科技期刊编辑专业化和学者化是保证期刊学术质量的关键

一般科技期刊刊载的论文内容都具有很强的专业性,这就要求科技期刊编辑必须具有丰富的专业知识和较高的学术水平才能胜任编辑工作.从编辑过程的选题组稿、论文初审、选择审稿专家和编辑加工四个方面对此进行了阐述,指出了提高科技期刊编辑的相关专业知识和学术水平的措施.     

UV-LIGA深度光刻机平滑衍射技术研究

UV-LIGA深度光刻技术是加工微型机电系统的一项重要的微细加工技术。介绍了一种平滑衍射效应的位错强度叠加原理，它采用了蝇眼积分透镜去平滑衍射，并模拟数值计算了硅片表面的光强分布，最后给出了光刻结果。     

西北江三角洲来水来沙的非线性分形特征

根据西、北江干流高要、石角及西北江三角洲网河区顶点马口、三水四个水文站的流量和含沙量资料 ,应用非线性分形原理的R S方法 ,计算西北江干流及西北江网河区顶点四个水文站的流量、含沙量的赫斯特数H和分形维数D ;探讨西、北江干流来水来沙的分形特征及西北江三角洲的分水分沙规律。结果表明 ,流量的分维数略大于含沙量的分维数 ,三水站流量及含沙量的分维数与其上游的石角站流量、含沙量的分维数相差较大 ,与思贤的分水分沙造成西北江的水沙交换有关     

高速钢高温形变诱发析出的研究

本文探讨了高速钢在高温形变过程中碳化物析出的行为及奥氏体组织状态对析出的影响。用透射电镜和扫描电镜分析了不同热处理状态奥氏体的组织结构,分析了高温形变过程中碳化物析出的部位,颗粒尺寸及形态。试验表明, 碳化物主要在奥氏体的缺陷处呈点状和点列状析出,大小为20mμ。处于回复状态的奥氏体缺陷诱发碳化物析出,析出碳化物钉札缺陷阻止再结晶进行。当再结晶驱动力较大时,由于动态再结晶充分发展,使缺陷大量消除,碳化物析出显著地减少。     

石化装置检修的安全管理

针对石化装置的检修特点,阐述装置检修的安全管理和技术工作,对检修时的高风险作业提出明确的要求和注意事项.     

Pattern search algorithms for nonlinear inversion of high-frequency Rayleigh-wave dispersion curves

Inversion of Rayleigh wave dispersion curves is challenging for most local-search methods due to its high nonlinearity and to its multimodality. In this paper, we implemented and tested a Rayleigh wave dispersion curve inversion scheme based on GPS Positive Basis 2N, a commonly used pattern search algorithm. Incorporating complete poll and complete search strategies based on GPS Positive Basis 2N into the inverse procedure greatly enhances the performance of pattern search algorithms because the two steps can effectively locate the promising areas in the solution space containing the global minima and significantly reduce the computation cost, respectively.The proposed inverse procedure was applied to nonlinear inversion of fundamental-mode Rayleigh wave dispersion curves for a near-surface shear (S)-wave velocity profile. The calculation efficiency and stability of the inversion scheme are tested on three synthetic models and a real example from a roadbed survey in Henan, China. Effects of the number of data points, the reduction of the frequency range of the considered dispersion curve, errors in P-wave velocities and density, the initial S-wave velocity profile as well as the number of layers and their thicknesses on inversion results are also investigated in the present study to further evaluate the performance of the proposed approach.Results demonstrate that pattern search algorithms applied to nonlinear inversion of high-frequency surface wave data should be considered good not only in terms of accuracy but also in terms of the computation effort due to their global and deterministic search process.     

Fabrication of Functional Nanofibrous Ammonia Sensor

A nanofibrous sensor for ammonia gas is fabricated by electrospinning the composite of poly(diphenylamine) (PDPA) with poly(methyl methacrylate) (PMMA) onto the patterned interdigit electrode. The composite electrospun membrane shows interconnected fibrous morphology. Functional groups in PDPA and the high active surface area of the fibrous membrane make the device detect a lower concentration of ammonia with a good reproducibility. The sensing capability of the device is studied by monitoring the changes in resistance of the membrane with different concentrations of ammonia. The changes in resistance of the membrane shows linearity with the concentration of ammonia in the limit of 10 and 300 ppm. UV-visible spectroscopy reveals the mechanism of sensing ammonia by the membrane.     

MHD simulation of high-current subsonic vacuum arc under different distributed axial magnetic fields

Based on two-temperature magnetic hydrodynamic (MHD) model, the influence of saddle-shaped distributed axial magnetic field (AMF, linearly increases along radial position) and bell-shaped distributed AMF (linearly decreases along radial position) on plasma loss and heat flux density to anode in subsonic high-current vacuum arc (HCVA) is simulated and analyzed. According to the simulation results, the saddle-shaped AMF can more effectively inhibit plasma loss from arc column than that of bell-shaped AMF. Comparisons between simulation results and experimental results further verify the correctness of model and simulation.     

自蔓延高温合成TiNi多孔体合金

为了开发新型的生体材料，本文对自蔓延高温合成TiNi多孔体合金——人造骨材料进行了研究。以单质钛粉和镍粉作原料，在氩气保护条件下，采用预热点燃模式和热爆模式制得了不同形态的多孔TiNi形状记忆合金。采用SEM和XRD分析了样品的孔洞特征和相组成，测试了其力学性能，并研究了合成条件参数与样品表面形貌和孔隙状态之间的关系。结果表明，用SHS法制备TiNi多孔体合金是可行的。     

浅议实施差异化战略的措施

随着我国市场的开放，企业面对的竞争日趋激烈，而且企业的竞争优势主要表现为差异化。根据差异化与买方价值的关系，通过技术创新、观念创新实施差异化。