and FAs with a low degree of unsaturation were selectively transferred from FLSs into EVs. These FA modifications have the potential to affect membrane fluidity, biosynthesis of lipid mediators, and inflammatory processes in joints, and could eventually provide tools for translational studies to counteract cartilage degradation in inflammatory joint diseases.